WarmlyYours Mirror Defogger User Manual

Instructions & Operation Manual

for WarmlyYours Mirror Defoggers

Congratulations on the purchase of your Mirror Defogger. This
system can be easily installed behind any mirror to keep it steam
free and crystal clear whenever you use the bathroom. Simply turn
on the lights and the Mirror Defogger will provide a clear, steam
free section of mirror for you to begin your day.

SAFETY INFORMATION

• All wiring must be in accordance with the National Electrical
Code (NEC) and should be performed by a licensed professional
who is certied to do electrical wiring.

• Make sure that the electrical circuit breaker is shut off at the main

panel before wiring your Mirror Defogger.

• Never place your 120 volt Mirror Defogger inside a shower, sauna,

or steam room.

• Check the Mirror Defogger for damage before installation.

Creases, tears or other obvious damage may cause the unit to
malfunction.

• Do not overlap Mirror Defoggers when using more than one on

a mirror.

• Never cut or resize the Mirror Defogger.

• Use caution with all electrical appliances.

• Install in compliance with these instructions.

CLEANING INFORMATION

Use ordinary window cleaner to clean mirrors which have the

Mirror Defogger installed, just as you would any other mirror.

1

INSTALLATION INSTRUCTIONS

Circle
Circle
Circle

Circle
Circle
Circle

This appliance must be installed in accordance with the instructions

in this manual and the NEC guidelines relating to bathroom electrical
xtures. The Mirror Defogger must be on a GFCI protected circuit
and wired by a professional certied to do electrical wiring.

Determine Location of Mirror Defogger

Step 1

Choose a location for your Mirror Defogger so that everyone in
your home can enjoy it.

• For the larger rectangular and oval shaped Mirror Defoggers,
place the system so that the top edge is 6’6” above the oor.

Refer to Diagram A.

• For smaller rectangular and circular shaped Mirror Defoggers,

center them over the vanity and in the center of the mirror.
Refer to Diagram B.

Step 2

Mark the wall with the location where you will be installing the
Mirror Defogger. Mark the location where the lead wires leave the
Mirror Defogger.

Diagram A

Diagram B

2

INSTALLATION INSTRUCTIONS

Step 2 - Cont.

Location where the lead wire leaves the Mirror Defoggers.

6”

12”

12”

25.75

”

FFM-2432OV

6”

9” 11”

9” 11”

5.75”

20

9”

”

9”

FFM-1826OV

5”

”

18

FFM-1824

”

26

FFM-2432

3

INSTALLATION INSTRUCTIONS

Step 2 - Cont.

Location where the lead wire leaves the Mirror Defoggers.

12.5”

7.5”

19.5

5.5”

FFM-25R

5.5”

9.25

”

12.5”

7.5”

”

10”

FFM-20R

6”

14.75”

”

6

5.75”

6”

”

12

10”

FFM-15R

FFM-1218

4

Prepare Electrical Rough-In and Wiring

leads from Mirror Defogger

to light junction box

Step 3

Using the location you determined in Step 2, install a 2” x 3”
remodeler’s electrical junction box inline with the Mirror Defogger’s

lead wires. Refer to Diagram C.

Note: The location where the wires leave must be entirely within the

area of the new electrical junction box.

Step 4

Run Romex cable from a nearby junction box to the new box.
Typically the most convenient junction box is the one that supplies

power to the lighting above the mirror. This will enable the system
to turn on automatically whenever the bathroom lights are turned
on.

Wall

ClearlyYou™ Defogger

Mirror

Existing
electrical box
for vanity
lighting

New single
gang electrical
box

Diagram C

5

Attach Mirror Defogger to the back of the Mirror

Wall

Existing
electrical box
for vanity
lighting

New single
gang electrical
box

to light junction box

Circle
Circle
Circle

Step 5

Place the element on the mirror so that it will line up with the
markings on the wall.

Step 6

Dry t the Mirror Defogger on the mirror, and line up the lead wires
with electrical box. Do not remove paper backing yet. Draw an

outline of the Mirror Defogger on the mirror.

Step 7

Peel back 2” of backing from the Mirror Defogger and line it up with
outline drawn in Step 6. Adhere backing to the top of the Mirror

Defogger and slowly remove the rest of the backing, sticking the
Mirror Defogger to the back of the mirror as you progress, to smooth
out any air bubbles that may appear. Refer to Diagram D.

Note: If gluing mirror to wall, apply adhesive to the mirror backing,

not covered with the Mirror Defogger.

Mirror Defogger

Back of Mirror

Power Cord

Remove Protective
Paper

Diagram D

Electrical Wiring

Step 8

With the assistance of another person, position the mirror so the

leads can be connected to the Romex cable as referred to in Step

4. Refer to Diagram E for specic wiring instructions.

6

Electrical Wiring Step 8 - continued

Diagram E

to light junction box

leads from Mirror Defogger

Step 9

Push the excess wire into the junction box.

Step 10

Wire the Romex cable to the junction box that houses the electrical
wiring for the existing lighting.

Install Mirror

Step 11

Install mirror in line with the mirror manufacturer’s instructions.

OPERATION

By wiring the Mirror Defogger to the lighting above the vanity, the
Mirror Defogger will automatically turn on whenever you turn on
your vanity lighting. The Mirror Defogger will begin to defog within
5 minutes of operation.

SPECIFICATIONS

7

Safety Ratings

The Mirror Defogger is UL listed under standard 499. The main

electrical line feeding the Mirror Defogger must incorporate a

GFCI for North America. For the le number, please contact

WarmlyYours.

8

WarmlyYours Warranty Information

WarmlyYours.com Inc. warrants the WarmlyYours Mirror Defogger (“the Product”)
to be free from defects in materials and workmanship for 1 year from the date of

sale, provided that the Product is installed in accordance with the accompanying

Instructions and Operation Manual, any special written design or installation
guidelines provided by WarmlyYours.com Inc., the National Electrical Code (NEC),

and all applicable local building and electrical codes.

Any suspected defect must be reported by registered letter immediately upon
discovery. The determination of the existence of such a defect will be made by
WarmlyYours.com Inc., or its authorized representative only. Upon notication of
an actual or possible problem, WarmlyYours.com Inc. will issue an Authorization

to Proceed under the terms of the Limited Warranty.

This warranty is null and void if the Product is improperly used, operated or
installed, or if the owner or his representative attempts to repair the Product

without receiving authorization.

Under this Limited Warranty, WarmlyYours.com Inc. will provide the following
remedy:

If the product is determined to be defective in materials and workmanship, and has

not been damaged as a result of misuse, misapplication or improper installation,

WarmlyYours.com Inc. will refund the original purchase price or replace the

Product.

WARMLYYOURS.COM INC. DISCLAIMS ANY WARRANTY NOT PROVIDED
HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WARMLYYOURS.COM INC. FURTHER DISCLAIMS ANY RESPONSIBILITY
FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,
INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE FACE OF THE DOCUMENT. NO AGENT OR
REPRESENTATIVE OF WARMLYYOURS.COM INC. HAS ANY AUTHORITY
TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR
MODIFICATION IS IN WRITING BY A CORPORATE OFFICER.

Please ll in warranty card information at www.warmlyyours.com/warranty/md or
to register via phone, please call [phone] to speak to one of our customer

service representatives.

10128-A

09/2011

9