Page 1
Hardwired Model Shown
WarmlyYours Infinity Towel Warmer
Installation & Operation Manual
Page 2
Thank you for choosing a nely crafted WarmlyYours Innity towel warmer.
The Innity’s radiant heat gently warms your towel or bathrobe, allowing you
to wrap yourself in luxurious comfort as you step out of the bath or shower.
Included in this document are all necessary installation and operating
instructions.
To locate the model number, refer to the product label as shown in Diagram
D on page 8. If you encounter any diculties while installing your towel
warmer, installation support is available by phone between 8:00 a.m. and
5:30 p.m. CT, Monday through Friday by calling (800) 875-5285. If a return
is necessary, please use original packaging.
SAFETY INFORMATION
• Never stand, sit on, or hang on the towel warmer unit.
• Never allow children to play on or with the towel warmer.
• Make sure that the electrical circuit breaker is shut o at the main panel before
wiring or servicing your towel warmer.
• The towel warmer must be properly grounded.
• All wiring must be in accordance with the National Electrical Code (NEC)
and Canadian Electrical Code (CEC) and should be performed by a licensed
professional who is certied to do electrical wiring.
• Never place your towel warmer inside a shower, sauna, or steam room.
• Never attempt to warm more than two (2) towels on the towel warmer at a time.
Overloading the towel warmer will cause the unit to become extremely hot and
may result in a burn if touched. (See page 10 for additional information.)
• Innity towel warmers are cULus listed for use in US and Canadian markets.
• Never use an extension cord (for plug-in model).
CLEANING INFORMATION
Clean the towel warmer with a soft, non-abrasive, damp cloth while warm.
Once the towel warmer has cooled, lightly polish with a soft, dry cloth.
Do not use abrasive cleaning powders, metal polish, or chlorine based
cleaners on any part of the towel warmer.
INSTALLATION
This appliance must be installed in accordance with the instructions in the
manual and the NEC and CEC guidelines relating to electrical xtures in
bathrooms. The towel warmer must be on a GFCI-protected circuit and be
wired by a professional who is certied to do electrical wiring. If the towel
warmer does not heat upon initial installation, PLEASE VERIFY THAT THE
POWER SWITCH, LOCATED AT THE BOTTOM OF THE LEFT, VERTICAL
POST, IS IN THE ON POSITION.
1
Page 3
1. Afxing the Towel Warmer to the Wall
Step 1
Draw a diagram of the preferred location of the brackets and the electrical
connection on the towel warmer box to create a template (see Step 2 for
template instructions). At least two of the four brackets must be attached
directly to a stud.
The Innity Plug-In model must be installed less than 6 feet (183cm) from
a properly grounded outlet to ensure the plug can reach. Make sure to
measure the distance from where to plug is attached to the towel warmer to
the electrical outlet. Do NOT use an extension cord to make the connection
between the towel warmer plug and outlet.
Step 2
A. Attach tubing into desired positions on the towel warmer (see pages 5-8
for bracket assembly).
B. Place towel warmer on the box (or a large sheet of paper) and lay on a
at surface with brackets facing downwards.
C. Mark the location of the following:
• The electrical collar (hardwired model only)
• The location of the brackets
D. Use the template as a guide to mark the wall with the correct locations
of the four brackets, ensuring the following:
• The electrical collar is lined up with the center of the electrical
box (hardwired model only). Plug-in model must be installed less
than 6 feet (183cm) from properly grounded outlet. Do NOT use
an extension cord.
• At least two of the brackets are lined up with a wall stud.
• The towel warmer is level.
Step 3
Install the brackets onto the wall. Use the drywall anchors that are
supplied for the brackets that are not being installed into a stud. Refer to
Diagrams A and B.
2
Page 4
1. Afxing the Towel Warmer to the Wall (continued)
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16 inches on center construction. Your
situation may vary depending on stud spacing.
WARNING: Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
Diagram A: Anchor Points and Electric Box Location
stud stud
16” (406mm)
3/8
22
” (568mm)
1/8
8
”
(206mm)
anchor point
15
1/4
anchor point*
”
(388mm)
anchor point*
†
Note: For hardwired model only, electrical box must be securely attached to a
stud. Plug-in model only must be installed less than 6 feet (183cm) from
properly grounded outlet. Do NOT use an extension cord.
* Note: Anchor points must be attached to a stud.
anchor point
7/8
” (201mm)
7
electrical collar
electrical box
3
†
Page 5
1. Afxing the Towel Warmer to the Wall (continued)
Diagram B: Rough-In Diagram
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16 inches on center construction. Your
situation may vary depending on stud spacing.
WARNING: Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
2” X 4” STUD
(51mm x 102mm)
15 1/4”
(388mm)
MOUNT CENTER OFJUNCTION BOX
22 3/8” (568mm) TO THE RIGHT OF CENTER OF STUD
2” X 4” STUD
(51mm x 102mm)
16” (406mm)
22 3/8”
(568mm)
8 1/8”
(206mm)
PERMANENT 120V ac
FROM HOUSE POWER
Hardwired Model Only
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX
FOR OPTIONAL CONTROL
1/2” (13mm) CONDUIT
Hardwired Model Only
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX FOR TOWEL
WARMER CONNECTION
†
†
Note: For hardwired model only, electrical box must be securely attached to a
stud. Plug-in model only must be installed less than 6 feet (183cm) from
properly grounded outlet. Do NOT use an extension cord.
