Page 1
OPERATOR'S MANUAL
取扱説明書
Wave Analyzer
波浪解析ソフトウェア
WV-100
Model
WV-100ST
www.furuno.com
Page 2
TABLE OF CONTENTS
FOREWORD................................................................................................................. ii
SYSTEM CONFIGURATION ....................................................................................... iv
1. OPERATIONAL OVERVIEW................................................................................. 1
1.1 How to Start and Quit the Software............................................................................1
1.2 Display Screen Overview ........................................................................................... 3
1.2.1 Wave spectrum display area............................................................................... 4
1.2.2 Radar echo display area ..................................................................................... 5
1.2.3 Significant wave height, wave information .......................................................... 5
1.3 Keyboard Operations.................................................................................................. 6
1.4 Orientation Mode........................................................................................................6
1.5 Analysis Update Time.................................................................................................7
1.6 Menu Overview........................................................................................................... 7
1.7 How to Take a Screenshot of a Display Screen......................................................... 7
1.8 System Information.....................................................................................................7
1.9 How to Update the Software.......................................................................................8
2. PRINCIPLE OF OPERATION, HOW TO INTERPRET THE DISPLAY ............... 10
2.1 Principle of Measurement......................................................................................... 10
2.2 Reliability of Analysis Results................................................................................... 10
3. ALERTS ............................................................................................................... 12
4. TROUBLESHOOTING......................................................................................... 13
4.1 Troubleshooting........................................................................................................ 13
4.2 System Information...................................................................................................14
APPENDIX1 MENU TREE...................................................................................... AP-1
APPENDIX2 ALERT LIST ...................................................................................... AP-2
APPENDIX3 SERIAL OUTPUT DATA ................................................................... AP-3
APPENDIX4 SEA-TRIAL MODE (For WV-100ST) ................................................ AP-5
63(&,),&$7,21663
i
Page 3
FOREWORD
Congratulations on your choice of the FURUNO Wave Analyzer WV-100/WV-100ST. We are confident you will see why the FURUNO name has become synonymous with quality and reliability.
Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and
dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers.
Please carefully read and follow the recommended procedures for operation and maintenance.
Features
This software, installed in a PC, analyzes and displays the wave radar data obtained from the FURUNO model chart radar FAR-3xx0 or marine radar FAR-2xx8 series.
• Automatic wave height adjustment.
• Wave analysis for both X-band and S-band radars.
• Equipped with sea trial mode (WV-100ST only).
• Always connect the PC to the Navigation network via a firewall device, as shown in the System
Configuration diagram.
Usage Precautions
To prevent potential damage to your radar, follow the below precautions:
• Only connect the analysis PC for wave analysis. Do not connect the PC for any other purpose.
• Do not install any other software on the PC, other than this analysis software.
• Always connect the PC to the Navigation network via a firewall device, as shown in the System
Configuration diagram.
• Do not connect the analysis PC to the ship-board network, or other networks, directly. Always
perform updates to Windows and anti-virus software while offline.
• Before connecting a USB Flash Memory or other USB storage device to the PC, preform a virus
check on the device and confirm that the storage can safely be connected to the PC.
• Only authorized personnel (PC administrator or users with administrative privileges) should use
this software.
• Anti-virus and security software can prevent this software from working correctly. Adjust your
anti-virus and security settings so that this software is white-listed. This software is designed to
be compatible with Windows Defender.
• Before using the PC for a purpose other than wave analysis, or before discarding the PC, uninstall this software.
ii
Page 4
FOREWORD
Restrictions on wave analysis
The following restrictions apply to wave analysis.
Radar settings
• Pulse width: Must be set between S1 and M1 (S1 has the highest measurement accuracy.)
• The wave analysis is not available when using the interswitch function. (The slave echo for the
interswitch is used for the wave analysis. The wave setting is canceled at the interswitch.)
Operational specification of wave radar
• This software analyzes wave data using the radars specified beforehand.
• To enable wave analysis, access the settings on the connected radar and switch [WAVE
MODE] to [ON].
In both cases, an error display appears when the analysis results are outside the capabilities of
this software.
Program version no.
0359495-01.**
* denotes minor modifications.
