M1
PASSTHROUGH DISHWASHER
Operator Manual
Foreword
User documentation
Please read this manual and keep it in a safe place for future reference.
WARNING
Before installation and commissioning, you must read the safety instructions and
warnings carefully and all the warning labels attached to the equipment.
IMPORTANT
Failure to comply (even partially) with the instructions given in this manual will
invalidate the product warranty and relieves the manufacturer of any responsibility.
IMPORTANT
The alteration of machine operation, design or the replacement of parts not
approved by the manufacturer may void warranties and approvals.
Warranty Registration
Complete the information below for quick reference.
Model Number_______________Serial Number________________
Purchased from______________ Date of Purchase______________
If you require further information regarding authorised service providers or
recommended detergent suppliers in your region, or have any other queries, please
do not hesitate to contact us.
IMPORTANT
TO VALIDATE YOUR WARRANTY, PLEASE COMPLETE AND
RETURN THE WARRANTY REGISTRATION CARD WITHIN 30
DAYS FROM THE DAY OF PURCHASE.
Information supplied in this manual is copyright. No part of this work may be reproduced
or copied in any form or by any means, electronic or mechanical without the express
permission of the author / publisher. Document subject to change without prior notice.
!
!
!
Operator Manual M1-3(S)
Safety Instructions
WARNING
Equipment contains dangerous voltages and can be hazardous if installed or
operated incorrectly. Non-compliance with Warnings or failure to follow the
instructions contained in this manual can result in loss of life, severe personal
injury or serious damage to property.
Installation
♦ Use qualified, skilled personnel
♦ Follow installation instructions
♦ Connect to correct voltage and supply current
♦ Provide fully accessible Electrical Isolation Switch
Training and Supervision
♦ Read and Understand the Operating instructions
♦ Train all staff
♦ This appliance is not intended for use by young children, who must be
supervised to ensure they do not play with the appliance
♦ This appliance is not intended for use by infirm persons without supervision
♦ This appliance is not intended for use as a stepladder
Hot Surfaces
♦ Be aware some surfaces can be hot
Chemicals
♦ Commercial dishwashing detergents are hazardous
♦ Read and follow the safety information found on the labels of detergent
containers and Material Safety Data Sheets
♦ Handle with care
♦ Use protective eyewear and clothing if decanting containers
Hot Water
♦ Door safety switches are designed for emergency use only
♦ Wait for the green cycle light to go out before opening the door
♦ Wash water is 60°C and contains caustic detergent so DO NOT put hands
in wash water
Cleaning
♦ DO NOT hose down the machine or splash water over the exterior
♦ Watch for broken glass etc when cleaning the inside of the machine
Operator Manual M1-3(S)
Installation
WARNING
Installer must be suitably qualified and ensure compliance with all local codes and
standards including AS/NZS 3500.1.
Failure to comply even partially with installation instructions may void the
warranty.
Positioning
Unpack machine, check for damage and complete delivery. Install machine on
sound waterproof self-draining floor and use adjustable feet to level machine.
Allow room for detergent to one side of machine or in adjacent cupboard. 20litre
container requires about 450H x 250W x 350D, but smaller containers are available
from many suppliers.
Benchwork
Refer Bench Details drawing.
For corner installations front of machine must face
to the left of the corner. In corner installations high or angled bench return off
wall may clash with door handle. Level and secure machine and benches. Adjust
to ensure smooth travel of rack through machine.
Hot Water
Water temperature 65°C ± 5°C
Connection 20 mm (3/4” BSP) male
Flow rate minimum 20 litres per minute
Hot water consumption 3 litres per cycle approximately
Backflow prevention Vacuum Breaker fitted standard
Pressure 200-400 KPa = 30-60 Psi.
Above this range fit pressure limiter. Don’t use small diameter plastic supply lines.
FLUSH supply line before connection. Poor quality supply or excessive water
hardness may affect performance or damage machine – filtration and/or softening
is recommended.
Waste
40 mm gravity drain – refer point B on installation diagram – run waste directly
behind the machine, through knockouts in side panels or through hole in base.
