Waring MX1500XTXP User Manual [en, es, fr]

Hi-Power Blender

licuadora de alta Potencia

Mélangeur Haute Puissance

PREP

MX SERIES

SERIE MX / SÉRIE MX

For your safety and continued enjoyment of this product, always read

the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto, siempre

lea las instrucciones cuidadosamente antes de usarlo.

An que cet appareil vous procure en toute sécurité beaucoup de satisfaction,

lire attentivement le mode d’emploi avant de l’utiliser.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS.

2. Always unplug from outlet when not in use, prior to handling, before

putting on or taking off parts, and before cleaning.

3. To protect against electrical hazards, do not immerse the blender base in water or other liquids.

4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. Children should be supervised to ensure they do not play with the appliance.

5. Avoid contact with moving parts.

6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.

7. The use of attachments, including canning jars, not recommended by the appliance manufacturer may cause hazards.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter or touch hot surfaces.

10. Keep hands and utensils out of container while blending, to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but must be used only when the blender is not running.

11. Blades are sharp. Handle carefully.

12. Always operate blender with cover in place.

13. When blending hot liquids, remove center-piece of two-piece cover. See Hot Blending Instructions.

14. The use of ear protection is recommended during extended operating periods.

15. See Cleaning and Sanitizing Instructions for all Waring Blenders. NOT FOR WATERJET CLEANING.

16. The appliance must be positioned so that the plug is accessible.

17. DO NOT use carbonated liquids in the blender jar or any blending container. Using carbonated liquids in the blender jar or any blending container may result in injury.

18. DO NOT blend oil or oil-based products such as peanut butter for greater than 5 minutes.

19. Never remove blender jar from base unit until the blade and coupling have completely stopped.

SAVE THESE INSTRUCTIONS

MX MECHANICAL SWITCHES

1. Before starting, make sure that the blender is

unplugged and container is not positioned on the blender.

2. Put ingredients into container and cover it. Do not

fill above MAX line.

3. With the unit in STANDBY

container on blender base. Be sure container is fully seated and that drive coupling is properly engaged. Plug blender cord into outlet.

4. This blender has 2 speed settings: HI and LO . Press Paddle Switch

to desired position. To crush ice quickly, use HI speed setting.

5. When finished blending, set paddle switch to STANDBY position.

6. This blender is equipped with a PULSE

down to engage PULSE paddle switch is released.

7. Allow motor to come to a complete stop before removing container from

blender base. Never place the container on the motor base or remove it from the motor base while motor is running.

8. Always hold container with one hand when starting and while blending.

Never operate without jar lid.

9. Wash and dry container after each use. See Cleaning and Sanitizing

instructions.

position, place

option. Hold paddle switch

function. Unit will run on HI speed until the

MX ELECTRONIC TOUCHPAD SWITCHES

WITHOUT SOUND ENCLOSURE

1. Before starting, make sure that the blender is unplugged and container is not positioned on the blender.

2. Put ingredients into container and cover it. Do not

fill above MAX line.

3. Place container on blender base. Be sure container is fully seated and that drive coupling is properly engaged. Plug blender cord into outlet.

4. This blender is equipped with an electronic membrane keypad. The keypad has a main power STANDBY PULSE

5. Press the STANDBY illuminate. For continuous operation, press either LO or HI button. When finished blending, press STOP press the PULSE button is released.

NOTE: Your MX Electronic Blender uses a Slow Start™ feature. When

pressing HI , the unit will start in the LO speed for 2 seconds and then switch to HI speed. This allows for a more even blending of ingredients in container.

buttons.

button to turn on the blender. Green LED will

button; motor will run on HI speed until the

button, plus HI , LO , STOP

. For momentary operation,

and

6. Allow motor to come to a complete stop before removing container from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.

7. Always hold container with one hand when starting and while blending. Never operate without jar lid.

8. Wash and dry container after each use. See Cleaning and Sanitizing Instructions.

9. To turn unit off, press STANDBY

MX ELECTRONIC TOUCHPAD SWITCHES WITH TIMER

1. Before starting, make sure that the blender is

unplugged and container is not positioned on the blender.

2. Put ingredients into container and cover it. Do not

fill above MAX line.

3. Place container on blender base. Be sure container

is fully seated and that drive coupling is properly engaged. Plug blender cord into outlet.