Software used in this product
This product includes software to be licensed under BSD, MIT, zlib, FTL, NVIDIA CUDA Toolkit
License Agreement. Please refer to the OSS directory in the supplied CD-ROM for details on the
terms of the software.
iii
Page 5
SYSTEM CONFIGURATION
LAN1
Antenna Unit
Gyrocompass,
GPS Navigator
Wind Sensor
*1
Intelligent HUB
HUB-3000
Processor Unit
Control Unit Monitor Unit
CHART RADAR FAR-3xx0 series
or
MARINE RADAR FAR-2xx8 series
PC
*2
for wave analysis
(Local supply, wave analyzer
software installed in PC)
*1
: For wave analysis, required wind
direction/speed data from the
wind sensor. The data should be
directly input to the radar, or
available on the network via
sensor adapter.
*2
: The PC should be connected to the
LAN1 port during wave analysis.
Firewall
Wave analysis PC
iv
Page 6
1. OPERATIONAL OVERVIEW
Retry
Cancel
1.1 How to Start and Quit the Software
1. Power the FAR-3xx0 or FAR-2xx8 series.
2. Insert the USB dongle into a USB port on the PC. The LED in the dongle lights red.
Note: The USB dongle is required to use this software. Take care not to lose it.
3. Power the PC. The software automatically starts up and the following screen appears.
Note 1: If the message shown to the right figure appears,
click [OK] to delete the message and then re-insert the
USB dongle.
Note 2: If the message for software error appears, click
[OK] to delete the message and then re-insert the USB
dongle. Double-click the shortcut icon for the software on
the desktop to start up the software.
Note 3: If the USB dongle is removed after starting the software, the following message appears.
Click [Cancel] to quit the software. Insert the USB dongle and double-click the shortcut icon
for the software on the desktop to restart the software.
1
Page 7
1. OPERATIONAL OVERVIEW
Attention!
Startup failed because setting file can not be read.
Restore all default settings and restart the software?
NO
(Cancel and exit)
YES
(Restore and restart)
Note 4: If the firewall is not configured, the error message to the below-left appears. Click
[OK], the message to the below-right then appears.
Click [OK] to delete the message, then open the [Enable Firewall for Wave Analyzer] shortcut
on your desktop. If the [User Account Control] dialog appears, click [Yes].
4. To quit the software, click the close button (x) at the upper right corner of the screen. The confirmation message "Are you sure you want to exit?" appears.
5. Click [YES] to quit the software.
Check of the setting file at startup
This software checks if the setting file can be read at startup. If the setting file is corrupted, the
following message appears.
• Click [YES] to restore the default settings, then start up the software. The saved settings are
deleted.
• Click [NO] to cancel and close the software.
2
Page 8
1. OPERATIONAL OVERVIEW
99
11
33
44
22
55
1010
1111
1414
66
77 88
1313
1212
13 25
1.2 Display Screen Overview
The screen looks something like the one shown below when the radar is transmitting pulses and
waves are being analyzed.
No. Name Description
1 Wave spectrum display area Shows 2D wave spectrum.
2 Radar echo display area Shows radar echo for wave analysis from the specified ra-
dar.
3 Wind sensor information Shows wind direction and wind speed.
4 Own ship information Shows HDG (heading), COG (Course Over Ground), and
SOG (Speed Over Ground).
5 Radar information Shows antenna ID, band width, transceiver type, pulse
width, display range of the connected radar.
6 Significant wave height Shows significant wave height.
7 First wave information Shows wave height, wave direction and wave period for first
wave.
8 Second wave information Shows wave height, wave direction and wave period for
second wave.
9 Software display state Selects the software display state. (Minimize, Maximize
(grayed out, no use), Close from the left)
10 [MENU] Opens/closes the menu.
11 Orientation mode box Selects the orientation mode.
12 Update time box Shows the time of the most recent wave analysis.
13 Camera icon/System informa-
tion box
• Camera icon: Takes a screenshot.
• System information: Shows sea-trial mode*, manual adjustment mode of wave height, and software version.
*: No indication for normal mode.
14 Alert information box Shows active alerts (alert icon and alert message).
While wave analysis is stopped, the PC screen looks like the following depending on the radar
state.
• Radar is in stand-by: "RADAR ST-BY" is displayed at the center of the left and right screens.
• Radar is disconnected: "NO RADAR" is displayed at the center of the left and right screens.
When the wave analysis contains an error, the message "Wave analysis is not available." appears
at the center of the left screen.
3
Page 9
1. OPERATIONAL OVERVIEW
Own ship icon
Wind speed
Wind direction
Speed over ground
Course over
ground
Heading
Wave periods displayed
in dashed circles
Wave periods displayed
as numerical values
Wave spectrum
Bearing lines displayed
in 16 solid lines
1.2.1 Wave spectrum display area
The 2D analyzed wave spectrum is displayed on the left side of the screen.