Power
Electrical supply required is single phase 230V 22A 50Hz, permanently wired via
wall switch mounted adjacent to machine. Machine may also be installed on a 15A
single phase circuit (with reduced rinse heating). For this requirement remove
double adaptor and Red 0.75 wire from rinse over-temperature thermostat and
reconnect Red 1.5 mm wire to the over-temperature thermostat.
Detergent
Insert detergent pump inlet hose into container of commercial low foam detergent.
Open machine door and switch machine on. Press and hold detergent prime
switch behind front cover until chemical flows into machine.
Installation Checklist
Complete attached Installation Checklist to ensure machine is installed and
running correctly, and operator is familiar with operating procedures.
!
Operator Manual M1-3(S)
Operator Manual M1-3(S)
Operator Manual M1-3(S)
Installation Checklist
CHECK OK / NOTES
Delivery
Supplied complete no transit damage
Position
Level and stable on sound, waterproof, self draining floor
Water
Isolator valve fitted Accessible, all fittings sound, no leaks
DCVs fitted (Washtech only) Correct direction
Temperature 65 ± 5°C
Flow rate Minimum 20 litres per minute
Pressure 200-350 kpa, limiter fitted if above this range
Booster fitted if below this range
Cold water when required Pressure not above 350 kpa
Hardness Filter or softening if required
Power
Isolating switch Fitted, functional and accessible
Supply as specified Voltage, current, circuit breaker
Waste
Usually 40 mm Sound, no leaks
Air gap on pumped drain Very important GLV and UD models
Chemicals
product name container no leaks primed conc.OK
Detergent
Rinse Aid
Machine operation
Run several cycles
Confirm correct operation Including correct fill levels
Operator training
Confirm Operator has copy of Operator Manual and is familiar with procedures
Start-up Model / Serial
Pre-rinse and racking Owner
Machine operation Location
Drain Technician
Clean Date
Shut-down Signed
Operator Manual M1-3(S)
Dishwashing Procedures for best results
Note: these are general instructions to assist in getting the best performance from Starline dishwashers – some
comments and / or illustrations may not apply to every unit.
Installation
Read the Operator Manual. Correct installation, including an adequate supply of
water at the correct temperature and pressure is essential for effective operation of
your machine. Refer installation instructions for details. Drain hose outlet height
is important on some models. Always install on a sound self-draining floor.
Water softening is recommended in hard water areas - especially for glasswashing.
Pre-rinsing
Pre-scraping of dishes is required by hygiene regulations.
The best method is to pre-rinse with a pre-rinse spray unit or alternatively by scraping or dunking in water.
Cutlery Procedures
Pre-soak cutlery in warm water, preferably containing cutlery
pre-soak compound - refer your chemical supplier.
Do not overfill cutlery containers. Cutlery should be loose with
handles down. Sort after washing rather than before. Cutlery
of only one type nests together and obscures wash water.
Racking Procedures
Do not overload racks, minimize the overlap
of crockery. Cycle times are short and water
consumption per cycle low - so there is no
advantage in overloading racks.
Cycle Times
For multi-cycle machine use the longest
cycle whenever possible. Note that water
consumption does not increase with
longer cycles. Only choose shorter, faster
cycles when necessary.
Detergent
Use of correct type and quantity of low foaming commercial grade
detergent is essential to the performance of the machine. We
strongly recommend that you use a professional dishmachine
chemical supplier - and will be pleased to recommend a supplier in
your region. Discuss with them the use of cutlery pre-soak
solution, detergent and drying agent.
Operator Manual M1-3(S)
Dishwashing Procedures for best results
Drying
Single tank commercial dishwashers do not have a drying
cycle. However, the machines do rinse at high temperatures
which promote fast drying particularly when drying agents are
used. We recommend prompt removal of the rack from the
machine - leave the rack on the bench for 2 to 3 minutes
before emptying. This time will be reduced with correct use
of drying agent (rinse fluid) which reduces water surface
tension and allows water to drain quickly from washware.
For advice on drying agents and injectors refer to your
chemical supplier.
