WatchGuard Technologies DVR4ENTPACK User Manual

www.watchguardalarms.com.au

MODEL: DVR4ENTPACK

Professional Surveillance Pack

Digital Vi deo Recorder with 4 Security Cameras

‘QUICK INSTALLATION GUIDE’

N517

DVR 2 x Cameras –30m Infrared range for night operation

- Advanced MPEG4 Video Compression Technology - High Quality CCD Image sensor

- Multiplex Operation - 24 x IR LED’s

- Long Recording Duration - 420 TVL Resolution, 520 x 582 Pixels

- Intelligent Video Motion Detection Recording 2 x Cameras –15m Infrared range for night operation

- Remote Network Surveillance & Backup Functions - High Quality CCD Image sensor

- Easy to operate like a VCR - 12 x IR LED’s

- System Auto recovery after power loss (blackout) - 420 TVL Resolution, 520 x 582 Pixels

Package Contents (Before commencing installation, please ensure you have all the parts listed below.)

* Note: If you wish to connect directly from the DVR to a PC you require a crossover cable (Not Included)

Monitor

1

Installation

Before installing this unit, please read through the following points:

• Do not place cords from the AC adapter where they can be pinched or stepped on.

• Do not place heavy objects on cords, or cover cords with rugs or carpet.

• Never immerse any component in water, and do not spray cleaners of solvents on the unit. Unplug

units before cleaning. When cleaning, use a damp, lint-free cloth only.

• Do not expose the DVR or Camera’s to excessive heat, cold, or moisture

• Leave at least a 2” space between the DVR and other objects to allow air circulation around the unit.

• Service should be handled by qualified technicians.

Impedance
matching not
required with
this camera
package

Not used with
this camera
package

1

2

Optional – Input/Output sensing
Not used with this package

3

5

4

6

7

8

WARNING

Please ensure you use

the correct power

supply for each

component.

DO NOT plug the 19V

DVR Power supply into

the cameras as this will

damage them

.

Connection Guide

1. Locate the 4 Cameras as required and connect the supplied combination DC Power and Video
leads. (Yellow to Yellow / Red to Red)

2. Connect the 4 x corresponding camera Video leads (Yellow) into the camera inputs at the rear of
the DVR (Take note of the Camera input 1 – 4, as this will determine the camera channels)

3. Connect the 4 x camera DC Power leads (RED) into the Power Split Cable

4. Connect the Monitor Connection Cable into the BNC Monitor output on the rear of the DVR.

5. Connect the Monitor Connection Cable into the RCA Video input on your TV/Monitor

(TV/Monitor Not Supplied) Note: (Requires composite video input monitor - not VGA)

6. Connect the 2Amp 19VDC Power adaptor to the DVR

7. Connect the 12VDC Power adaptor to the Power Split Cable.

8. Plug both Power adaptors into a 240Volt / AC Power Point and switch power point ON

9. The Power LED at the front of the DVR should now be illuminated Red and the unit will make a
loud beep sound.

2

Quick Start up Guide

• Make sure your TV/Monitor is ON and set to the appropriate AV channel if required

• Press the Power button located on the front panel of the DVR, the LED will illuminate Green

it takes approximately 10 to 15 seconds to boot the system.

• The images from all 4 cameras should now be displayed on your TV/Monitor

• BEFORE BEGINNING TO RECORD YOU MUST SET the DATE and TIME on your DVR.

Setting the Date and Time

• Press “MENU” button to enter the (OSD) On Screen Display menu list.

The default admin password is 0000.

Enter the default password by pressing “ENTER” 4 times.

(Users can alter the password later. Please refer to the Advanced set up guide CD)

• Use the following buttons to move the cursor for menu settings:

“UP=▲,DOWN=▼,LEFT=◄,RIGHT=► “

(MENU)

RECORD

TIMER

DDAATTEE

ADVANCE

LEFT

• Move the cursor to “DATE” and press, ”ENTER”. The screen will show the following options

DATE 12 - MAY - 2006 16:30:00

FORMAT D-M-Y

DAYLIGHT SAVING ON

DDAATTEE

3

UP

RIGHT

DOWN