Page 1
Design for Manufacturing and Environment Document
Document Number: 480-2524-001
De-manufacturing
Firebox V10
Instructions
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 1 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 2
Design for Manufacturing and Environment Document
1.0 Purpose
This instruction defines the de-manufacturing process for the recovery of this product
family as it pertains to recycling of the major product components.
2.0 Scope
This instruction applies to the following product family and family part numbers.
Product Family Name Family part #’s (not necessarily inclusive)
Firebox V10
• Firebox V10; all revisions
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 2 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 3
3.0 Instruction
3.1 -Remove labels, rubber feet and screws
Material removed (part
Desc or P/N & material
type)
Labels
Cert. label:
0791-00x– Metalized
poly-film
Warranty void:
0230-001 - Poly-film
Serial number:
0812-00x - Poly-film
Product UPC:
0813-00x - Poly-film
Rubber Feet
0428-002 - PSA clear; 4
ea.
Design for Manufacturing and Environment Document
Instruction visual
Remove rubber feet
Remove labels
Screws
0792-001 - Phillips
head; steel; 4 ea.
Remove screws, 4 ea.; one
under warranty void label
3.2 –Disengage top from display and disconnect display from Interconnect PCBA
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 3 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 4
Material removed (part
Desc or P/N & material
type)
Upper housing
0788-001- PC/ABS FR110
Design for Manufacturing and Environment Document
Instruction visual
Disengage press fit
display from upper
housing with fingers
Disconnect display module by
lifting corner locks and pulling
display flex circuit
3.3 –Disassemble display module
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 4 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 5
Material removed (part
Desc or P/N & material
type)
Flex Circuit
0784-001- Flex PCBA with
SC42 Neoprene backing
Lens Components
Lens front
0781-001- Polycarbonate
Lightpipe
0782-001- Polycarbonate
Design for Manufacturing and Environment Document
Instruction visual
Pull flex circuit with
backing from display
lens
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 5 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 6
3.4 –Remove Connector Hex Head Standoffs and separate PCBA Assembly
from Lower Housing
Material removed (P/N
& material type)
Stand-offs
xxxx-0xx – Hex-head
stainless steel; 2 ea.
Design for Manufacturing and Environment Document
Instruction visual
Lower housing
0789-001- PC/ABS FR110
Remove standoffs -2 ea.
Separate PCBA from
lower housing
3.2 –Disconnect PCBA Posts and Remove from Interconnect PCBA
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 6 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 7
Material removed (P/N
& material type)
Design for Manufacturing and Environment Document
Instruction visual
Interconnect PCBA
0774-001- PCBA
Locking posts
0778-001- Nylon; 5 ea.
Disconnect PCBA from base
housing, 5 places
Separate plastic posts
from Interconnect PCBA,
5 ea.
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 7 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 8
3.3 – Remove battery from Main PCBA
Material removed (P/N
& material type)
Battery –coin cell
0301-001– Manganese
oxide / Lithium CR2032
Design for Manufacturing and Environment Document
Instruction visual
Remove Battery from
clip
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 8 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 9
3.2 –Disconnect PCBA Connector and Separate PCBA, EMI Shield and Base
Material removed (P/N
& material type)
Design for Manufacturing and Environment Document
Instruction visual
Disconnect PCBA from base
housing with pressure with tool
or fingers, 2 places
Main PCBA
0748-001- PCBA
Locking posts
0776-001- Nylon; 2 ea.
Base housing
0775-001- PC/ABS FR110
EMI Shield
0775-001- Metalized EMI
paper
Separate PCBA, EMI
shield and base housing.
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 9 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Page 10
Design for Manufacturing and Environment Document
4.0 Applicable Documents
5.0 Revision History
REV.
NO.
A 10/10/2005 n/a Initial Release 0712
REV. DATE
REVISED SECTION REASON ECO#
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 10 of
10
Authorization and Revision History for this document is available in the WatchGuard ECO system
Loading...