For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
An que votre appareil vous procure en toute sécurité beaucoup
de satisfaction, lire attentivement les directives avant de l’utiliser.
TBB16 0
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be taken, including the following:
1.
READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in use, before putting
on or taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse the
blender base in water or other liquids.
4. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
5. Children should be supervised to ensure that they
do not play with the appliance.
6. Avoid contact with moving parts.
7. Do not operate any appliance with a damaged cord or
plug or after the appliance malfunctions or is dropped or
damaged in any manner. Return appliance to the
nearest authorized service facility for examination, repair or
electrical or mechanical adjustment.
8. The use of attachments not recommended by the appliance
manufacturer may cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, where it
can inadvertently be pulled on or tripped over or touch hot
surfaces, which could damage the cord.
11. Keep hands and utensils out of container while blending
to prevent the possibility of severe personal injury and/or
damage to the blender. A rubber scraper may be used, but
must be used only when the blender is not running.
12. Blades are sharp. Handle carefully.
13. Never place cutting assembly or cutting blades on base
without container properly attached.
14. Always operate blender with cover in place.
15. Always operate blender with jar pad in place.
16. CAUTION: This blender is not intended for use with hot
liquids or ingredients.
2
17. Do not ll above MAX FILL line for blending.
18. Not for waterjet cleaning.
19. Ensure the jar coupler and motor coupler are aligned and
engaged before operating. If unable to engage, remove jar
and shake contents, then try again.
20. The jar coupler and motor coupler may be hot after running;
do not touch.
21. Replace jar pad if worn.
22. Always use HIGH speed for crushing ice.
23. If the jar overows during blending, there is too much
liquid/ingredients in the jar. Stop blending, remove
enough liquid/ingredients to below MAX FILL line, and
continue blending. Do not operate if overowing.
24. DO NOT use carbonated liquids in the blender jar or any
blending container. Using carbonated liquids in the blender
jar or any blending container may result in injury.
25. DO NOT blend oil or oil-based products such as peanut
butter for more than 5 minutes.
26. Never remove blender jar from base unit until the blade and
coupling have completely stopped.
27. This appliance is intended to be used in households and
similar applications such as:
– Staff kitchen areas in shops, offices and other working
environments;
– Farmhouses;
– By clients in hotels, motels and other residential-type
environments;
– Bed and breakfast-type environments
28. CAUTION: In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
SAVE THESE INSTRUCTIONS
3
GROUNDING INSTRUCTIONS
• For your protection, Waring® Commercial Blenders are
equipped with a 3-conductor cord set.
• 120 volt units are supplied with a molded 3-prong grounding-
type plug and should be used in combination with a properly
connected grounding-type outlet, as shown in Figure 1.
If a grounding-type outlet is not available, an adapter, shown in
Figure 2, may be obtained to enable a 2-slot wall outlet to be
used with a 3-prong plug.
Referring to Figure 3, the adapter must be grounded by attaching
its grounding lug under the screw of the outlet cover plate.
CAUTION: Before using an adapter, it must be determined that
the outlet cover plate screw is properly grounded. If in doubt,
consult a licensed electrician.
Never use an adapter unless you are sure it is properly grounded.
NOTE: Use of an adapter is not permitted in Canada.
BLENDER SPECIFICATIONS
• Capacity: 48 oz. Working Capacity
• Rating: 220-240 Volts, 60 Hz, 13.0 Amps
• Base Material: Polycarbonate
• Bearing: High-Precision Ball Bearing
• Cord: 6-Foot, Three-Conductor Ground Cord with Strain Relief
in Base
• Overall Height: 17 Inches
• cETLus, NSF Listed
• Operating Cycle: 1 min. ON/3 min. OFF
Controls:
TBB145 / TBB160 – LO 20,500, HI 24,000, PULSE 24,000
TBB175 – Variable speed dial from 1,000 to 17,000 RPM with
Pulse, 24,000 RPM
4
PARTS & ASSEMBLY
A. Base
B. Jar Pad
D
C. Container
48 oz., BPA-free copolyester
container.
D. Lid
Center part of the two-piece
lid is removable for adding
ingredients.
E. Blade
Stainless steel cutting blades.
F. Operating Light
Lighted LED indicates that
the unit is in standby mode.
LED will blink during operation.
G. Power Cord (not shown)
Control Panel Variations
TBB145 – Toggle Switch Controls with
HI, LO, OFF & PULSE
TBB160 – Electronic Touchpad Controls
with HI, LO, STOP, PULSE & 60-Second Timer
LED with Up& Down
C
E
B
A
F
TBB145
F
TBB175 – Variable Speed Control Dial & PULSE
PULSE Button Feature
PULSE overrides HI speed for a quick
burst of power.
All parts that come in contact with
food are BPA free.
5
TBB160
F
TBB175
BEFORE FIRST USE
After unpacking, follow the Cleaning and Sanitizing Instructions
on page 9 before rst use and if you have not used your blender
for a period of time. Thoroughly dry the container before placing it
on the base.
in the OFF position, place the
container on the blender base.
