Wansview NCM620W, NCM625W, NCM626W, NCM621W, NCM622W User Manual
...
IP
IP
Camera
Camera
((SmartP2P
SmartP2P))
NCM
NCM
series
series
User
User
manual
manual
October 2014
Rev 1.2
Please read and understand this manual
before attempting installation of the product.
http://www.wansview.com
2
Statement
If the user manual doesn’t help you to resolve the problem, please call our technology center
for technical support.
Notice
1、 Installation Environment
Keep away from the places for high-temperature, heat source and direct sunlight;
Keep away from water and if wet, cut off the power immediately.
Avoid using in a damp environment; the reference range for operation humidity is below
85%RH.
Avoid using in too hot and too cold environment, the reference range for operation
temperature is -10℃~ +50℃
Please install it horizontally or wall mount, avoid strenuous vibration and do not place
other items on top of the unit.
2、 Transport and Handling
Please handle the item with care.
Do not use in areas around condensation.
Please disconnect the item from the mains before moving.
Notice:
1. Be careful not to damage the camera or subject it to strong impacts or shocks.
2. Do not touch the optical components for the image sensor, such as the lens, if
necessary, please place a clean and moistened cloth with alcohol and wipe the dirt
gently; When not in use, please place the dust cover on to the item to protect the image
sensor.
3. Do not aim the camera directly into the sun or at other intense light sources that could
affect the image quality, this will also shorten the service life for the image sensor.
4. Keep away from laser when it is working, otherwise the image sensor can be damaged.
5. If the equipment is not working properly, please contact the store or the service centre,
do not disassemble or modify the equipment in any way.
http://www.wansview.com
3
Index
1. PRODUCT INTRODUCTION........................................................................................................5
1.1. PRODUCT SUMMARY.................................................................................................................. 5
1.2. PACKAGE FOR TYPICAL PRODUCTION.........................................................................................5
2. INSTALLATION AND OPERATION GUIDE.............................................................................. 8
2.1. VIEW VIDEO BY MOBILE PHONE SOFTWARE................................................................................8
2.2. VIEW VIDEO BY WIRED CONNECTION IN LAN............................................................................8
2.3. VIEW VIDEO BY WIFI CONNECTION IN LAN............................................................................ 11
2.4. VIEW VIDEO IN INTERNET.........................................................................................................12
2.5. VIEW VIDEO BY PC CLIENT SOFTWARE.................................................................................... 14
2.6. VIEW VIDEO BY OTHER WAY.................................................................................................... 14
2.6.1. Other Web Browser.........................................................................................................14
2.6.2. Other common software.................................................................................................. 15
3. ALL SETTINGS............................................................................................................................ 15
3.1. VIDEO SETTING........................................................................................................................ 15
3.1.1. Video parameters............................................................................................................ 16
3.1.2. Audio parameters............................................................................................................17
3.1.3. Image parameters........................................................................................................... 17
3.2. WEB SETTING........................................................................................................................... 18
3.2.1. Basic web setting............................................................................................................ 18
3.2.2. WIFI setting.................................................................................................................... 18
3.2.3. WAN access setting......................................................................................................... 18
3.2.4. ONVIF setting................................................................................................................. 19
3.3. ALARM SETTING...................................................................................................................... 19
3.3.1. External Alarm Input...................................................................................................... 19
3.3.2. Motion Detection Setting................................................................................................ 20
3.3.3. Alarm mode setting......................................................................................................... 20
3.3.4. Alarm time setting...........................................................................................................21
3.4. ADVANCE SETTING...................................................................................................................21
3.4.1. User management........................................................................................................... 21
3.4.2. Auto Capture Setting....................................................................................................... 22
3.4.3. Timer recording...............................................................................................................22
3.4.4. E-mail Setting................................................................................................................. 22
3.4.5. FTP setting......................................................................................................................23
3.4.6. Multiple settings..............................................................................................................24
3.5. SYSTEM SETTING...................................................................................................................... 24
3.5.1. Device information......................................................................................................... 24
3.5.2. Date and time setting...................................................................................................... 25
3.5.3. Initialize setting.............................................................................................................. 25
3.5.4. System Log...................................................................................................................... 25
4. PRODUCT FAMILY FOR SMARTP2P CAMERA.................................................................. 26
http://www.wansview.com
4
4.1. HD PTZ CAMERA NCM620W................................................................................................ 26
4.2. HD WATERPROOF CAMERA NCM621W...................................................................................27
4.3. HD PTZ CAMERA NCM622W................................................................................................ 27
4.4. HD CUBE CAMERA NCM623W.............................................................................................. 28
4.5. HD PTZ CAMERA NCM624W................................................................................................ 29
4.6. HD PTZ CAMERA NCM625W................................................................................................ 29
4.7. OUTDOOR HD WATERPROOF PTZ CAMERA NCM626W.........................................................30
4.8. HD HEMISPHERE CAMERA NCM627.......................................................................................31
4.9. HD WATERPROOF CAMERA NCM628W................................................................................. 31
4.10. HD CUBE CAMERA NCM629W.............................................................................................. 32
4.11. HD PTZ CAMERA NCM630W................................................................................................ 33
4.12. HD PTZ CAMERA NCM631W................................................................................................ 33
http://www.wansview.com
5
1. Product introduction
1.1. Product summary
Thank you for choosing this high definition SmartP2P IP Camera, the IP Camera
combines a high definition digital video camera with network connectivity and a powerful
web server to bring high definition video to your desktop from anywhere on your local
network or over the Internet. It is very suitable for family, shops, office and so on.