* Note: Anchor points must be attached to a stud.
4
Page 6
2. Bracket Assembly Instructions
B
C
C
A
B
C
d e f g h
A
B
C
g
h
A
B
C
d e f g h
C
Diagram C: Bracket Assembly Diagrams - In nity
A
B
d e f g h
C
5
Page 7
2. Bracket Assembly Instructions (continued)
B
C
C
C
C
B
C
C
Innity TW-F10BS-HW Parts List
A
B
C
d e f g h i j
Innity Brushed Nickel TW-F10BS-HW
PART # QTY DESCRIPTION
A. 0005-57110-0001 4 Bracket, mounting, stainless steel
B. 0005-57110-0002 4 Tube assy., mounting, stainless steel
C. 0005-57300-0001 4 Screw, tube mounting, 8mm x 70mm
d. 0005-57900-0001 1 Wrench, hex key, 8mm
e. 0005-57900-0002 1 Wrench, hex key, 6mm
f. 0005-57500-0001 4 Anchor, drywall, #8, white
g. 0005-57200-0001 4 Screw, #8, 50x4.2mm, at
h. 0005-57200-0002 4 Screw, set, 6mm, hex
i. 0005-57810-0000 1 Collar
i. 0005-57820-0000 1 Wall plate
AK05-57820-0001 N/A Parts Kit Assy., Innity, TW-F10BS-HW
6
Page 8
2. Bracket Assembly Instructions (continued)
Step 1
Measure for bracket positions using the template if desired. At least two brackets
must be attached to a stud.
Step 2
Ax brackets A to the wall using screw g and drywall anchor f where necessary.
Repeat Step 2 for the three remaining brackets.
Step 3
Place and orient the curved end of tubing B with the threaded inserts located at
four points on the back of the towel warmer. Ax tubing B to the threaded inserts
with bolt C and tighten using the large Allen wrench d provided.
Repeat Step 3 for the three remaining sections of tubing.
Step 4
Loosen the hex-head screws h at the base of each section of tubing B using the
smaller Allen wrench e provided. Hang towel warmer by aligning and sliding all
four sections of tubing B over bracket A. Partially tighten hex-head screws h at
the base of each section of tubing B to hold the towel warmer in place but do
NOT fully secure the fasteners at this time.
Step 5
Please remove the protective lm from the cover plate.
Plug-In Model Skip Steps 6-8.
Hardwired Model Only
Slide the brushed stainless collar over the end of the stainless steel tubing where
the wires come out of the unit. Make sure to slide the collar over the tubing
so that the larger diameter opening is facing away from the towel warmer and
toward the electrical cover plate that will be placed on the towel warmer next.
Remove the plastic coating from the cover plate. Slide the cover plate over the
same section of stainless steel tubing. Refer to Diagram E. Do not remove
rubber O-ring from electrical plate under any circumstances. Make sure the
cover plate is slid on the tubing so that the back of the cover faces away from the
towel warmer and toward the electrical outlet.
Step 6
Have a certied professional wire the towel warmer to the electrical circuit according
to code, referring to the detailed wiring diagram provided in Diagram F.
Step 7
Push the wires into the electrical box and screw the cover plate to the outside of
the box with the screws provided.
7
Page 9
2. Bracket Assembly Instructions (continued)
on
off
economy
TOWEL WARMER
Step 8
Hardwired Model Only (continued)
Ensure the rubber seal is in position and sealed correctly inside the collar.
Refer to Diagram E. Slide the brushed stainless collar over the tube until
it is touching the face of the O-ring on the cover plate.
Hardwired Model Skip Steps 9-10.
Plug-In Model Only
Plug the cord into a properly grounded outlet. Do NOT use an extension
cord to make the connection between the towel warmer plug and outlet.
Step 9
Hold the towel warmer in place while tightening the hex-head screws h
at the base of each section of tubing B using the smaller Allen wrench e
provided to secure the towel warmer in place.
Step 10
Make sure the unit is turned on using the ON/OFF switch located at the
bottom rail on the left side (when facing the towel warmer). A red light will
illuminate the switch when the switch is turned to the “ON” position. Refer
to Diagram D for switch location.
Diagram D
Switch
Towel Warmer
Collar
8
Diagram E
(hardwired model only)
O-Ring
Cover Plate
Page 10
3. Electrical Considerations
Diagram F: Wiring Diagram (hardwired models only)
120V OPTIONAL CONTROL
On
TOWEL WARMER
3-WAY WIRE
(YELLOW)
LINE
(black)
NEUTRAL
(white)
LOAD
(blue)
BLACK or BLUE
(Hot)
WHITE or BROWN
(Neutral)
2” x 4” ELECTRICAL
BOX FOR
OPTIONAL CONTROL
120V ac HO T
NEUTRAL
GROUND
GREEN/YELLOW
(Ground)
HOT LOAD
(black or blue)
NEUTRAL LOAD
(white or brown)
9
GROUND
(green/yellow)
2” x 4” ELECTRICAL BOX
Page 11
4. OPERATION
Manual
Use the ON/OFF switch located on the bottom left side (when facing the towel
warmer) to control when you want the unit to warm. Refer to Diagram D for
switch for location.