• Wave period: The wave periods, or time between waves, appear in the wave spectrum display
area as dashed circles and numerical values (numerical positions are fixed). The wave period
is 15 seconds, 10 seconds, 5 seconds in order of increasing distance to own ship. The farther
away from own ship, the shorter the waves (wind waves), the closer to own ship, the longer the
waves (swells). The periods displayed on the screen are not proportionally displayed due to frequency being used as a distance substitute.
• Wind waves: Waves generated by the wind blowing on the sea.
• Swells: Waves that remain after the waves developed by the wind disappears, or waves that
are detected from a distance and attenuate as they approach.
• Bearing line: The 360° azimuth is divided into 16 with solid lines at 22.5° intervals to make the
waves’ approach easier to understand.
• Wave spectrum: The color of the wave spectrum indicates the relative intensity of the wave on
the wave spectrum display. The intensity of the wave increases in order of dark blue, light blue,
light green, dark green, orange, yellow, red.
• Own ship icon: The own ship icon is displayed at the center of the screen.
4
Page 10
1. OPERATIONAL OVERVIEW
Own ship icon
Bearing lines displayed
in four solid lines
Display range
Radar echo
Pulse width
Antenna ID, Band width,
Transceiver type
First wave information
Second wave information
Significant
wave height
“
***
” appears when there is no calculation data.
- Height: Wave height
- Direction*: Wave direction
- Period: Wave period
*: °T for North Up mode,
°R for Head Up mode
1.2.2 Radar echo display area
The radar echo for wave analysis from the specified radar is displayed on the right side of the
screen.
• Bearing line: The 360° azimuth is divided into four with solid lines at 90° intervals to make the
direction easier to understand.
• Radar echo (for the wave analysis): The absolute intensity of the radar reflection from the wave
increases in order of dark blue, light blue, light green, dark green, orange, yellow, red.
• Own ship icon: The own ship icon is displayed at the center of the screen.
1.2.3 Significant wave height, wave information
The significant wave height and wave information are displayed at the bottom of the screen.
• [Significant]: Shows the significant wave height. The significant wave height is a statistical value
obtained by averaging the top 1/3 highest waves when observing the specified area. Although
its value is different from the maximum value or the simple average value, it is the closest value
to the wave height visually observed by a skilled observer.
• [1st Wave], [2nd Wave]: Among the observed waves, the two most outstanding waves are selected and assigned as [1st Wave] and [2nd Wave] for reference. There is no distinction made
between wind waves and swells for this selection.
5
Page 11
1. OPERATIONAL OVERVIEW
The head-up mode is a display in which the
line connecting own ship and the top of the
display indicates own ship's heading.
North bearing is maintained at the top of the
screen. The heading line changes its direction according to the ship's heading.
North marker
Heading line
Heading line
North marker
North UP
Head UP
The reliability (degree of trust) of the analysis result of the first or second wave is indicated with a
numerical index of 0 to 100. The character color changes according to the degree of trust.
Note: It is recommended to use the analysis result with a reliability of “High” or “Middle”. For “Middle”, take care of the precision.
Reliability
High 70 or more White The sea weather condition is suit-
Middle 45 or more and
Low Less than 45 Orange The sea weather condition is not
Index*
(default)
less than 70
Color/display example Description
able for wave analysis. The precision and accuracy of the analysis
result is high.
Yellow The sea weather condition is
slightly unsuitable for wave analysis. The precision of the analysis
result is low and there is variation,
but the accuracy is great.
suitable for wave analysis. The
precision and accuracy of the analysis result is low.
*: Set these values in the [INITIAL SETTINGS] menu at installation.
1.3 Keyboard Operations
This software uses the Tab key, Enter key and Space key in the following manner:
• Tab: Cycles through [MENU] → Orientation mode box → Camera icon → Alert information box
→ … in order.
• Enter/Space: Confirm selection.
1.4 Orientation Mode
Click the orientation mode box at the top right position of the screen to switch between North UP
mode and Head UP mode.
6
Page 12
1. OPERATIONAL OVERVIEW
Shown in the sea-trial mode.
(No indication in the normal mode.)
Shown in yellow when setting the wave height analyzing
mode to Manual. (No indication for Auto mode.)
Program version no. of this software.
㻜㻝㻚㻜㻝
1.5 Analysis Update Time
The time (UTC) of the most recent wave analysis is displayed at the bottom right of the screen.
LAST UPDATE
01/JAN/2019 15:10:27
When wave analysis is not done immediately after software startup or date and time information
is not input, the indication appears as "**/***/**** **:**:**".