4. This blender is equipped with an electronic membrane keypad. The

keypad has a main power STANDBY and PULSE buttons and a 30-second countdown timer with up and down

5. Press the STANDBY illuminate. The electronic timer will indicate 10 seconds (default). Press the up or down arrow to set the desired time. The electronic timer will indicate run time in 5-second intervals up to a maximum of 30 seconds. After the desired time is set, press HI or LO to start the blender. The timer will count down to 0 in 1-second intervals and blender will shut off. Pressing the PULSE button, the STOP button or the STANDBY regardless of time left on timer.

NOTE: If you want to increase or decrease time while timer is counting

down, press up or down arrows. Time will increase or decrease in 5-second intervals.

6. If the blender is not used for five seconds, the timer function will turn off and return to manual mode. To reactivate timer, press up or down

arrows. When using the electronic timer again, the initial time will be the last time set. Note: If unit has been turned off or unplugged, the timer will default back to 10 seconds.

7. For continuous operation, press either LO or HI button. When finished blending, press STOP . For momentary operation, press the PULSE button. Motor will run on HI speed until the button is released.

NOTE: Your MX Electronic Blender uses a Slow Start™ feature. When

pressing HI then switch to HI speed. This allows for a more even blending of ingredients in container.

arrows to set time.

button to turn on the blender. Green LED will

button will override the timer and the blender will stop

, the unit will start in the LO speed for 2 seconds and

button. Green LED light will go off.

button, plus HI , LO , STOP

8. Allow motor to come to a complete stop before removing container from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.

9. Wash and dry container after each use. See Cleaning and Sanitizing Instructions.

10. To turn the unit off, press STANDBY go off.

MX VARIABLE SPEED OPERATION

Warning – This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

1. Before starting, make sure that the blender is

unplugged and container is not positioned on the blender.

2. Put ingredients into container and cover it.

Do not fill above MAX line.

3. With the unit in STANDBY I position, place

container on blender base. Be sure container is fully seated and that drive coupling is properly engaged. Plug blender cord into outlet.

4. This blender has variable speed controls. Set blender to desired speed

between 1 and 10.

5. The left paddle switch defaults to the VARIABLE setting in order to use

the speed adjustment option. Press right paddle switch up to the ON position.

6. When finished blending, set paddle switch to STANDBY position.

7. This blender is equipped with a PULSE option. Hold left paddle switch

in down position to engage PULSE function. Unit will run on max speed (30,000 RPM) until the paddle switch is released.

8. Allow motor to come to a complete stop before removing container

from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.

9. Always hold container with one hand when starting and while blending.

Never operate without jar lid.

10. Wash and dry container after each use. See Cleaning and Sanitizing

Instructions.

button. Green LED light will

PRE P

MX REPROGRAMMABLE CONTROL SETTINGS

1. Before starting, make sure that the blender is unplugged and container

is not positioned on the blender.

2. Put ingredients into container and cover it. Do not fill above MAX line.

3. Place container on blender base. Be sure container is fully seated and

that drive coupling is properly engaged. Plug blender cord into outlet.

4. The motor speed can be adjusted by pressing the

buttons. Speed ranges from 15% to 100%.

100% 20,000 RPM 50% 10,000 RPM 15% 3,000 RPM

The Speed Up button will increase the motor speed display in 1%

increments and the Speed Down button will decrease the motor speed display in 1% increments. Holding down either button will quickly scroll through speeds.

Using the Speed Up and Speed Down buttons, set desired motor

speed. If no speed is selected, motor will default to 100%.

NOTE: The motor does not run at the newly set speed until the START/

STOP within 5 seconds, the new speed setting will be stored for next use and the blender will return to STANDBY mode; the display will once again read “PRESS ANY BUTTON TO BLEND”.

5. Press START/STOP button to run the blender. Blender will run

continuously at the set speed. The LCD will display the motor speed in percentage. Default speed (percentage) is at 100%. Motor speed can be

changed while blender is running by simply pressing Speed Up or Speed Down button.

6. To stop continuous blending operation, press START/STOP

press any of the program buttons.

button is pressed. If START/STOP button is not pressed

PULSE FEATURES

or Speed

button or

Your unit comes equipped with two PULSE options: Normal Pulse Maximum Pulse

once released, the unit will shut off.

1. To use Max Pulse option, press the button. This will run the motor

at 150% speed. The LCD will read “MAX PULSE SPEED: 150%”.

2. To use Normal Pulse option, press the

at 100% speed. The LCD will read “NORM PULSE SPEED: 100%”.

3. The blender allows you to set the pulse to your desired speed. While

blending at Normal Pulse speed, the motor can be adjusted. To do this, hold the Normal Pulse button and press Speed Up or Speed Down button to adjust the blending speed. The LCD will show the

setting speed and motor speed will change.

