WarmlyYours TWE4PCP Installation Manual

Installation & Operation Manual for

WarmlyYours Towel Warmers

Thank you for choosing a fi nely crafted Towel Warmer from the Elements™
Collection by WarmlyYours. Now you can enjoy the luxury of a warm towel
everyday. These models are so easy to install and use. Just plug the Towel
Warmer unit into a standard 120V outlet, pre-heat your towel warmer and
enjoy a warm, dry towel or bathrobe upon stepping from the shower.

All of the necessary installation and operation instructions are included in this
manual. Please read the instructions carefully before installing and operating
your towel warmer. If you encounter any diffi culties while installing your unit,
installation support is available by telephone between the hours of 8:00am­5:30pm CST, Monday through Friday by calling [phone]. Please
reference the model number on the Towel Warmer label when you call. For
label location, see page 11, Diagram A.

SAFETY INFORMATION

• Towel Warmers are designed to warm towels and bathrobes only and should
not be used for any other purpose.

• Never stand, sit, or hang on the Towel Warmer unit.

• Never allow children to play on or with the Towel Warmer. Close supervision
is necessary when using any electrical appliance by or near children.

• Unplug unit and ensure that the electrical circuit breaker is shut off at the
main panel before wiring, repairing, or servicing your Towel Warmer.

• All wiring must be in accordance with the National Electrical Code and
should be performed by a licensed professional who is certifi ed to do
electrical wiring.

• Never place your Towel Warmer inside a shower, sauna or steam room or
immerse in water for any reason.

• Never attempt to warm more than 2 towels on the Towel Warmer at any time.
Overloading the Towel Warmer will cause the unit to become extremely hot
and may result in a burn if touched.

• To provide continued protection against risk of electric shock, plug the unit
into properly grounded outlets only.

• Approved for Household use only; Do not use outdoors.

• Unplug from outlet when not in use.

• Never operate any electrical appliance with a damaged cord or plug.

CLEANING INFORMATION

Unplug the Towel Warmer before cleaning. Clean the Towel Warmer with
a soft, non-abrasive, damp cloth while warm. Once the Towel Warmer has
cooled, lightly polish with a soft dry cloth. Never use abrasive cleaning
powders, metal polish, chlorine or acid based cleaners on any part of the
Towel Warmer.

1

INSTALLATION

This appliance must be installed in accordance with the instructions in the
manual and the NEC guidelines relating to electrical fi xtures in bathrooms.
We recommend that the Towel Warmer be plugged into a GFCI protected
circuit.

Install the Towel Warmer as close to an electrical outlet as possible. If an
extension cord becomes necessary, always use a grounded 3-wire extension
cord. Confi rm that the cord’s electrical rating is at least as high as the electrical
rating of the Towel Warmer. Ensure that the extension cord is a suffi cient length
to reach the outlet so as not to put undue strain on the cord. Use caution
when arranging the cord to prevent tripping, snagging, or unintentional pulling
(especially by children).

Tools Required

• Drill, Cordless or otherwise - Use to make holes in dry
wall and studs as required

• Phillips # 2 Screwdriver or Phillips # 2 Drill Bit -
Use to tighten the mount with screws into the
drywall anchors

• Hammer - Use to sink the anchors into the drywall

• Hex Key Set, US - Use to tighten the mounting hardware
bolts onto the pivot model of Towel Warmer (TW-E4PCP)

• Level - Use to make sure that the Towel
Warmer is mounted level

• Yard Stick or Tape measure - Use to measure the distance
between Towel Warmer mounting brackets to ensure that
they mount in line

Note: Use other mounting hardware suitable for wall substrate when

required.

2

Affi xing the Towel Warmer to the Wall

NOTE: Install the Towel Warmer no less than 1 foot from the fl oor and
near an electrical outlet. The electrical outlet must be properly grounded.
Position the brackets on the Towel Warmer to ensure that the Towel
Warmer is fi rmly affi xed to the wall. See pages 8,9 and 10 for for bracket
assembly and installation recommendations.

Step 1

Draw a diagram of the recommended location of the brackets on
the Towel Warmer box to create a template (see Step 2 for template
instructions). Two brackets must be mounted directly to a stud (see
pages 5, 6 and 7 for anchor points).

Step 2

Create the Template:

• Attach brackets into recommended position on the Towel Warmer
(see pages 8, 9 and 10 for recommended bracket assembly for each
model).

• Place Towel Warmer on the box (or a large sheet of paper) and lay on
a fl at surface with brackets facing downwards.

• Mark the location of the brackets on the template.

Step 3

Use the template as a guide to mark the wall with the correct locations
of the brackets. Make sure two of the brackets are lined up with a wall
stud. Ensure that all anchor points are clear of existing electrical or
mechanical systems.

Step 4

Using the template, check to make sure that the Towel Warmer will be
level once installed.

Step 5

Drill holes as required at the marked locations and install the brackets
into the wall using the hardware that has been provided. Use the drywall
anchors that are supplied for any bracket which is not being installed
into a stud.

3

Step 6

With the brackets now in place, adjust the Towel Warmer to desired
position and fully tighten the screws into place.

Step 7

Plug the Towel Warmer into a GFCI 120V, 15A electrical outlet. Enjoy!

4