01/JAN/2019 15:10:27
Month
Day
Year
Hour
Second
Minute
1.6 Menu Overview
1. Click [MENU] to open the menu.
1. SYSTEM MONITOR
2. ALERT STATUS
3. INITIAL SETTINGS
2. Click the desired menu item to highlight it.
Menu item Description
[1. SYSTEM MONITOR] Opens the system monitor window.
[2. ALERT STATUS] Opens the alert status window.
[3. INITIAL SETTINGS] Opens the initial settings window (for qualified technician, required
the password).
3. Click [MENU] to close the menu.
1.7 How to Take a Screenshot of a Display Screen
Click the camera icon at the bottom right of the screen to take a screenshot. Screenshots are
saved in the folder “C: \ Users \ User name \ Documents \ FURUNO \ WaveAnalyzer \ screenshot”.
When the folder becomes full, the message "Storage size is full." appears. Delete unnecessary
data to make room. Also, you can not take a screenshot while the menu is open.
1.8 System Information
The system information is displayed at the bottom right of the screen.
7
Page 13
1. OPERATIONAL OVERVIEW
x.x
Re-install the software.
Uninstall the software.
1.9 How to Update the Software
Make sure the software is closed before attempting to update the software. Also, log into the PC
with administrator privileges before updating the software.
1. Turn the PC on.
2. Insert or connect the update media to the PC. Consult your local dealer regarding the media.
3. Double-click [WaveAnalyzer_setup].
4. Double-click [WaveAnalyzerInstaller msi]. The following screen appears.
Note: When running the installer with the same version as the current software, the following
screen appears. Click [Cancel] to finish the installer and then install the new version software.
5. Click [Next].
8
Page 14
1. OPERATIONAL OVERVIEW
Software for
wave analyzer
Operator’s
manual
Firewall-related software
6. Click [Next]. To change the installation folder, click [Browse] and select the folder before clicking [Next].
7. Click [Next] to start the installation.
Note: If the dialog box [UserAccountControlSettings] appears, click [Yes] to start the installation.
When the installation is completed, the dialog box shown below appears.
8. Click [Close] to finish. The shortcut icons for the manual and related software are created on
your desktop.
9
Page 15
2. PRINCIPLE OF OPERATION,
Wave spectrum Radar echo
HOW TO INTERPRET THE DISPLAY
2.1 Principle of Measurement
This software analyzes sea waves by using the received radar signal. When observing the waves
with the radar, sea clutter echoes appear as stripes.
The amplitude of the sea reflection echo depends on the roughness caused by the wind acting on
the sea reflection. (It is not the height of the wave.) This software obtains multiple echoes, processes the data, and calculates the wave spectrum, wave height, wave direction, and wave period.
2.2 Reliability of Analysis Results
When the sea reflection echoes are displayed with stripes, the analysis results are more reliable.
When the sea reflection echoes are not displayed in stripes (lull, rain), the analysis results are less
reliable.
Example image for high reliability
10
Page 16
2. PRINCIPLE OF OPERATION, HOW TO INTERPRET THE DISPLAY
Wave spectrum Radar echo
Detection
sensitivity
4 sec. 15 sec.
Wave period
: Wave radar (Detection sensitivity
for long period is high.)
: Visual observation (Detection
sensitivity for short period is high.)
The figure below is an example of echo during rainfall. This image is less reliable because no
stripes are visible, that is, the spectrum is broadened and there are no outstanding waves.
Example image for low reliability
Difference for the wave result between this software and visual observation
The waves that can be detected by this software are gravity waves with a wave period of 4 seconds or more. The waves with a short period, that is, the waves blown by the wind may not be
observed. Therefore, the visual wave direction and the analysis result may be different (see the
figure below).
11
Page 17
3. ALERTS
A
Alert Status
Close
15/JAN/2019 17:22
15/JAN/2019 16:37
15/JAN/2019 10:51
07 INT-SW status error.
05 Radar communication error.
03 Ship speed data error.
Date and time
of alert
Alert number
and message
Alerts are displayed at the bottom right of the screen, with the alert icon, alert number, alert message, and time of alert.
Alert number
lert icon
The [Alert Status] displays the number and message of triggered alerts, including the time and
date triggered.
05 17:20
Rada comm...
Alert message
Time of alert*
*: “
” appears when
**:**
there is no time input.
How to display the [Alert Status] screen
1. Click the alert icon to display the [Alert Status] screen. You can also display the [Alert Status]
screen by clicking [MENU] – [2 ALERT STATUS].
2. Click [Close] to close the [Alert Status] screen.
For details, see "ALERT LIST" on page AP-2.