NOTE: The speed can be set from 15% to 100%. Once the

button is released, the motor will shut off and the blender will return to standby mode. The changed pulse speed will be stored in memory to replace the default speed at 100%.

. Note: The Pulse buttons are momentary switches –

button. This will run the motor

and

Pulse

REPROGRAMMABLE STATIONS

1. There are 4 Program buttons for four reprogrammable beverage stations for easy operation and consistent results. The factory-set stations are programmed as listed below:

2. To run any of the above preset programs, blender must be in STANDBY mode.

3. Press desired Program button to start the blender. The motor will run at the preset speed within the preset blending time. The LCD will show time remaining. Once the blender counts down to 0, the motor will stop running and the blender will return to STANDBY mode and prompt “PRESS ANY BUTTON TO BLEND”.

NOTE: To terminate a blending program, simply press START/STOP

button or any of the Program buttons. After doing this, the blender will return to STANDBY mode and LCD will prompt “PRESS ANY BUTTON TO BLEND”.

REPROGRAMMING BEVERAGE STATIONS

Users can add 4 new programs to meet their needs. A program can consist of several sections, each with a different speed and running time. For example, as shown below:

Section 1: speed = 75%; time = 30 seconds Section 2: speed = 100%; time = 20 seconds Section 3: speed = 50%; time = 20 seconds

The program has the following limitations: Speed: 15% to 100%

Time: 5 to 90 seconds Total running time in a program cannot exceed 90 seconds, i.e., sum of the sections cannot be longer than 90 seconds.

can be replaced with a new program that has 3 sections,

Liquid drinks Frozen drinks Ice cream drinks Smoothies

NOTE: The during the reprogramming process.

1. To enter new program, press both Speed Up

buttons simultaneously while unit is in STANDBY mode. The blender will enter new programming mode and the LCD will prompt “ADD NEW PROGRAM”.

2. Next, you will need to set values. Press the Program button you want

to replace (i.e., 1... 4). The LCD will prompt “USE UP/DOWN TO SET SPEED: 25%”.

button will act as the enter key to proceed to next step

and Speed Down

NOTE: 25% is the default speed setting in the reprogramming mode.

3. Press Speed Up or Speed Down button to set the speed value. The increment is 1% (150 RPM). Press and hold the button to quickly scroll through speeds. The speed can be set between 15% and 100%.

4. Once required speed is reached, press button or wait 5 seconds to confirm setting. The LCD will now prompt “USE UP/DOWN TO SET TIME”. NOTE: Five seconds is the default time setting in the reprogramming mode.

5. Use Speed Up 90 seconds). Once 90 seconds are reached, pressing Speed Up

not increase the value and the LCD will prompt “MEMORY LIMIT” for 2 seconds.

6. Press button or wait 5 seconds to confirm the setting. When the blending time is confirmed, the LCD will prompt SELECT ANOTHER SPEED. Repeat steps 3–5 if additional processing is needed.

NOTE: When pressing Speed Up speed for next section, the LCD will prompt “USE UP & DOWN TO SET SPEED: 25%”.

7. To save the new program settings, press both Speed Up and Speed Down buttons simultaneously. The LCD will prompt NEW PROGRAM

(PROG #) SAVED for 5 seconds. The blender will return to STANDBY mode and the LCD will prompt “PRESS ANY BUTTON TO BLEND”.

NOTE: If no button is pressed for 60 seconds when prompted to “ADD

NEW PROGRAM”, the blender will exit NEW PROGRAM mode and will return to STANDBY mode. The new program will not be stored.

8. To run new programs, simply press the desired Program button and the blender will run the program set by the user. The LCD will display NEW PROGRAM # and will count down the set time.

RESTORING FACTORY-SET BEVERAGE STATIONS

or Speed Down button to set the time value (up to

will

or Speed Down buttons to set

1. To restore factory-set default beverage stations, press both Speed Up

PROGRAM.

2. Press

3. Press 3 seconds.

4. The unit will return to STANDBY mode and the LCD will prompt PRESS ANY BUTTON TO BLEND.

NOTE: The STOP

restoring default programs is confirmed.

and Speed Down buttons. LCD will prompt ADD NEW

button. LCD will prompt RESTORE DEFAULT PROGRAMS.

button to confirm and save. The LCD will display the logo for

key will abort this process at any point before

DRINK COUNTER

Your reprogrammable blenders are equipped with a drink counter to keep track of daily drink totals and total drink counts for your machine. To display the counts, hold program buttons Your display will read:

DAILY COUNT XXXX TTL COUNT XXXXX

Daily Count will display the numbers of drinks mixed per day. Total Count is the accumulation of all drinks made since first use of the blender. The Daily Count can be reset by holding in Program buttons simultaneously for 3 seconds then, pressing ON/OFF button for 3 seconds. Daily Count will reset to zero and Total Count will remain unchanged.

