Warmup + Kit Installation Manual

Kit

Installation Guide

+

Contents

2

Components ....................................................

Step 1 - Download the MyHeating App .....................

Step 2 - Install the Boiler Receiver ........................

Step 3 - Mounting ..............................................

Step 4 - Pairing the 4iE to the Boiler Receiver ............

Step 5 - LED Indications ......................................

Step 6 - Control in event of communication error .......

Step 7 - Address setting ......................................

Troubleshooting ...............................................

Technical Specications .......................................

3

5

7

12

15

17

18

19

22

23

Kit for use with the 4iE

Components

Power Base

Stand Boiler Receiver

Power Adapter with 1m

USB Cable

3

+

Kit

Step 1 - Download the MyHeating App

+

The MyHeating app is available for iOS and Android devices via the App Store or Google Play. If
you have not done so already, download the MyHeating app to your tablet or smartphone.

Registration

After the app has been successfully downloaded you will need to set up your MyWarmup
account. The 4iE Device can be registered via the app or by visiting my.warmup.com

Kit for use with the 4iE

Step 1 - Download the MyHeating App

5

+

Kit

Step 2 - Install the Boiler Receiver

+

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

Before making any permanent xtures Warmup recommends progressing through to ‘Step 4 -

Pairing the 4iE & Boiler Receiver’ upon identifying preferred locations for the Boiler Receiver

and Power Base. This will ensure the wireless connection is not subject to range or interference
issues once installed.

IMPORTANT INFORMATION: Installation of the Boiler Receiver should only be carried out by a

qualied electrician. It requires a permanent 230V supply.

The Boiler Receiver should be connected to the central heating fused spur or circuit breaker in
accordance with current wiring regulations such that there is a single point of isolation for all
interconnected devices.

Ensure that multi stranded wires are fully inserted into the terminals and secured tightly. Any
loose strands should be trimmed as they could cause a short-circuit.

This product uses mains voltage electricity and work should only

be carried out by a qualied electrician. Electrical installation

to be in accordance with latest edition of BS7671 Wiring

Regulations and appropriate Statutory Regulations.

!

7

+

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

The Boiler Receiver should be installed in the boilers vicinity. Large metal objects such as the
boiler, hot water cylinder or radiators, should be at least 300mm away from the Boiler Receiver
and not directly between it and the 4iE.

Loosen both screws at
the bottom of the Boiler
Receiver and remove
the backplate.

Fix the backplate to the
wall using xing screws

provided.

Make sure to avoid cables or pipes

which may be buried in the wall

!

8

+

1 2

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

Wiring Diagrams

9

+

1 2 3 4

3

Kit for use with the 4iE

Step 2 - Install the Boiler Receiver (Electrician Required)

After the Boiler Receiver has been wired correctly reattach the front panel to the back plate
and tighten both screws to secure.

Restore power to the
boiler. The LED on the

Boiler Receiver will ash

RED which means it has
to be paired to the Power
Base.

4

10

+

4

Kit

Step 3 - Assembly

+

Kit for use with the 4iE

Step 3 - Mounting

1

2

Remove the 4iE from its
packaging. Loosen both
closing screws located
at the bottom of the
4iE. Separate the front
housing from the back
plate.

Thread the power cable
through the Stand and
connect to the Power
Base from your +Kit.
Clip the Power Base
onto the Stand. Connect
the plug to a wall socket.

For optimal performance the thermostat should be located in an area with good ventilation. It
should not be beside a drafty window/door, in direct sunlight or above another heat generating

device (e.g. radiator or TV).

12

For Stand Mount

+

Kit for use with the 4iE

Step 3 - Mounting

Remove the 4iE from its
packaging. Loosen both
closing screws located
at the bottom of the 4iE
Separate the front
housing from the back
plate.

Drill a hole in the wall
to feed the USB Cable
to your wall socket. Attach
the Power Base from your
+Kit to the wall using the

xing screws provided.

Connect the plug to the
wall socket.

For optimal performance the thermostat should be located in an area with good ventilation. It
should not be beside a drafty window/door, in direct sunlight or above another heat generating

device (e.g. radiator or TV).

13

For Wall Mount

+

1

2

NOTE: For detailed instructions, see online at www.warmupsmart.com/installation

Kit

Setup

+

15

Kit for use with the 4iE

Step 4 - Pairing the 4iE & Boiler Receiver

+

The LED on the Boiler
Receiver will stop

ashing RED to indicate

a successful connection.

Using a device, such as a
paper clip, press the
pairing button, as shown
above, on the Power
Base to begin pairing.

2

Power
button

LED

Pairing Button

3

Attach the 4iE front
face to the Power
Base and tighten both
closing screws.

Before pairing, please make sure the Power Base and Boiler Receiver are powered. The LED on
the Boiler Receiver will ash in RED slowly.

NOTE: If the devices have been paired before, hold the Power button on the Boiler Receiver for 6 seconds
and then continue set up.

1 2 3

Kit for use with the 4iE

Step 4 - Pairing the 4iE & Boiler Receiver

16

+

To check that the system
has been installed
successfully, increase the
air temperature by
setting a temporary
override.

Once the 4iE has
powered up, connect to
your WiFi Network.

