WAREMA External venetian blind Installation Instructions Manual
WAREMA external venetian blind
with auxiliary motor and battery-operated
emergency retraction set
cable guidance
Installation instructions
For qualified technicians only
Valid from 22 June 2012
Document no. [M2001452_0] – EN
Table of contents
[M2001452_0] - EN / 22.06.12 Page 2 of 20 Subject to change without notice
Table of contents
1 Introduction ....................................................................................................................... 3
1.1 Information on safety ....................................................................................................................................... 3
1.2 Explanation of symbols and signs ................................................................................................................... 3
1.3 Important safety information ............................................................................................................................ 4
1.4 Information on the target group and application of these instructions .............................................................. 5
2 Product information ........................................................................................................... 6
2.1 Parts description .............................................................................................................................................. 6
2.2 Technical data/accessories ............................................................................................................................. 6
2.3 Intended use .................................................................................................................................................... 7
2.4 Wind speed limits ............................................................................................................................................ 8
2.5 CE conformity .................................................................................................................................................. 8
3 Installation ......................................................................................................................... 9
3.1 Tools ............................................................................................................................................................... 9
3.2 Unpacking the external venetian blind ........................................................................................................... 10
3.3 Scope of delivery ........................................................................................................................................... 10
3.4 Marking the position of the external venetian blind ........................................................................................ 10
3.5 Mounting the bracket/top rail bracket ............................................................................................................ 11
3.6 Preparing the feedthrough for the power line ................................................................................................ 13
3.7 Attaching and centring the top rail ................................................................................................................. 14
3.8 Securing the top rail ...................................................................................................................................... 14
3.9 Overview of the fixation possibilities of the tension cable (optional) .............................................................. 15
3.10 Attaching the tension cable using the tension cable bracket/tension cable holder ........................................ 15
3.11 Attaching the tension cable with the plastic spring tension device ................................................................ 17
3.12 Performing a functional check with the external venetian blind ..................................................................... 18
3.13 Final tasks ..................................................................................................................................................... 19
Introduction
[M2001452_0] - EN / 22.06.12 Page 3 of 20 Subject to change without notice
1 Introduction
1.1 Information on safety
It is important to follow these instructions in the interests of personal safety. Failure to comply with these
instructions when operating the product may result in
personal injury and/or property damage. Failure to
comply with these instructions relieves WAREMA of liability.
Warnings are marked with these symbols in
the instructions.
Read the instructions carefully before
starting with the installation.
Read and observe all warnings.
Please observe all safety, installation,
operating and setting instructions.
Observe all warnings on the product.
1.2 Explanation of symbols and signs
Safety information and symbols are contained in the appropriate parts of the text.
Symbol Use/explanation
DANGER
Identifies an imminent danger that may
result in death or serious injury if not prevented.
WARNING
Identifies a potential danger that may result
in death or serious injury if not prevented.
CAUTION
Identifies a potential danger that may result
in minor injury or property damage if not
prevented.
Read the installation instructions.
)
Note
Important information on how to proceed
and on the content of these instructions.
Activity/step
`
List
Introduction
[M2001452_0] - EN / 22.06.12 Page 4 of 20 Subject to change without notice
1.3 Important safety information
The safety instructions and warnings described here are
intended to safeguard your health as well as protect the
product. Please read the following points carefully.
Damage resulting from inappropriate use or the failure to
observe these instructions or safety information is not
covered by the guarantee. Liability will not be accepted
for secondary damage.
General conditions
If the external venetian blind with auxiliary motor and battery-operated emergency retraction set is used at escape
doors and emergency windows to protect against summer heat and glare and to provide privacy, the batteryoperated emergency retraction set is activated in case of
an emergency to clear the escape route.
Correct functioning of the external venetian blind with auxiliary motor and batteryoperated emergency retraction set and,
therefore, unblocking of the escape doors
and emergency windows in case of an
emergency are only ensured if you follow
our safety instructions closely.
Danger to life and limb if the WAREMA
control is not used!
It must be ensured that the external venetian
blind is only activated by the associated
electronic battery-operated control. Manipulations by third parties must be
excluded. It is important that the external
venetian blind is not blocked by dirt or
obstacles.
Danger to life and product damage from
incorrect procedure during commissioning! If the following points are not followed,
no warranty can be granted for functional
problems, soiling and damage.
The external venetian blind must remain
out of service until the commissioning has
been released.
Raise the external venetian blind fully to
clear the escape route. The external venetian blind is sufficiently raised if the external venetian blind disappears into the
cover panel (if present), or if the escape
door or emergency window can be opened.
Installation preparations
Danger to life from restrictions of the escape
route while during installation of the external
venetian blind with auxiliary motor and battery-operated emergency retraction set! Before beginning installation, inform the safety
officer that the escape route is available only
to a limited extent. It must be ensured that the
building can be evacuated along a different
escape route.