The alerts currently active are shown on the screen. When there is no alert, "No Alert" appears
at the center of the screen.
12
Page 18
4. TROUBLESHOOTING
4.1 Troubleshooting
This section provides simple troubleshooting procedures which the user can follow to restore normal operation. If you cannot restore normal operation, contact your dealer.
Problem Possible cause Remedy
Software does not start. The components (VisualC++
runtime) are not installed.
The USB dongle is not inserted. Check if the USB dongle is firmly in-
Software is already open. Since this software can not start mul-
Pictures are not updated
or freeze.
Reliability of analysis result remains “low”.
The software does not
start if you click [Retry] after a USB dongle authentication error occurs.
The COM port does not
open.
The memory for CPU or GPU is
insufficient.
The sea weather conditions do
not meet the measurement conditions of the wave radar.
GPU is highly loaded (high temperature, power saving mode).
The radar pulse width is not appropriate.
The USB dongle is not recognized.
The PC does not recognize the
COM port.
The COM port is in use by other
software.
Install the supplied file “setup.exe”.
serted. The LED in the dongle lights
red when the dongle is recognized
correctly.
tiple times, quit the software that is already activated.
• Restart the software.
• If there is software running other
than this software, exit it.
In case of rainfall, switch to an S-band
radar.
• Check if power is supplied to the
PC (the battery is not running).
• Check if the vents on the PC are
blocked.
Change the radar pulse width to S1
since S1 is the highest in measurement accuracy.
Restart the software.
• Check if the port is recognized by
the device manager.
• Check the COM port driver.
• Close if the COM port is opend by
another software.
• Quit the other software.
• Restart the PC.
13
Page 19
4. TROUBLESHOOTING
Click [<].
Click [>].
Page 1
Page 2
Page 3
Click [<].
Click [>].
SYSTEM MONITOR 1/3
Close
>
Wave Analyzer software version: 0359495-01.01
IP address: 192.168.31.226
Subnet mask: 255.255.255.0
Host name: RWV001
Primary Radar No.: RAS001
Radar ANT Speed: 24rpm
Wave height analyzing mode: Auto
SYSTEM MONITOR 2/3
Radar connection: OK(ANT1)
Sensor data
DATE: OK $GPZDA,042843.40,02,04,2019,00,00*67
COG/SOG: OK $GPVTG,30.0,T,0.0,M,10.0,N,10.0,K,A*10
POS: OK $GPGNS,042843.40,3442.019,N,13521.735,E,DDD,00,0.0,0.0
WIND: OK $WIMWV,0.0,T,10.0,K,A*11
HDG: OK
Pulse width < M2: OK (M1)
INT-SW status: OK
Data accurency: 1st OK(41) 2nd OK(39)
Storage size: OK
Dongle: OK
SYSTEM MONITOR 3/3
PC system information
OS: Microsoft Windows 10 Home 64-bit (10.0.15063, Build 17134)
Processor: Intel(R) Core(TM) i7-7700HQ CPU @ 2.80GHz
Memory: 8192MB RAM
GPU: NVIDIA GeForce GTX 1050
OpenGL version: 4.5.0 NVIDIA 376.74
Display memoty: 2048MB RAM
Display resolution: 1920 X 1080
<
Close
>
<
Close
4.2 System Information
The system information is displayed from the menu.
1. Click [MENU] to open the menu.
2. Click [1 SYSTEM MONITOR].
The results for items which fail the system monitor test appear in yellow text with the indication
"NG" (No Good).
14
Page 20
4. TROUBLESHOOTING
The following table lists descriptions for each item.
Item Description
Wave Analyzer software
Shows program number for this software.
version
IP address Shows the IP address for the wave analysis PC.
Subnet mask Shows the subnet mask for the wave analysis PC.
Host name Shows the host name for the wave analysis PC.
Primary Radar No. Shows the host name for the primary connected radar. See the in-
stallation manual for how to set this item.
Radar ANT Speed Shows the antenna speed of the connected radar.
Wave height analyzing mode Shows the wave height adjustment mode.
Radar connection Shows the radar connection status (OK or NG) and the number of
the connected radar.
DATE Shows the input status of the date information (OK or NG) and sen-
tence used.
COG/SOG Shows the input status of the speed information (OK or NG) and
sentence used.
POS Shows the input status of the position information (OK or NG) and
sentence used.
WIND Shows the input status of the wind information (OK or NG) and sen-
tence used.
HDG Shows the input status of the heading information (OK or NG).
Pulse width < M2 Shows the pulse width of the connected radar and if it is less than
M2 (OK or NG).
