Waring 700G Operator’s Manual

Service

Refer to the list of Authorized Service Centers enclosed with your Waring blender for the name of the nearest Service Center, or Write to:

Waring Factory Service Center 314 Ella T. Grasso Ave.

Torrington, CT 06790 [phone]

Ship blenders for repair to the above address or to an Authorized Service Center. Do not ship to a Waring Sales Office.

Note: If your application involves the processing of biologically active materials we request that any items returned for service be sterilized before being shipped. Such items must be clearly

identified as having been sterilized both by a tag on the item itself and by a statement in the accompanying correspondence. Waring will not accept delivery of any returns unless they are so identified. Replacement parts for your own “Out of Warranty” repairs are obtainable at the above address.

WARRANTY

Waring warrants every new WARING COMMERCIAL BLENDER to be free from defects in material and workmanship for a period of one year from the date of purchase when used with foodstuffs, non-abrasive liquids (other than detergents) and non-abrasive semi-liquids, providing it has not been subject to loads in excess of the indicated rating.

Under this warranty, the Waring Commercial Division will repair or replace any part which, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service Center at Torrington, CT 06790, or any Factory Approved Service Center.

This warranty does not: a) apply to any product which has become worn, defective, damaged or broken due to use or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Service Center or due to abuse, misuse, overloading or tampering; b) cover consequential damages of any kind.

This warranty gives you specific legal right, and you may have other rights which vary from state to state so that certain limitations or exclusions set forth above may not apply to you.

WARNING: This warranty is VOID if appliance is used on Direct Current (D.C.) or if the appliance has not been registered.

WARING COMMERCIAL

314 Ella T. Grasso Ave.

Torrington, CT 06790 www.waringproducts.com

004589 RV19 1008

10WC116188

BLENDER

OPERATION MANUAL

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

1.READ ALL INSTRUCTIONS.

2.To protect against electrical hazards, do not immerse the blender

base in water or other liquid.

3.Close supervision is necessary when any appliance is used by or near children.

4.Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.

5.Avoid contacting moving parts.

6.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any

manner. Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.

7.The use of attachments including canning jars not recommended by the appliance manufacturer may cause hazards.

8.Do not use outdoors.

9.Do not let cord hang over edge of table or counter, or touch hot surfaces.

10.Keep hands and utensils out of container while blending to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used but must be used only when the blender is not running.

11.Blades are sharp. Handle carefully.

12.If your blender utilizes a removable jar base and blade assembly, to avoid injury never place cutting assembly cutting blades on base without container properly attached.

13.Always operate blender with cover in place.

14.When blending hot liquids, remove center piece of two-piece cover on those units supplied with this construction. See Hot Blending Instructions

SAVE THESE INSTRUCTIONS

	Blender
	One Quart Capacity Specifications
• Ratings	120 VAC – 50/60Hz – Single Phase
	230 VAC – 50Hz – Single Phase
• Motors	Permanently lubricated series-wound universal type
• Timer	Selective timer cycle from 1 to 180 seconds for
	automatic continuous running
• Bases	Zinc die casting with epoxy enamel finish or polished
	stainless steel
• Containers	Stainless steel, borosilicate glass, polycarbonate or
	san plastic
• Cord	6 foot – 18 gauge – three conductor grounded cord with
	strain relief

Grounding Instructions

•For your protection, Waring Commercial Blenders are equipped with a

3-conductor cordset.

•120 Volt units are supplied with a molded 3-prong grounding-type plug and should be used in combination with a properly connected grounding-type outlet

If a grounding-type outlet is not available, an adapter, shown in Figure 2, may be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug.

Referring to Figure 3, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.

Caution: Before using an adapter, it must be determined that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician. Never use an adapter unless you are sure it is properly grounded.

Note: Use of an adapter is not permitted in Canada.

Green/Yellow: Earth Ground

Blue: Neutral

Brown: Live

Operation

This piece of equipment is designed for the high speed blending, pulping, mixing or reducing of animal tissue, vegetables, foodstuffs, plant materials and other substances. A typical operating sequence is as follows:

1.Add materials to be processed to container.

2.Place cover on container.

3.With the power switch on OFF position, place container on blender. Be sure container is fully seated and the drive coupling is properly engaged.

4.Set power switch to ON, Low or High position.

5.When finished processing, set power switch to OFF position.

6.Allow motor to come to a complete stop before removing container from blender.

Note: Containers with removable bottoms have left-handed threads. To tighten, turn in direction of molded arrow on underside of removable bottom. When reassembling, be sure rubber gasket is positioned between the container and the flange on the blade assembly.

Important

HOT BLENDING INSTRUCTIONS

To minimize possibility of scalding when blending hot materials, the following precautions and procedures must be observed.

1.Limit amount of material processed to 1/2 pint.

2.Completely remove the center portion of the two-piece container lid before starting motor. (This will allow venting of the rapidly heated and expanding air present inside container when blender is running.)

3.Always start blending lowest speed setting, then progress to desired speed.

4.Never stand directly over blender when it is being started or while it is running.

To Operate Timer Model Only