Risk of injury and damage to the product
from incorrect installation!
Comply with the specified installation
steps and instructions.
Install the product only if it is in technically
perfect condition.
Before installation, check the mounting
substructure to make sure it can bear the
loads.
Widely cordon off the installation site and
the projection area of the external venetian blind.
Packaging
Risk of suffocation! Do not leave the packa-
ging material lying around, and keep children
away from small parts. Plastic film, polystyrene, small parts, etc., can be very dangerous
for children to play with.
Electrical connection
Electric shock from incorrect installation!
The electrical installation must be performed
by a certified electrician in accordance with
the electrical installation regulations published
by the Association of German Electrical Engineers (VDE 0100) or the standards and regulations of the country in which the product is
being installed. The specialist must observe
the installation instructions included with the
electrical appliances. Before commissioning
the product, remove all lines that are not required. Disconnect any devices that are not
needed for operation.
Introduction
[M2001452_0] - EN / 22.06.12 Page 5 of 20 Subject to change without notice
Risks posed by the product
Risk of crushing and injury! When raising
and lowering the product and when making
the electrical connection of the system, do not
reach into movable parts (e.g. between the
bottom rails and/or slats).
Risk of damage to the product
Risk of injury from unmonitored or improper operation of the external venetian
blind. Install the operating elements of the
product and the emergency push button of the
external venetian blind with auxiliary motor
and battery-operated emergency retraction
set outside of the projection area but within
view of the product at a height that meets the
national regulations for the disabled. Instruct
customers on how to use the product.
Product damage and property damage
from carelessness during operation! The
projection area of the external venetian blind
must be kept clear of fixed and movable
obstacles.
Transport
Risk of injury and product damage from
inappropriate transport! The gross axle
weight rating and gross weight rating of the
transport vehicle must not be exceeded. A
loaded vehicle may handle differently.
Secure the transported goods appropriately and safely.
Protect the packaging of the product against moisture.
Soaked packaging may work loose and cause accidents.
1.4 Information on the target group and application of these instructions
Target group
These installation instructions are intended for qualified fitters. Knowledge of safety at work, accident pre-
vention regulations, working with ladders and scaffolding,
handling and transporting long and heavy items, using
fixation materials, assessment of the building fabric,
commissioning and operation of the product is required. If
any of these qualifications are unavailable, the work must
be carried out by a specialist fitting company.
The electrical installation must be performed by a certified
electrician in accordance with the electrical installation
regulations published by the Association of German
Electrical Engineers (VDE 0100) or the standards and
regulations of the country in which the product is being
installed.
Contents
These instructions are part of the operating manual and
are an integral part of this product. These instructions
contain important information on transport, handling, installation and commissioning of this item. They describe
the basic installation of the WAREMA external venetian
blind with auxiliary motor and battery-operated emergency
retraction set and rail guidance. Other versions or special
solutions are not dealt with.
Permissible activities
Aside from the activities described for the product in these
installation instructions, alterations, additions and maintenance work on the product are not permitted without the
written approval of WAREMA.
Product information
[M2001452_0] - EN / 22.06.12 Page 6 of 20 Subject to change without notice
2 Product information
2.1 Parts description
dd200005240
1 Top rail 6 Bottom rail
2 External v ene tian blind
d
rive (motor)
7
Tilting tape
3 Auxiliary motor 8 Emergency push but-
ton*
4 Tension cable 9 Battery-operated con-
trol*
5 Slat 10 Lifting tape
Fig. 1: Parts overview for the external venetian blind with
auxiliary motor and battery-operated emergency retraction set and c
able guidance
* The emergency push button and the battery-
operated control together make up the emergency
retraction set
2.2 Technical data/accessories
Weight Value
Flat slat Approx. 2.7 kg/m²
Beaded slat Approx. 3.1 kg/m²
Dim-out slat Approx. 3.2 kg/m²
Tab. 1: Weights for external venetian blind
Data for electric drive (external venetian blind drive)
Parameter D339
Rated torque 9 Nm
Power 131 W
Current consumption 0.57 A
Rated speed 26 rpm
Rated voltage 230 V AC
Frequency 50 Hz
Degree of protection IP 54
Short-term operation (S2) 4 minutes
Limit switch range 97 revolutions
Tab. 2: Details on the external venetian blind drive
)
NOTE
The technical data on the control can be found in
the associated installation instructions.
Accessories
A wide range of control devices is available for the sun
shading system to give you optimum control of the product. These controls can be combined with the
emergency retraction system. However, this must be
clarified on a case by case basis.
Do not use the external venetian blinds in icy or frosty
weather. Liability cannot be accepted for damage to the
sun shading system resulting from the operation under icy
conditions. We recommend using an ice monitoring system.
Loading...