INT-SW status Shows the interswitch status of the connected radar (OK or NG).
For NG, shows the number of the slave radar.
Data accurency Shows the degree of trust for the wave analysis result for the first
or second wave.
Reliability
High
Middle
Low
Indication (Range)
OK䠄70 to 100
OK䠄45 to 69
NG䠄0 to 44
䠅
䠅
䠅
Character color
White
Yellow
Orange
It is recommended to
use analysis results
with the indication “OK”
(see subsection 1.2.3).
Storage size Shows if there is enough free space in the PC for wave analysis
(OK or NG).
Dongle Shows if the dongle has errors (OK or NG).
• Normal mode: OK
• Sea-trial mode: OK (SEA-TRIAL MODE)
OS* Shows the OS information for the wave analysis PC.
Processor* Shows the CPU information for the wave analysis PC.
Memory* Shows the memory information for the wave analysis PC.
GPU* Shows the GPU information for the wave analysis PC.
OpenGL version* Shows the OpenGL information for the wave analysis PC.
Display memory* Shows the video memory information for the wave analysis PC.
Display resolution* Shows the display resolution for the wave analysis PC.
*: "****" appears when there is no data input.
3. Click [Close] to close the menu.
15
Page 21
APPENDIX 1 MENU TREE
Click [MENU].
1. SYSTEM MONITOR (Opens the system monitor window.)
2. ALERT STATUS (Opens the alert status window.)
3. INITIAL SETTINGS (For a qualified technician)
AP-1
Page 22
APPENDIX 2 ALERT LIST
The following table shows the alerts in this software.
No. Text Meaning Remedy
01 Date and Time data error. No data for the date and time. Check if the date and time
signal is input.
02 GPS data error. No positioning data. Check if the GPS signal is in-
put.
03 Ship speed data error. No speed data. Check if the speed signal is
input.
04 Wind sensor data error. No wind data. Check if the wind signal is in-
put.
05 Radar communication error. Can not connect the radar. Check the network connec-
tion.
06 Pulse width error. The pulse width of the con-
nected radar is more than M2.
07 INT-SW status error. The interswitch of the con-
nected radar is set to ON.
08 Storage size is full. The capacity for the result file
is full. The space is less than
10 GB. Or, can not recognize
the destination where to save
data.
09 COM Open error. Can not open the COM port
for the serial output.
10 GYRO data error. Gyrocompass data is unavail-
able.
Set the pulse width from S1 to
M1.
Set the interswitch to OFF.
Delete unnecessary data
from the folder to make room.
Check the connection of the
COM port.
Check if the Gyrocompass
data is input.
AP-2
Page 23
APPENDIX 3 SERIAL OUTPUT DATA
Data bit
Start
bit
Stop
bit
D0 D1 D2 D3 D4 D5 D6 D7
$PFEC,RAwv1,x,hhmmss.ss,xx,xx,xxxx,x,x,x,x.x,x,x.x,a,x.x,hhhh,a,x.x,x.x*hh<CR><LF>
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17
1. Block number (0 to 9)
2. Wave analysis last update time (UTC) (000000 to 235959)
3. Wave analysis last update day (UTC) (01 to 31)
4. Wave analysis last update month (UTC) (01 to 12)
5. Wave analysis last update year (UTC) (0000 to 9999)
6. Radar number (1 to 8)
7. Radar type (0=Xband Magnetron 2=Sband Magnetron 3=Sband SSD)
8. Pulse type (0=S1 1=S2 2=M1 3=M2 4=M3 5=L)
9. Antenna rotation (RPM) (0 to 99.9)
10. Wave analysis mode (0=Normal 1=Sea Trial)
11. Average time of wave results (sec) (0 to 9999)
12. Orientation reference (N=North)
13. Number of RAwv2 in the same block (0 to 10)
14. System error status (0000 to FFFF)
15. Wave height measurement mode (A =auto mode M=manual mode)
16. Wave calculation parameter 1 (0 to 100)
17. Wave calculation parameter 2 (0 to 100)
The wave analyzer outputs the data of the wave analysis result by serial communication.
• RAwv1 and RAwv2 are output as one data block. The number of RAwv2 contained in the same
block is determined by the number of waves analyzed. For example, if significant wave, 1st
wave, and 2nd wave were analyzed, the number of RAwv2 would be three.
• The data output cycle is shown in the table below.
Radar antena rotation Cycle
24 rpm 80 seconds
36 rpn 54 seconds
42 rpm 46 seconds
Serial output setting
Setting items Port Remarks
Baud rate 4800, 9600, 19200, 38400 (bps) Set in the [3. INITIAL SETTINGS] menu.