The heating indicator
will appear on the 4iE,
the light on the Boiler
Receiver will turn solid
GREEN and your heat
system should now
activate.

overrideWi-Fi

target

Warmup

until

backback acceptaccept

21.0°C 15min

4 5 6

Kit for use with the 4iE

Step 5 - LED Indications

17

+

LED Colour LED Status Meaning

N/A Not lit Paired

Green Lit constantly Relay on

Red Flashing slowly Not paired

Red Flashing quickly Relay o

Red Lit constantly Communication Lost

Relay on

LED

LED Status

Kit for use with the 4iE

Step 6 - Control in event of communications error

18

+

The Warmup +Kit for use with the 4iE has been designed to still provide heating control should
the communication between the Power Base and Boiler Receiver be interrupted.

With the Power Base and Boiler Receiver paired and the thermostat calling for heat, the relay
will be activated and the Boiler Receiver will show a constant green LED indication. If the
communication between the Power Base and Boiler Receiver is lost, the green LED will remain
on the Boiler Receiver for a period of up to 30 minutes.

If communication has not been restored after 30 minutes has expired, the Boiler Receiver will
indicate a communications fault by displaying a red LED ashing quickly.

To activate the relay whilst communication has been lost, press the power button on the Boiler
Receiver once. The LED indicator will change from a constant to quick ashing red.

To de-activate the relay whilst communication has been lost, press the power button on the

Boiler Receiver once. The LED indicator with change from constant red to ashing quickly red.

Once communication has been restored, the LED indicator will change back to constant green
providing the thermostat is calling for heat.

Kit for use with the 4iE

Step 7 - Address setting

19

+

Address Set-up

When using multiple +Kit’s, each Power Base should be set to a unique address to prevent
interference. Use the dip switches on the Power Base to select the unique address. 1

Represents ON (up) and 0 represents OFF (down).

Dip Switches

Address 31

Address 61

Address 53

Address 62

Kit for use with the 4iE

Step 7 - Address setting

+

Address Set-up

20

Kit

Troubleshooting

+

Kit for use with the 4iE

Troubleshooting

Due to the large number of dierent boiler systems and wiring plans in use, Warmup cannot

guarantee compatibility with a particular system. Compatible with Combi and System boilers

with 230VAC, volt-free or low voltage input up to 3A. The boiler manufacturer or manual will
be able to conrm if the boiler is compatible with this.

Is the +Kit compatible with
this heating system?

How do I re-pair the
system?

4iE display is blank

4iE displays “er1 amb”

If the wireless connection is lost the LED on the Boiler Receiver will ash RED. If it does not
auto reconnect, press and hold the power button on the Boiler Receiver for 6 seconds. Remove
the 4iE from the Power Base and using a device such as a paper clip press the pairing button
as shown on page 15. The light on the Boiler Receiver will ash GREEN twice to indicate a
successful connection.

Note: You can manually override the system, should the wireless connection fail by pressing
the power button on the Boiler Receiver as shown on page 17.

1. Check that the display/standby brightness is not on the lowest setting, “0”. To access

display/audio settings rst press the standby button at the bottom of the 4iE. Then press

menu, settings and display/audio settings & display brightness.

2. Verify that power is going to the 4iE. Check that the Power Base is plugged in.

+

22

The system type on initial setup should be set to “Central Heating”. If you are using the

Thermostat with a central heating system you will not have a oor sensor installed. Switch
the Thermostat to air mode

>settings >heating preference >control >air/oor

Dimensions 86 x 86 x 26.5mm

Power Supply 230V AC, 50Hz

Fuse T1.6A, 250V

Maximum Relay Load 3A, 250V

Operational Temperature Range 0°C - 50°C

Operational Humidity Range <95% RH

IP Rating IP40

Technical Specications

Dimensions (Assembled with 4iE face) 120 x 121.4 x 63.3mm

Power Supply 5V DC, 300mA

IP Rating IP30

Operational Temperature Range 0°C - 50°C

Operational Humidity Range <95% RH

Power Base

Boiler Receiver

RF Range (Open Air) Max. 100m

Communication Band 868 MHz

Radio Frequency Standards EN301 489-1 V2.2.0 / EN301 489-3 V2.1.1 /

EN300 220-1 V3.1.1 / EN300 220-2 V3.1.1 /

EN 62479:2010 / EN60950-1:2006/A2:2013

Wireless

23

Contact Us

UK

0345 345 2288

702 & 704 Tudor Estate
Abbey Road
Park Royal
London
NW10 7UW

Warranty

Warmup plc warrants this product, to be free from defects in the workmanship or materials, under normal use and service, for
a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is
determined to be defective, Warmup shall repair or replace it, at Warmup’s option. If the product is defective, please either,

(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or

(ii) contact Warmup. Warmup will determine whether the product should be returned, or replaced.

This warranty does not cover removal or reinstallation costs, and shall not apply if it is shown by Warmup that the defect or
malfunction was caused by failure to follow the instruction manuals, incorrect installation or damage which occurred while the
product was in the possession of a consumer.
Warmup’s sole responsibility shall be to repair or replace the product within the terms stated above.
WARMUP SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS
PRODUCT. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY WARMUP MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO
THE THREE-YEAR DURATION OF THIS WARRANTY.

This Warranty does not aect your statutory rights.

Contact Warmup or visit www.warmup.co.uk for details

Warmup - IM - +Kit - V3.2 2017-11-06

NOTE: This product is in compliance with the essential requirements and other relevant provisions of the RED Directive 2014/53/
EU. The Declaration of Conformity may be consulted by visiting: http://www.warmupsmart.com/declarations-of-conformity/kit­declaration-of-conformity/