Main features:
Support Plug and Play function, view video via free iSmartviewPro mobile
phone or PC client software.
Support 3 kinds of H.264 video stream and 1 way MJPEG video stream
simultaneously, suitable for Local, Internet and Cross-platform view;
Support resolution for 1280*720/640*360/320*180;
Support 4 ways view in a video stream;
Support two-way intercom function, and G.711 and G.726 audio encoding;
Support 802.11b/g/n protocol, build-in WiFi module to perform wireless
monitoring;
Support max. 32G SD/TF card for storing the alarm video and pictures, timing
snapshot and recording;
Built-in web server, use one port to send all the data, users can facilitates
network setting;
Support ONVIF and RTSP protocol, easy to integrate it to NVR or large client
software;
Support WPS/QSS function;
Support POE function for some cameras, user optional;
Support multi-languages web interface, support 1/4/9 split screen to perform
several view at same time;
Manufacturer puts a label of DDNS at the bottom of each IP Camera. When IP
Camera is connected to the internet, this URL can be used to visit the device;
Provide free client software, support Multi-view, Long time recording, video
replay etc;
1.2. Package for typical production
Accessory
Type
Power
adaptor
CD
Network
Cable
Bracket
Stand
of
plastic
Antenna
NCM620W
5V
√√√√√
http://www.wansview.com
6
NCM621W
12V√√√√
√
NCM622W
5V√√√√
√
NCM623W
5V√√√√
-
NCM624W
5V√√√√
√
NCM625W
5V√√√√
√
NCM626W
12V√√-√
√
http://www.wansview.com
7
NCM627W
12V√√-√
-
NCM628W
12V√√√√
√
NCM629W
5V√√√√
-
NCM630W
5V√√√√
-
NCM631W
5V√√√√
√
Notice:
If you choose IP camera with wireless function, so it includes wifi module inside
the camera and antenna in package.
Please check carefully if all listed items are included in the package, if anything
missing, please contact vendor in time.
http://www.wansview.com
8
2. Installation and Operation Guide
2.1. View video by mobile phone software
You need to download and install iSmartviewPro mobile phone client software from
attached CD, and then scan QR code on the camera body to add camera for viewing video, for
detail, please see “Product Quick Application Guide”.
2.2. View video by wired connection in LAN
Power on the IP camera（please check carefully the voltage of power adaptor, don’t
insert incorrect power, otherwise it will be damaged）, connect IP camera to router by
network cable and connect computer to the same router, example of figure 1.
Figure 1
Insert attached CD to computer driver, double click “H&MSearch_en.exe” in the CD,
will pop up the interface as figure 2, please operate as the following steps:
Router
LAN Computer
IPcamera
http://www.wansview.com
9
Figure 2
1) Click “Search”（Please make sure your firewall will not block up the item to be
searched）
2) Choose a camera;
3) Change the ip address of the ip camera according to the information in the red
frame on the left. The numbers in the red circle should not be the same. The
Http port should be a number between 80~65535;
4) Enter user name and password for the device, the default is “admin” and
“123456”;
5) Click “update”;
6) After updating successfully, click “Search (F3)”, choose the device again and
click “Browse (F4)”. Then you can run the web browser, enter user name and
password and login IP camera to view the video, example of figure 3.（please
use IE browser at first time）
http://www.wansview.com
10
Figure 3
Notice: Need to download ActiveX when first use, click “download ActiveX( when first
use)” in figure 3, will display prompt as figure 4, click ‘run’ will download and install the
ActiveX automatically.
Figure 4
Tips: You can hold on reset button on the camera for 10 seconds to restore factory
default if you forget user name and password, or not sure the device parameters.
Click “Video View” in figure 3 to access video interface as below.
1) Status bar
Figure 4-1
1 Display connection status;
2 Display record status: if click “Record”, it will show “REC” which stands for
http://www.wansview.com
11
recording; click record button again, it will stop;
3 Zoom out, zoom in and restore digital zoom;
4 Set saving file path: set the location for recording and capturing file storage;
5 Talk button: Click this button to hear what the person at the side of computer
talks. Click it again, it will stop playing;
6 Audio monitor button: Click this button to hear what people talking about at the
side of IP Cameras,
2) Choose video stream
You can choose primary stream or second stream, third stream to view the video.
Recommend to view by primary stream in LAN, by second stream in WAN and by third
stream in mobile phone.
You can view the video by four, nine pictures in same screen, but need to set the camera
in 3.6.6 multiple setting.
3) PTZ control
If the camera supports PTZ function, you can click up, down, left, right arrow to control
the camera moving, click button to center and stop the camera.
When you set camera to a preset position, and then click ‘ , after the camera is
changed to other direction, click can move the camera to the position you have
set.
4) Snap /record / SD card/playback
Click “Snap” button, to save the picture to the specified file.
Click “Record” button to start record. Click again to stop record.
Click “Check TF/SD card” can browse the files in the SD card (If the SD card
already inside the camera), you can select file to download it;
Click “Playback” button, it will show a player which can play the record video.
For these buttons means: play; stop; open video file; slow
play; quick play.
2.3. View video by WiFi connection in LAN
After finishing the wired connection as chapter 2.2, you can connect the camera by WiFi.
Login camera in wired connection and enter wifi setting, and then operate as the
following step, example of figure 5.
Loading...