MANUAL
OPERATION
MICROPHONE
WA12 DISCRETE
PREAMPLIFIER
your unit until you find the settings you like.
using your WA12. Because of the endless combinations of DAWs and
The information contained in this manual is written to help you get quickly started
Microphones, we encourage you to read through this manual then experiment with
YOUR PURCHASE DATE TO SECURE YOUR 1 YEAR WARRANTY.
Don't forget to log on to www.warmaudio.com to register your unit!
PLEASE COMPLETE YOUR ONLINE REGISTRATION WITHIN 14 DAYS OF
All Content Copyright 2012 Warm Audio - All Rights Reserved
Warm Audio - Round Rock, Texas USA WarmAudio.com
Engaging this feature applies -20db to the incoming signal.
The front panel ¼” input sends the instrument's signal through the
This feature engages the front panel ¼” input and turns off the back
The 48 volts feature provides power for condenser mics and any
This feature inverts the polarity of the signal. Use the phase invert
When engaged the input impedance of the preamp is 150 ohms.
The gain control is variable and adjusts the WA12's gain from +29db
The power button is used to power the unit on and off. To extend
4. HI-Z Input:
entire preamp circuit including the input transformer, discrete opamp (operational
amplifier) and output transformer. The thorough layout of the HI-Z's signal path
ensures that instruments are subject to the same robust pre-amplification as the
microphones. You can connect a variety of instruments via the Hi-Z input on the front
panel of the WA12 including: acoustic and electric guitars, bass guitar as well as older
The WA12 has +48V phantom power available. This
5. HI-Z Switch:
keyboards with Hi-Z instrument level output.
6. +48V Switch:
panel XLR/TRS combo input.
This feature enables you to “tune”
other devices requiring continuous phantom power through the XLR input. This power
is supplied at a constant level to prevent any degradation of audio quality.
Different outputs are provided on the WA12 to be
7. -20dB PAD Switch:
This is a very useful feature for reducing the level coming into the WA12 and thus
preventing the signal from clipping or distorting. This may occur due to high output
level from a microphone or other device. Padding the input serves to provide
increased “headroom” for the operator while lessening the likelihood of signal
8. POL Switch:
overload.
when recording with more than one open microphone to combat phase cancellation
between microphones.
9. TONE Switch:
When dis-engaged the input impedance of the preamp is 600 ohms. The 150 ohm
(switched-in) setting increases the gain of the preamp by +6db changing the
maximum gain from +65db to +71db. This feature will make a noticeable tone change
to most microphones and instruments. The back panel XLR input and front panel HI-
Z input are both altered by this feature.
The 600 ohms impedance setting is recommended for condenser and dynamic
microphones, and 150 ohms is recommended for ribbons. This button is labeled
"TONE" for a reason though, we strongly suggest you experiment with both settings
2 outputs are provided, balanced XLR and TRS. These
10. GAIN Knob:
on all sources to find the best possible tone for your mixes.
Different inputs
to +65db or from +35db to +71db when the “TONE” switch is engaged. The “PAD”
11. Power Button:
feature lowers the minimum and maximum ranges by -20db when engaged.
the life of the electronics please turn unit off when not in use.
OPERATION
The WA12 works great with all types of microphones including dynamic, ribbon and
condenser microphones. Dynamic microphones and ribbon microphones are
generally lower output devices and require no external power source. Condenser
microphones are generally more sensitive than dynamic and ribbon microphones and
typically require external +48V phantom power.
FEATURES
The following information is a summary of your WA12's features:
Your WA12 is a completely discrete, high voltage, dual-transformer microphone pre-
amplifier designed for high gain (+71dB), high headroom, low noise and an exciting
+48 Volt Phantom Power.
sonic performance – great for all types of recording applications.
assures optimum performance of your condenser microphones that require phantom
Variable Input Impedance (600 or 150 ohms).
power.
your microphones and instruments – experiment with 2 different input impedances to
create different sounds from your microphones and instruments. Changing the input
Balanced XLR and TRS outputs.
impedance can be the perfect solution for a given recording application.
used simultaneously or separately to accommodate the many applications the WA12
is suited for.
D E S C R I P T I O N
The following is a description of the features on your WA12:
The WA12 is designed to use a 24V AC power supply. Warm Audio
1. XLR & TRS outputs.
outputs can be used simultaneously. When using 2 WA12's in stereo as a mastering
bus one set of outputs can be assigned to the monitor speakers while the other set
2. Microphone level input (XLR & TRS) / Hi-Z Instrument Input.
returns the conditioned signal back to the DAW to be recorded.
are provided on the WA12 for maximum flexibility. You can connect microphones,
instruments, keyboards as well as run your entire mix through 2 WA12's during mix-
3. AC POWER:
down or mastering to condition your signal with exceptionally smooth warm character.
recommends that you use the 24V AC supplied in the original box or another of
identical spec.
Loading...