Start bit 1 bit –
Data bit 8 bit –
Stop bit 1 bit –
Parity none –
Flow control none –
Data sentences
PFEC, RAwv1 – Wave Analyzer setting information
AP-3
Page 24
PFEC, RAwv2 – Wave analysis results
$PFEC,RAwv2,x,x,x.x,x.x,x.x,x.x,A,x.x,A*hh<CR><LF>
1 2 3 4 5 6 7 8 9
1. Block number (0 to 9)
2. Wave number (0=Significant wave 1 to 9=1st to 9th wave)
3. Wave height (m) (0 to 99.99)
4. Wave direction (degree) (0 to 359.99)
5. Wave period (sec) (0 to 99.99)
6. Wave height reliability (0 to 100)
7. Wave height status (A=data valid V=data invalid)
8. Wave direction and period reliability (0 to 100)
9. Wave direction and period status (A=data valid V=data invalid)
APPENDIX 3 SERIAL OUTPUT DATA
AP-4
Page 25
APPENDIX 4 SEA-TRIAL MODE
(For WV-100ST)
For sea-trial mode, the result and spectrum files can be output.
Result file
The file size is a maximum of 1 MB. When the size is over 1 MB, a new file is created. Approximately 56 hours of data can be saved per 1 MB, in the folder “C: \ Users \ User name \ Documents
\ FURUNO \ WaveAnalyzer \ result \ YYYYMMDD”. The following data are saved for each analysis:
Item Unit Description
DATE_TIME – ZDA sentence time
LATITUDE deg Latitude, instantaneous value, south latitude (-90
to +90), north latitude
LONGITUDE deg Longitude, instantaneous value, west longitude
(-180 to +180), east longitude
HEADING deg Heading, instantaneous value
COG deg COG, instantaneous value
SOG deg SOG, instantaneous value
TRUE_WIND_DIRECTION deg True wind direction (Nup), average for one scan
TRUE_WIND_SPEED m/s True wind speed, average for one scan
MEAN_TRUE_WIND_DIRECTION deg True wind direction (Nup), average for one analy-
sis
MEAN_TRUE_WIND_SPEED m/s True wind speed, average for one analysis
ANT_NUM – Antenna number
ANT_MODEL – Antenna model
ANT_ROTATION RPM Antenna rotation speed
PULSE_INFO – Pulse information
RANGE_INFO – Range information with unit
WAVE_HEIGHT m Total wave, wave height, instantaneous value
2
M0_TOTALWAVE
DIRECTION_TOTALWAVE deg Total wave, wave direction, instantaneous value
PERIOD_T01_TOTALWAVE sec Total wave, wave period T01, instantaneous value
PERIOD_T02_TOTALWAVE sec Total wave, wave period T02, instantaneous value
SIGNIFICANT_WAVE_HEIGHT m Significant wave height
MEAN_M0_TOTALWAVE
MEAN_DIRECTION_TOTALWAVE deg Total wave, wave direction, average
SIGNIFICANT_WAVE_PERIOD sec Significant wave period
MEAN_PERIOD_T01_TOTALWAVE sec Total wave, wave period T01, average
MEAN_PERIOD_T02_TOTALWAVE sec Total wave, wave period T02, average
WAVE_HEIGHT_1stWAVE m First wave, wave height, instantaneous value
M0_1stWAVE
DIRECTION_1stWAVE deg First wave, wave direction, instantaneous value
PERIOD_1stWAVE sec First wave, wave period, instantaneous value
PERIOD_T01_1stWAVE sec First wave, wave period T01, instantaneous value
PERIOD_T02_1stWAVE sec First wave, wave period T02, instantaneous value
m
m
m
Total wave, zero moment, instantaneous value
2
Total wave, zero moment, instantaneous value
2
First wave, zero moment, instantaneous value
AP-5
Page 26
APPENDIX 4 SEA-TRIAL MODE (For WV-100ST)
2018/10/10 18:15 Period/Direction
0.04 24.999998
0.05 20
0.06 16.666666
0.07 14.285714
0 10 20 30
0.000001
0.000001 0.000001 0.000001
0.000003 0.000003 0.000004 0.000004
0.000007 0.000007 0.000007 0.000007
0.00001 0.00001 0.000011 0.000011
.....
.....
.....
.....
.....
