Waste King ARC-4200 User Manual

ARC-4200 ON/OFF SAFETY AIR SWITCH

AS-4201 AIR SWITCH

GARBAGE

DISPOSER

HOT

OUTLET

PLUG

ARC-4200

CONTROL MODULE

1/8”

AIR TUBING

DESCRIPTION

The ARC-4200 consists of easy to install components for air actuated on/off control for use with any electrical
device up to1HP, 120V. Simply plug the ARC-4200 control module into any standard electrical outlet then
plug the appliance into the receptacle provided in the control module. The appliance can be activated and
deactivated by depressing an air button mounted up to 10 feet away.

TYPICAL INSTALLATIONS

AS-4201 AIR SWITCH

TUB

GFCI
PROTECTED
OUTLET

PUMP

DISPOSER APPLICATION (plug-in)

• Eliminates need for an electrical wall switch.

• Simplifies first time food waste disposer
installations.

• Operates on 120V household wall receptacle.

JET TUB APPLICATION (plug-in)

DIMENSIONS

READ AND SAVE THESE INSTRUCTIONS

Anaheim Manufacturing Co. • Registered to ISO 9001
4240 E. La Palma Ave. • Anaheim, CA 92807
[phone] • www.anaheimmfg.com

Made in U.S.A.

560C477P01 REV C

ARC-4200

CONTROL MODULE

1/8”

AIR TUBING

1 3/8”

Mounting Hole

Required

1 13/16”

IMPORTANT SAFETY INSTRUCTIONS

1. A pressure wire connector is provided on metallic enclosures to permit connections of a minimum No. 8 AWG solid copper
bonding conductor between any metal equipment, metal enclosures of electrical equipment, metal water pipe, or conduit
within 5 feet (1.5 m) of the unit as needed to comply with local requirements. Polymeric enclosures are supplied with an
internal equipment ground bar.

2. THIS CONTROL MUST BE FACTORY INSTALLED OR INSTALLED BY A LICENSED ELECTRICIAN ACCORDING TO STATE,
NATIONAL, AND LOCAL ELECTRICAL CODE AND THE INSTRUCTIONS.

3. Use copper conductors only.

4. DANGER - To reduce the risk of injury do not permit children to use this product unless they are closely supervised at all times.

5. Install to provide drainage of compartment for electrical components.

6. A ground-fault circuit interrupter (GFCI) designated line is to be installed in accordance with the National Electrical Code, the
Canadian Electrical Code and all local codes in effect at the time of installation. When unit is provided with a GFCI, the GFCI
must be tested monthly. To conduct the test the unit must be operating. Push the test button. The unit should stop operating
and the reset button should appear. Push the reset button. The unit should now operate normally. If the interrupter fails to
operate in this manner, there is a ground current flowing, indicating the possibility of electric shock. Disconnect the power
until the fault has been corrected.

7. The electrical supply for this product must include a suitably rated switch or circuit breaker to open all ungrounded supply
conductors to comply with Section 422-20 of the National Electrical Code, ANSI/NFPA 70-1987. The disconnect must be readily
accessible to the tub occupant but installed at least 5 feet (1.5m) from tub water.

8. No electrical appliance may be placed within a 5 foot reach path from the water’s edge.

9. Use only non-conductive tubing to connect any air actuator.

Anaheim Manufacturing Co. • Registered to ISO 9001
4240 E. La Palma Ave. • Anaheim, CA 92807
[phone] • www.anaheimmfg.com

Made in U.S.A.

560C477P01 REV C

READ AND SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

WARRANTY

Anaheim Manufacturing warrants its products to be free from
defects in workmanship and material under normal use and
conditions for a period of one year from the date of original
manufacture. Should repair be required by reason of any defect
or malfunction during the warranty period, Anaheim
Manufacturing will repair, or at their discretion, replace this
product without charge, subject to verification of the defect or
malfunction, upon delivery of the product to the attention of:

Customer Service Department
Anaheim Manufacturing Company
4240 E. La Palma Ave
Anaheim, CA 92807

If repair is required after the expiration date of the warranty
period, Anaheim Manufacturing will repair this product and
bill for any necessary replacement parts, shipping and
handling.

This warranty is void if: 1) the unit is not installed per the
instructions; 2) is hooked up to improper voltage; 3) is
subjected to chemical corrosion; 4) is mechanically or
electrically altered in any way; 5) is subjected to water or
immersion; 6) contacts show evidence of short circuiting, or the
unit has been visibly damaged by accident or misuse or which
has been damaged by wind, rain, lightning, freezing or other
cause; or upon which the serial number or manufacture date
has been altered, effaced or removed. There is a charge for
replacement parts if the defective unit is returned for any of the
reasons listed above.

Anaheim Manufacturing shall not be liable for any
inconvenience, loss of time, or incidental expenses incurred.
Anaheim Manufacturing shall not be liable for any labor
charges associated with the removal or reinstallation of any so­claimed defective products.

This is the only warranty expressed or implied by Anaheim
Manufacturing, Warranties implied under state law, including
any implied warranty of merchantability or fitness for a
particular purpose, shall be limited to one year from the date of
manufacture.

Anaheim Manufacturing disclaims any liability for any
incidental or consequential damages.

Ship as follows:

1. Pack the unit in a well padded, heavy corrugated box.

2. Include name, return address, and daytime phone number
along with a short description of problem with control.

3. Mail the unit, prepaid, to the above address.

Some states do not allow the exclusion or limitation of
incidental or consequential damages, therefore the above
limitation may not apply to you.