Page 1
1 (800) 875-5285
www.WarmlyYours.com
Radiant Floor
Heating Made Easy.
The Prodeso Cable Installation Membrane is
an energy-ecient, radiant heat installation
membrane that minimizes eort while providing
a framework for electric floor heating cable.
Prodeso
Membr ne
a
Install Heat
Wherever You
Need It
Protects Tile
& Stone
Installation
Allows Load To
e Distributed
Evenly
10 Year
Warranty
* Prodeso accessories, installed per instructions, are needed to achieve
waterproofing for your Prodeso Cable Installation Membrane.
Cost & Time
Saving
Installation
Uncoupling
& Crack
Isolation
Minimal
Height
Increase
Polypropylene
Membrane
Naturally
Waterproof*
About the Membrane
The Prodeso Cable Installation Membrane is a
polypropylene uncoupling and crack isolation membrane
with rounded square-shaped reliefs. Its unique design allows
quick and easy installation – in and out in one day, flexibility
to adjust to any room size and requires no waiting. Another
advantage is the low profile that works well for projects
where the new floor is installed directly over the old one. In
addition, this cost- and time-eective heat membrane allows
quick installation of tile and floor heating over a variety of
dicult substrates, such as plywood or concrete slabs or
wherever heat is desired.
The long-lasting Prodeso Cable Installation Membrane
makes it fast and easy to install electric floor heating. There
is no waiting required after installation so you can begin
laying the flooring immediately.
Page 2
1 (800) 875-5285
www.WarmlyYours.com
Installation Overview
Please Note: The substrate must be ready to bear weight, solid,
level and free from all substances like oil and grease that could
compromise the adhesion of the Prodeso Membrane.
Cut the Prodeso Membrane to the desired length and apply the adhesive on the
01
substrate using a notched trowel. Use an adhesive suitable for your subfloor:
Wood & Cement Subfloors: Latex-modified Thinset (ANSI A118.11)
Existing Vinyl Floor: Fast Setting, Latex-modified Thinset (ANSI A118.4 – A118.15)
Anhydrite/Gypsum-Based Underlayment: Unmodified Thinset Mortar (ANSI A118.1)
Lay the previously cut roll over the wet adhesive.
02
Press the membrane evenly with a plaster trowel float, making sure to check
03
for coverage. In case of partial coverage, increase the amount of adhesive.
Lay the nex t sheet of the membrane, making sure to align it with the previous
one without overlapping. Align the square reliefs. To protect the membrane
04
against damage or detachment from the support, it is recommended to use
walking boards.
Prodeso
Membr ne
a
Tiles can be immediately laid after the installation of the heating cables. Use
the flat side of the trowel to fill with an unmodified thinset in the cavities of the
05
membrane and apply the same to the tile.
Carefully lay the tiles and press them on the layer of adhesive. If a thin layer of
skin has formed, remove it and apply it again. Occasionally remove and check
06
some tiles to ensure full back coverage.
Available Sizes
SKU Dimensions Sq. Ft.
TC-MEM-BL-054 3.3 ft. x 16.4 ft. 53.8 $159.00 $209.00
TC-MEM-BL-162 3.3 ft x 49.2 ft. 161.5 $399.00 $529.00
TC-MEM-BL-SH39X29 3.3 ft. x 2.4 ft. 7. 9 $25.00 $34.00
Appearance Polymeric Membrane
Color White / Cyan Blue
Shelf life 24 months in dry
environment avoiding
direct sunlight and heat
sources
Total thickness ≈ 7/32 in. (5.6 mm)
Width ≈ 3.37 ft.
Weight of non-woven PP ≈ 16 oz/ft2
Weight of PP sheet ≈ 2.46 oz/ft2
Rounded square shaped reliefs number ≈ 95/ft2
Crack – Bridging Ability ≥ 3/64 in.
Working temperature range -40° F / +176° F
-40° C / +80° C
MSRP USMSRP
CA
Page 3
1 (800) 875-5285
www.WarmlyYours.com
Prodeso Accessories
Prodeso ProBand rolls and Prodeso Preformed Corners, is a
waterproof polyethylene tape with a non-woven fleece sheet
on both sides, which ensures adhesion. Used in construction of
perimeter joints and between adjacent sheets of Prodeso Heat
Membrane. Guarantees waterproofing of indoor environments
that may come in contact with water such as bathrooms, saunas
and kitchens.
Available Sizes
Prodeso
Membr ne
a
SKU Dimensions
TC-MEM-BL-BND-0616
TC-MEM-BL-BND-0698
TC-MEM-BL-CNR-IN
TC-MEM-BL-CNR-OUT
Prodeso ProdBand 6” x 16’
for Membrane (Roll)
Prodeso ProdBand 6” x 98’
for Membrane (Roll)
Prodeso Preformed
Inside Corner 6” x 6”
for Membrane (Each)
Prodeso Preformed
Outside Corner 6” x 6”
for Membrane (Each)
MSRP USMSRP
$29.00 $39.00
$129.00 $169.00
$9.00 $12.00
$9.00 $12.00
Prodeso Proband Rolls
CA
Prodeso Preformed
external corner
Prodeso Preformed
internal corner
Loading...