Date and time
Degree (deg)
Frequency (Hz) Wave period (s)
Item Unit Description
RELIABILITY_1stWAVE – First wave, reliability, instantaneous value
MEAN_WAVE_HEIGHT_1stWAVE m First wave, wave height, average
MEAN_M0_1stWAVE
MEAN_DIRECTION_1stWAVE deg First wave, wave direction, average
MEAN_PERIOD_1stWAVE sec First wave, wave period, average
MEAN_PERIOD_T01_1stWAVE sec First wave, wave period T01, average
MEAN_PERIOD_T02_1stWAVE sec First wave, wave period T02, average
MEAN_RELIABILITY_1stWAVE – First wave, reliability, average
WAVE_HEIGHT_2ndWAVE m Second wave, wave height, instantaneous value
M0_2ndWAVE
DIRECTION_2ndWAVE deg Second wave, wave direction, instantaneous val-
PERIOD_2ndWAVE sec Second wave, wave period, instantaneous value
PERIOD_T01_2ndWAVE sec Second wave, wave period T01, instantaneous
PERIOD_T02_2ndWAVE sec Second wave, wave period T02, instantaneous
RELIABILITY_2ndWAVE – Second wave, reliability, instantaneous value
MEAN_WAVE_HEIGHT_2ndWAVE m Second wave, wave height, average
MEAN_M0_2ndWAVE
MEAN_DIRECTION_2ndWAVE deg Second wave, wave direction, average
MEAN_PERIOD_2ndWAVE sec Second wave, wave period, average
MEAN_PERIOD_T01_2ndWAVE sec Second wave, wave period T01, average
MEAN_PERIOD_T02_2ndWAVE sec Second wave, wave period T02, average
MEAN_RELIABILITY_2ndWAVE – Second wave, reliability, average
m
m
m
2
First wave, zero moment, average
2
Second wave, zero moment, instantaneous value
ue
value
value
2
Second wave, zero moment, average
Spectrum file
The file size is a maximum of 1 MB. When the size is over 1 MB, a new file is created. Approximately 2.5 hours of data can be saved per 1 MB, in the folder “C: \ Users \ User name \ Documents
\ FURUNO \ WaveAnalyzer \ spectrum \ YYYYMMDD”.
File example
AP-6
Page 27
FURUNO
WV-100/100ST
SPECIFICATIONS OF WAVE ANALYZER
WV-100/100ST
1 SYSTEM REQUIREMENT
1.1 OS Windows® 10 Pro/Home
1.2 CPU Intel Core i5 or later
1.3 GPU NVIDIA GeForce GTX1050, 384 cores, VRAM 2GB or more
1.4 SSD/HDD 128 GB or more
1.5 Memory capacity 4 GB or more
1.6 Interface LAN, USB 2 ports or more (for dongle and serial communication)
2 MONITOR (USER SUPPLY)
2.1 Display resolution SXGA/UXGA/FHD
2.2 Language UK/USA
3 MEASURING RANGE
3.1 Wave height 0.10 to 15.0 m
3.2 Wave period 4.00 to 16.00 s
3.3 Wave direction 0.00 to 359.99°
3.4 Wave component 2 max.
3.5 Bearing -140 to +140° (from the bow)
3.6 Distance 150 to 1200 m
4 SEA WEATHER CONDITIONS
4.1 Sea state code 3 min. (wave height: 0.5 m or above)*
4.2 Beaufort scale 3 min. (wind speed: 3.4 m/s or above)*
4.3 Precipitation 1 mm/h or less for X-band
5 mm/h or less for S-band
4.4 Sea depth 0.5 times or more of the measured wavelength
*: The measurement may be lowered when the conditions are not enough.
**: The calculable rainfall changes with wave height and wind speed.
5 INTERFACE
5.1 Number of port
LAN 1 port: Ethernet 100Base-TX
RS-232C 1 port: USB/RS-232C converter available
5.2 Data sentences
LAN (input) WMV
PFEC (output) RAwv1, RAwv2
5.3 Sea trial mode Analysis data file output (WV-100ST only)
SP - 1 E3652S02A
190730
Page 28
(Elemental Chlorine Free)
The paper used in this manual
is
elemental chlorine free.
・ 機器の修理・使用方法等に関するお問い合わせは、お買い上げの販売店・代理店、最寄りの
当社支店・営業所あてへお願いします。
・
FURUNO Authorized Distributor/Dealer お問い合わせは
本書の無断複写複製(コピー)は特定の
場合を除き、当社権利侵害になります。
Pub. No. OMC-36181-A1
( ETMI) WV-100/WV-100ST
Printed in Japan
A
: JUN. 2019
A1
: AUG. 1, 2019
00019657810
Loading...