With a Control
You may want to pair your towel warmer with a compatible WarmlyYours timer
or switch. Make sure to refer to the installation manual of the control for proper
operation and installation. If you have any questions, call 800-875-5285.
Warning
For optimum operation of your new towel warmer, we recommend placing
no more than two (2) towels at a time on the warmer. Place the towels in a
way to maximize the contact area between the towel and the towel warmer.
The towel will be its warmest when it is placed over the top bar. This allows a
greater portion of the towel to make the most contact with the warmer.
10
Page 12
5. SPECIFICATIONS
Item # Model Dimensions Volts Watts Ohms Amps
TW-F10BS-HW Hardwired
W: 3 5/8” (600mm)
H : 32” (811mm)
D: 4 ¾” (121mm)
120 150 95 1.25
TW-F10BS-PL Plug-In
W: 23 5/8” (600mm)
H: 32” (811mm)
D: 4 ¾” (121mm)
120 150 95 1.25
Product Construction - Innity Towel Warmer
The Innity Towel Warmers are constructed from Type 304 stainless steel
and have a brushed nish. The stainless steel tubing is pre-assembled
and tack-welded together for rigidity. The towel warmer is heated by a
cULus Listed wire. The tubing used to hang the towel warmer is also
made of Type 304 stainless steel with a brushed nish. The plug-in model
is equipped with a UL Listed plug with grounding pin attached to a 6-foot
(1.8m) cord.
Connection Method
The plug-in model has a 6-foot cord, which is located on the right side
of the unit. Keep cord location and length in mind and plan accordingly
when determining placement of the towel warmer in the room. The unit
must be plugged into an outlet that is properly grounded. For automatic
control of the plug-in unit, a timer can be used. The Innity hardwired
model is fed electricity into the towel warmer via a section of stainless
steel tubing. The tubing can rotate to facilitate wiring. The tubing has an
outside diameter suitable to secure the rubber O-ring on the electrical
cover plate. The stainless steel tubing projects through the O-ring and
into the front of the 2” x 4” (51mm x 102mm) electrical junction box that
is properly grounded. This box is secured in the wall and, a water resistant
seal is made with the use of the rubber O-ring. Power can then be fed to
the control unit, which may be located anywhere in the room.
Safety Ratings
Innity Towel Warmers are cULus Listed and are suitable for use in US
and Canadian markets. The main electrical line feeding the towel warmer
must incorporate an Appliance Leakage Current Interrupter (ALCI) for
North America.
11
Page 13
6. WarmlyYours Towel Warmer Warranty
WarmlyYours.com Inc. warrants the WarmlyYours towel warmers (“the Product”) to
be free from defects in materials and workmanship for two years from the date of
sale, provided that the Product is installed in accordance with the accompanying
Installation and Operation Manual and any special written design or installation
guidelines provided by WarmlyYours.com Inc. for this product, the National
Electric Code (NEC) and Canadian Electrical Code (CEC), and all applicable local
building and electrical codes. Controls sold under the WarmlyYours.com Inc.
name are warranted for one year from the date of sale.
Any suspected defect must be reported by registered letter immediately upon
discovery. The determination of such a defect must be made by WarmlyYours.
com Inc. or its authorized representative only. This warranty is null and void if the
product is improperly installed, improperly operated, or abused. WarmlyYours.
com Inc. assumes no responsibility under this warranty for any damage to the
product caused by any trades person, or visitor on the job site, or damage caused
as a result of post installation work.
Under this Limited Warranty, WarmlyYours.com Inc. will provide the following
remedy:
If the Product is determined to be defective in materials and workmanship, and
has not been damaged as a result of misuse or misapplication, WarmlyYours.
com Inc. will refund the original purchase price or replace the towel warmer, at
WarmlyYours.com Inc. expense. WarmlyYours.com Inc. will not be liable for the
labor required to replace the towel warmer.
The Limited Warranty is null and void if the project owner or his representative
attempts to repair the Product without receiving authorization. Upon notication
of a real or possible problem, WarmlyYours.com Inc., will issue an Authorization
to Proceed under the terms of the Limited Warranty.
WARMLYYOURS.COM INC. DISCLAIMS ANY WARRANTY NOT PROVIDED
HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WARMLYYOURS.COM INC. FURTHER DISCLAIMS ANY RESPONSIBILITY
FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,
INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR
REPRESENTATIVE OF WARMLYYOURS.COM INC. HAS ANY AUTHORITY
TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR
MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
Please ll in warranty card information at
http://www.warmlyyours.com/towel-warmers/warranty
or call (800) 875-5285 to register via phone.
5/2018
12
Loading...