If Total Count needs to be reset, call your nearest Waring authorized service facility for information.

NOTE: Use of the PULSE features will not add to the daily or total drink counts.

RESETTING THERMAL PROTECTION

• The blender you have purchased is equipped with an Automatic Reset Switch to protect the motor from overheating.

• If your blender stops running under heavy use, turn the power switch to the STANDBY or OFF position and unplug the power cord. Empty the blender container of all its contents and allow approximately 5 minutes for the motor to cool down.

• Plug the power cord back into the outlet and continue blending.

simultaneously for 3 seconds.

IMPORTANT - HOT BLENDING INSTRUCTIONS

To minimize the possibility of being scalded when blending hot materials, the following precautions and procedure must be observed.

• Hot materials are those that are 100°F (38°C) or hotter.

• Limit the amount of materials processed to 1 pint.

• Completely remove the center portion of the two-piece container lid before starting motor (this will allow venting of the rapidly heated and expanded air inside the container when blender is running).

• Always start blending on lowest speed setting, and then progress to desired speed.

• Never stand directly over blender when it is being started or while it is running.

INSTALLING THE SOUND ENCLOSURE

NOTE: If you are installing a sound enclosure as an optional accessory,

remove the standard jar pad to access the screw holes on the upper housing. This jar pad will not fit properly with the sound enclosure. To remove it, peel it back, starting in the corner and working your way over the drive coupling until it is completely off the base unit, as seen in Figures 1, 2 and 3.

Figure 1 Figure 2 Figure 3

Figure 6

Figure 11 Figure 12

Figure 7

Figure 8 Figure 9

Figure 13

Figure 4

Figure 14

Figure 5

Figure 10

Figure 15

Once you have finished removing the standard jar pad OR if your blender came packed with a sound enclosure, follow these instructions: Step 1: Find the 3 screw holes located on the left, back and right sides of

the upper housing as seen in Figures 4, 5 and 6.

Step 2: Place the base of the sound enclosure on the motor housing so the

screw holes on the enclosure line up with the screw holes on the base. Use a Phillips-head screwdriver and the 3 screws included with sound enclosure to secure the enclosure to the base unit in the 3 locations as seen in Figures 7, 8 and 9.

Step 3: Once the sound enclosure is secured tightly, select the custom jar

pad (included with sound enclosure). Please note the standard jar pad will NOT fit properly with the sound enclosure. The correct custom jar pad has a recessed area around the outer edge. It also has a curved front with tabs on the sides, as seen in Figures 10, 11, and 12. This curved area should face the front of the blender.

Step 4: Attach custom jar pad included with sound enclosure onto upper

housing with the curve facing out, as seen in Figure 13. Press tightly around coupling to secure custom jar pad onto upper housing, as seen in Figures 14 and 15.

REMOVING THE SOUND ENCLOSURE

To remove the sound enclosure, unplug your blender and follow these steps:

1. Open sound enclosure and remove blender container.

2. Remove front portion of sound enclosure by disengaging both sides at the pivot point.

2. Remove rubber jar pad.

4. Remove 3 screws from blender base and remove sound enclosure.

TURNING OFF YOUR BLENDER

Whether your blender is in STANDBY mode, NEW PROGRAM mode, or the motor is running, pressing the ON/OFF from running and will turn the power off. The LCD display will turn off.

NOTE: All programs and current settings will be restored next time you turn unit on.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS. FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.

• Wash, rinse, sanitize and dry container prior to initial use and whenever

it will not be used again within a period of 1 hour.

• Wash and rinse container after each use.

• Clean and sanitize motor base prior to initial use and after each use.

• Washing solutions based on non-sudsing detergents and chlorine-based

sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents, may be used.

button will stop the unit

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE

Washing Diversy Wyandotte 4 Tablespoons/ Hot 46˚C

Diversol BX/a or CX/A 3.8 Litres

Rinsing Plain Water Warm 35˚C Sanitizing Clorox® 1 Tablespoon/ Cold 10 –21˚C

Institutional Bleach 3.8 Litres

• In repetitive batch-processing applications, frequent cleaning of the

container will prolong the life of the blade assembly. In no case should actual running time between cleanings exceed ½ hour.

• Do not use container to store processed foods or beverages.

+ 25 hidden pages