Daily Cleaning
It is essential that the machine is drained and cleaned at the end of each day. Drain
the machine then remove, clean and replace filters as per the operating
instructions. Regularly check the wash and rinse jets and clean them if necessary –
see below.
Regular Cleaning
Remove scrap trays1 and wash pump inlet filter2, where
fitted, and rinse or brush clean.
Remove wash and rinse arms by undoing the central
thumbscrews3. If necessary, remove the end cap screws4
from the wash arms and the end screws5 from the rinse
arms and flush the arms with water and/or use a toothpick or
paperclip to clear jets.
Note: arms and filters vary with model and may appear
different from this illustration e.g. those models with plastic
wash arms have removable jets for ease of cleaning.
Regular Servicing
Regular servicing of the dishwasher is absolutely essential to
keep the machine in top working condition and obtain the
best performance.
Please contact Washtech or your Authorised Service
Provider to organize regular servicing of the dishwasher discuss a Preventative Maintenance Agreement for optimum
performance and long machine life.
Note: these are general instructions to assist in getting the best performance from Starline dishwashers – some
comments and / or illustrations may not apply to every unit.
Operator Manual M1-3(S)
Operating Instructions
Start up
Fit drain upstand, wash pump filter,
scrap tray and shut door.
Turn wall and machine power
switches on.
Power light glows red and machine
fills automatically.
Wash Ready light glows amber when
wash tank is ready.
Rinse Ready light glows amber when
the machine is up to required
temperature and ready to run.
Operation
Load rack into machine and close
door to start the machine.
Cycle light glows green during
2 minutes cycle of operation.
When Cycle light goes out, cycle is
complete.
Open door and remove rack.
After removing rack from machine, DO NOT shut door as machine
will start up again.
NOTE: Machine will not operate unless Ready lights are on.
Shut down every night
Turn machine and wall power switches off.
Remove drain upstand to drain wash tank.
Remove scrap tray and wash pump filter and rinse clean.
Replace drain upstand, filter and scrap tray.
Operator Manual M1-3(S)
Operator Manual M1-3(S)
Warranty
WASHTECH warrants that new STARLINE products are free from defects in material or
workmanship for a period of one year from the date of purchase.
EXTENT OF WARRANTY
Washtech shall repair or, at its discretion, replace any part of the machine found to be defective.
The labour for the repairing or the replacement of defective parts shall be provided during normal
office hours at no cost to the user.
Washtech shall not otherwise be liable for any other loss or damage arising out of any person’s use
or inability to use the machine.
Washtech shall not be liable for the cost of work done outside normal office hours, and for travel
costs outside regional centres.
Washtech shall not be liable for detergent related issues, including detergent pump adjustment or
squeeze tube replacement, drain pump blockages and other related damages.
CONDITIONS OF WARRANTY
This warranty shall not be binding on Washtech unless the warranty registration card is
completed and received by Washtech within 30 days from the date of purchase
This warranty shall be void if:
The equipment has not been properly installed by an authorised Washtech Service Provider.
Persons other than Washtech Service Providers have undertaken repairs or attempts at repair.
The equipment has not been operated and maintained in accordance with the Operator Manual.
Damage has resulted from shipment, handling, fire, water, accident, abuse, detergent equipment
fitted by others or any other event beyond the control of Washtech.
Any defect must be notified to Washtech or its authorised dealer within 30 days of the
discovery of the defect.
IF YOU WISH TO MAKE A WARRANTY CLAIM
First check the things you can do for yourself. Refer to the Operator Manual provided to ensure
that the machine is correctly installed and that you are familiar with its operation. If a service
technician calls and determines that the equipment is not defective you will be charged with the
cost of the call-out.
If you need service during the warranty period, first contact the dealer from whom you purchased
the equipment. The Dealer will arrange service by Washtech or an authorised Starline Service
Provider.
If you have a problem contacting your dealer or if your dealer is unable to assist, then please
contact the Service Department, Washtech, telephone 09 829 0923.
When you write or call you will need to provide your name and address, the model and serial
number (refer lower front cover) and the date of purchase so that your warranty claim may be
validated.
Operator Manual M1-3(S)
Notes
Operator Manual M1-3(S)
Loading...