For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
An que cet appareil vous procure en toute sécurité beaucoup de satisfaction,
lire attentivement le mode d’emploi avant de l’utiliser.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed, including the following:
1.
READ ALL INSTRUCTIONS.
2. To protect against risk of electrical shock, do not put
appliance in water or other liquid.
3. Do not use carbonated liquids in the blender jar, or any
blending container. Using carbonated liquids in the
blender jar or any blending container may result in injury.
4. Unplug from outlet when not in use, before putting on or
taking off parts, and before cleaning.
5. Avoid coming into contact with moving parts.
6. Do not operate the Waring Pro
equipment with a damaged cord or plug, or after the unit
malfunctions, or is dropped or damaged in any manner. Return
it to the nearest authorized service facility for examination,
repair, or adjustment.
7. The use of attachments, including canning jars, not
recommended or sold by Waring Pro
shock, or injury.
8. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
9. Keep hands and utensils out of jar while blending, to prevent
the possibility of severe personal injury and/or damage to the
blender. A rubber spatula may be used, but must be used only
when the blender is not running.
10. Blades are sharp. Handle carefully.
11. To avoid injury, never place blade assembly on the base unless
container is properly attached.
12. Always operate blender with cover in place.
13. For blending hot liquids, see Hot Blending Instructions, page 4.
14. Screw on base collar rmly when assembling container. Injury
can result if moving blades accidentally become exposed.
15. Do not leave blender unattended while it is running.
16. Do not operate your appliance in an appliance garage or under
a wall cabinet.When storing in an appliance garage, always
®
Blender or any other electrical
®
may cause re, electric
unplug the unit from the electrical outlet. Not doing so
could create a risk of re, especially if the appliance touches
the walls of the garage or the door touches the unit as it
closes.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
CONTENTS
Important Safeguards .................................................................. 2
The Tailgater™ Blender includes an AC converter for home use.
For your protection, the AC converter has a 3-conductor cordset
with a molded 3-prong grounding-type plug, for use with a properly
connected grounding-type outlet as shown in Figure 1.
If a grounding-type outlet is not available, an adapter, as shown in
Figure 2, may be obtained so that a 2-slot wall outlet can be used
with a 3-prong plug. As shown in Figure 3, the adapter must be
grounded by attaching its grounding lug under the screw of the
outlet cover plate. CAUTION: Before using an adapter, it must be
determined that the outlet cover plate screw is properly grounded. If
in doubt, consult a licensed electrician. Never use an adapter unless
you are sure it is properly grounded.
OPERATING INSTRUCTIONS
1. When placing the container on the unit base, make sure that
the unit is turned to OFF and is at a complete stop. Do not put
the container on or take it off while the unit is running. Doing
so may damage the drive shaft or blade assembly. For best
results, do not ll container above 3-cup level.
2. With the switch in the OFF position, plug the blender into
a 12 Volt car outlet.
3. The Waring Pro
drinks. For best results, keep the blades covered with liquid,
turn the unit to ON, remove the lid insert, and feed the ice
cubes slowly into the container. NOTE: Never use containers
other than Waring Pro
Waring unit.
4. CAUTION: DO NOT use carbonated liquids in the blender
jar or any blending container.Using carbonated liquids in the
blender jar or any blending container may result in injury.
5. For other blending tasks, put ingredients into container, then
put the lid on rmly. Always add liquid ingredients rst, unless
otherwise specied in recipe. Always hold container with one
hand while blending.
®
Tailgater™ Blender is ideal for blending ice
®
Blender containers with your
Note: Use of an adapter is not permitted in Canada.
IMPORTANT: HOT BLENDING INSTRUCTIONS
To minimize possibility of being scalded when blending hot
ingredients, the following precautions and procedures must be
observed:
1. Begin blending with no more than one cup (8 oz.) of
ingredients.
2. Before turning blender on, remove the center lid insert. This will
allow venting of the rapidly heated and expanding air.
3. Start blending on low speed.
4. While blender is running, up to 1½ cups (12 oz.) of additional
liquid can be added. Pour liquid slowly through the opening in
the lid.
4
5
HOW TO ASSEMBLE CONTAINERS WITH
REMOVABLE BLADES
Always wash and rinse container prior to initial use.
1. Before starting, make sure that the
blender cord is unplugged and that the
switch is in the OFF position.
2. Refer to Figure 1. The following points
are important to note when putting
together the container assembly:
•Containergasketmustbeplaced
between blade assembly and
container.
•Collarmustbethreadedproperly
onto the blender container base, and
securely tightened before placing food
or liquid in the container.
•Toensureproperassembly,placethe
blender container upside down and
turn the collar counterclockwise until securely tightened.
3. Place assembled blender jar on unit base so that it is rmly
seated and not tilted to one side. Never place the collar or
blade assembly on the unit base unless the container has been
completely assembled and securely tightened.
HOW TO CLEAN UNIT BASE
To clean the unit base, unplug the power cord. Wipe the exterior
surfaces with a soft cloth or sponge dampened with cleaning
solution. Rinse with clean water. Do not immerse the base in
cleaning solution or water. Wipe the base with dry towel.
FUSE REPLACEMENT
The plug on the blender power cord contains a replaceable
cartridge fuse. To gain access to the fuse, push the metal tip of the
plug inward as far as it will go, then turn it counterclockwise until
it releases. Withdraw the tip, with the fuse attached, by pulling it
straight out of the plug body. Replace fuse with one of same size
and rating (15 Amperes, 32 Volts, Slow-Blow). Reassemble plug
by reversing above procedure.
Any other servicing should be performed by an authorized service
representative.
HOW TO DISASSEMBLE & CLEAN CONTAINERS
WITH REMOVABLE BLADES
Always wash and rinse container immediately after use.
1. Be sure the switch is in the OFF position.
2. Remove the container assembly from the unit base and empty
the contents.
3. To disassemble the Waring Pro
container collar clockwise.
4. The collar, blade assembly and gasket are dishwasher safe.
The plastic container lid and insert must be washed by hand.
Allow all parts to air dry.
5. Be certain all components are in the proper position when
reassembling blender container and base.
®
Tailgater™ Blender, turn
6
7
Loading...
+ 7 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.