Be sure container is fully seated
and that the drive coupling is
properly engaged.
2. Plug the power cord into an
outlet and the LED operating
light will illuminate.
3. Put ingredients into the container and place the lid on top.
Do not ll above MAX FILL line.
4. This blender has 2 speed settings: HI and LO. Switch toggle
switch to desired position. Always use HI or PULSE for
crushing ice.
5. When blending is complete, set toggle switch to OFF
position.
6. This blender is equipped with a PULSE option. Hold toggle
switch in down position to engage PULSE function. Unit will
run on MAX speed until the toggle switch is released.
NOTE: This blender utilizes a Slow Start
™
feature. When
beginning HI or LO operation, the unit will start in a lower speed
for 1 second and then switch to the full selected speed. PULSE
utilizes a .5-second Slow Start
™
. This allows for a more even
blending of ingredients in the container.
7. Allow motor to come to a complete stop before removing
container from blender base. Never place the container
on the motor base or remove it from the motor base while
motor is running.
8. Always hold container with one hand when starting and
while blending. Never operate without lid.
6
9. Wash and dry the container after each use. See Cleaning
and Sanitizing Instructions.
10. Unplug to turn off all power to blender.
TBB160 –
Electronic Touchpad Controls with Timer
Follow steps 1–3 from the TBB145
operating instructions.
4. This blender is equipped with
electronic touchpad controls
with HI, LO, STOP and PULSE
buttons as well as a 60-second
countdown timer. Always use HI
or PULSE for crushing ice.
NOTE: Blender can operate in two
modes: Timer Mode & Continuous Mode.
5. For timer mode, press the
upor down
arrow to set
the desired time on the LED display, up to 60 seconds.
Press and hold the u
por down
arrow for fast scrolling.
After the time is set, press either LO or HI to start the
blender. LED will blink during blending. The timer will count
down to 0 in 1-second intervals and then the blender will
stop. Once you set a time, it will be kept and is repeatable
until reset or unplugged.
NOTE: If you want to increase or decrease the time while the
timer is counting down, press the u
por down
arrow symbols
as needed. Time will increase in 1-second intervals. Pressing the
PULSE or STOP button during timer mode will
stop the motor regardless of how much time is left on the timer.
6. For continuous operation, press either the LO or HI button.
When blending is complete, press STOP. For momentary
operation, press the PULSE button; motor will run on MAX
speed until the button is released.
NOTE: This blender utilizes a Slow Start
™
feature. When
beginning HI or LO operation, the unit will start in a lower speed
for 1 second and then switch to the full selected speed. PULSE
™
utilizes a .5-second Slow Start
. This allows for a more even
blending of ingredients in container.
7. Allow motor to come to a complete stop before removing
container from blender base. Never place the container
7
on the motor base or remove it from the motor base while
motor is running.
8. Always hold container with one hand when starting and
while blending. Never operate without lid.
9. Wash and dry the container after each use. See Cleaning
and Sanitizing Instructions.
10. Unplug to turn off all power to blender.
TBB175 – Variable Speed Controls
Follow steps 1–3 in the TBB145
operating instructions.
4. This blender is equipped with
a Variable Speed Control Dial
that operates from speeds 1–10
and POWER, START/STOP and
PULSE buttons. Always use
Speed 10 or PULSE for crushing
ice.
5. For continuous blending, turn the variable speed control
dial clockwise to set the speed from 1–10. Press the START/
STOP button to start blending. The LED will blink during
blending. When blending is complete, press the START/
STOP button to stop blending. You may wish to start at a
low speed and increase to a higher setting.
6. For momentary operation, press the PULSE button; motor
will run on MAX speed until the button is released.
NOTE: This blender utilizes a Slow Start
beginning HI or LO operation, the unit will start in a lower speed
for 1 second and then switch to the full selected speed. PULSE
™
utilizes a .5-second Slow Start
. This allows for a more even
blending of ingredients in container.
7. Allow motor to come to a complete stop before removing
container from blender base. Never place the container
on the motor base or remove it from the motor base while
motor is running.
8. Always hold container with one hand when starting and
while blending. Never operate without lid.
™
feature. When
8
9. Wash and dry the container after each use. See Cleaning
and Sanitizing Instructions.
10. Unplug to turn off all power to blender.
RESETTING THERMAL PROTECTION
• Your blender is equipped with a manual reset switch to protect
the motor from overheating.
• If your blender stops running under heavy use, or if the LED
light starts to blink much more rapidly than usual during normal
blending, press the power switch to OFF and unplug the power
cord. Empty the blender container of all its contents and allow
approximately 5 to 10 minutes for the motor to cool down.
• Plug the power cord back into the outlet and continue
blending.
• If your blender does not function properly following this
procedure, discontinue use and contact a certied Waring
Customer Service Center.
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH
USE OF THE BLENDER ACCORDING TO THE FOLLOWING
INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF PROCESSED
MATERIAL TO COLLECT ON THE INTERNAL SEALS OF THE
BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use and
whenever it will not be used again within a period of 1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after each
use.
• Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum chlorine
concentration of 100 PPM are recommended.
The following washing, rinsing, and sanitizing solutions, or their
equivalents, may be used.
9
SOLUTIONPRODUCTDILUTION IN WATERTEMPERATURE
WashingInternational
Products
Corporation LF2100
Liquid Low-Foam
Cleaner
RinsingPlain WaterWarm 95˚F (35˚C)
®
SanitizingClorox
Regular Bleach
(8.25% Hypochlorite
Concentration)
1%–2%: 1¼ – 2¾
Ounce/Gallon (lower
dilution of 1% for normal
cleaning and up to 2% for
more stubborn soils)
2 Teaspoons/Gallon
(Alternately a bleach
with 5.25% Hypochlorite
Concentration can be
used at dilution of 3
Teaspoons/Gallon)
Room
Temperature
• In repetitive batch-processing applications, frequent cleaning
of the container will prolong the life of the blade assembly. In
no case should actual running time between cleanings exceed
one-half hour.
• Do not use container to store processed foods or beverages.
TO WASH AND RINSE CONTAINER
1. REMOVE CONTAINER FROM MOTOR BASE. Remove
lid. Rinse container interior and lid under running water.
Add washing solution to container. Scrub and ush out the
container interior and lid to dislodge and remove as much
food residue as possible. Empty container.
2. Wipe down exterior of container with a soft cloth or sponge
dampened with washing solution. Wash lid and lid insert
in fresh washing solution. Fill container one-quarter full
with fresh washing solution, cover (with lid only), place on
motor base and run on HI speed for two (2) minutes. Empty
container.
3. Repeat step 2 using clean rinse water in place of washing
solution.
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING,
TEMPERATURE OF WASHING SOLUTION AND RINSE WATER
10
MUST NOT EXCEED 115˚F (46˚C), AND QUANTITY USED MUST
NOT EXCEED ONE-QUARTER CONTAINER FULL.
TO SANITIZE AND DRY CONTAINER
1. Wipe down exterior of container with a soft cloth or sponge
dampened with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on
motor base, and run on HI speed for one (1) minute. Empty
container. Dislodge any residual moisture from blade
assembly by placing empty container on motor base and
running on HI speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing solution
for two (2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing
is completed. Allow parts to air-dry.
TO CLEAN AND SANITIZE MOTOR BASE
1. UNPLUG POWER CORD. Wipe down exterior surfaces of
motor base with soft cloths or sponges dampened with
washing solution, rinse water, and sanitizing solution.
Prevent liquid from running into motor base by wringing all
excess moisture from cloths or sponges before using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION,
RINSE WATER OR SANITIZING SOLUTION.
2. Allow motor base to air-dry before using.
SERVICE
Refer to the list of Authorized Service Centers enclosed with your
Waring
Center, or write to:
processing of biologically active material, we request that any
items returned for service be sterilized before being shipped.
®
Commercial Blender for the name of the nearest Service
Waring Factory Service Center
P.O. Box 3201
314 Ella T. Grasso Avenue
Torrington, CT 06790
(800) 492-7464
NOTE: If your application involves the
11
Such items must be clearly identied as having been sterilized,
both by a tag on the item itself and by a statement in the
accompanying correspondence. Waring will not accept delivery
of any return unless it is so identied.
Replacement parts for your out-of-warranty repairs are obtainable
at the address below.
WARRANTY
LIMITED TWO YEAR MOTOR WARRANTY
LIMITED ONE YEAR PARTS AND LABOR WARRANTY
(U.S. and Canada Only)
®
Waring warrants every new Waring
free from defects in material and workmanship for a period of
one year from the date of purchase when used with foodstuffs,
nonabrasive liquids (other than detergents) and nonabrasive
semiliquids, providing it has not been subject to loads in excess
of the indicated rating. In addition, the motor in this appliance has
a full two year warranty.
Under this warranty, Waring will repair or replace any part that,
upon our examination, is defective in materials or workmanship,
provided the product is delivered prepaid to the Waring Service
Center at: 314 Ella T. Grasso Ave., Torrington, CT 06790, or any
Factory Approved Service Center.
Commercial Blender to be
This warranty does not: a) apply to any product that has become
worn, defective, damaged or broken due to misuse or due to
repairs or servicing by other than the Waring Service Center or
a Factory Approved Service Center, or due to abuse, misuse,
overloading or tampering; or b) cover incidental or consequential
damages of any kind.
The warranty is applicable only to appliances used in the United
States or Canada; this supersedes all other express product
warranty or warranty statements. For Waring products sold
outside of the U.S. and Canada, the warranty is the responsibility
of the local importer or distributor. This warranty may vary
according to local regulations.
Warning: This warranty is void if appliance is used on Direct
Current (DC).
Waring Commercial
314 Ella T. Grasso Avenue
Torrington, CT 06790
1-800-4-WARING
www.waringcommercialproducts.com
12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.