WangYuan HJ1007 User Manual

1

ROBOTIC POOL FLAT FLOOR

CLEANER HJ1007

USER MANUAL

Subject to update by manufacturer without prior notice

2

Important Precautions

1. This model applies to swimming pool with flat floor.

2. Do not power on the unit when it is outside of the water.

3. Make sure the power cord is connected to a leakage protective device and appropriate earthed socket.

4. Do not operate the cleaner when there is people in pool.

5. Do not try to move the floaters along the electric cable. Leave them always in the original positions.

6. Before power on, make sure the cable is fully released to avoid any winding, which could affect the

cleaner’s performance or cause damage.

7. The filter tray should be cleaned after use. This will prevent the dirty filter tray affecting the normal

operation of the cleaner.

8. The cleaner should be stored in a cool and ventilated place, away from direct sunlight.

9. The power supply unit should be placed in a shaded area. In order to avoid overheating and the potential

damage of components, never cover the power supply unit.

10. Only authorized personnel should open the cleaner’s motor assembly and power supply unit, fail to do

which will cause a invalid warranty.

11. In order to avoid any accident/damage, the power supply unit should be steadily placed at a minimum

distance of 3.5m from the pool edge.

12. Do not use the cleaner beyond the working environment/conditions stated in this manual. Read this

manual carefully before use.

13. Do not uncover the button film on the power supply unit.

14. Close the filtering system of your pool when use this cleaner.

15. Slightly water pollution may occur in case grease in motor seal oil leaks.

16. This model only applies to small pools that corresponding to cleaner’s cable length, there is risk for the

cleaner to work in a too big pool to cause pulling the cleaner upside down by the limited cable.

17. Make sure the power unit be properly positioned for the cleaner to cover as large as pool surface and in

the meantime cleaner has surplus cable once touching the pool end.

3

Note

1. Putting into or lifting out from pool with the cleaner bottom toward the wall to avoid any

possible scratch to the pool surface.

2. Install the brush before use to avoid possible dirt leaks.

4

Contents

Ⅰ. Introduction································································································P. 4

Ⅱ. Safety········································································································P. 4

Ⅲ. Specifications·····························································································P. 4

Ⅳ. Cleaner Structure························································································P. 5

Ⅴ. Operation Instructions·················································································P. 6

Ⅵ. Trouble Shooting·························································································P. 18

Ⅶ. Packing List································································································P. 19

Ⅷ. Packing List································································································P. 20

5

Ⅰ. Introduction:

The automatic swimming pool floor cleaner HJ1007 is a new type of highly efficient swimming pool

cleaning equipment. Through its advanced computer controlled program, it can clean the pool floor

automatically without draining pool water. At the same time, it filters the pool water and gets rid of

suspended particles and sediments.

For safe operation, the cleaner works on DC 24V.

Please read this instruction manual carefully before use.

. Safety:Ⅱ

1, Position requirement of power supply unit：Refer to item 9 and 11 in “Important Precautions”.

2, Requirement of power: Refer to item 3 in “Important Precautions”.

Make sure the cleaner corresponds to your local voltage and frequency (hertz).

Ⅲ. Specifications:

1. Rated input voltage and frequency: 220V/50Hz

2. Output Voltage: DC24V

3. Rated output power: 150W

4. Working cycle: 1h/1.5h/2h

5. Cable length: 12m (39.37ft)

6. Maximum cleaning area: 60m² (for 12m cable in rectangle pool)

7. Filtering capacity: 20m³/h

8. Filter density: 180/600µm (600µm for the beginning of season)

9. Water temperature of use(for cleaner): 10°C - 35°C / 50°F - 95°F

10. Creeping speed: 20m/min

11. IP Grade：Cleaner-IPX8 Power supply unit-IPX5

12. Working environment temperature(for power unit): 10°C - 40°C / 50°F - 104°F

13. Maximum pool depth: 2m

6

14. Climb slope: Maximum25°

Ⅳ. Cleaner Structure

Assembly the cleaner according to above structure

Top Cover

Filter Tray

Chassis

7

Ⅴ. Operation Instruction

5.1 Cable connection

5.1.1 Plug the cable line into the socket on the power supply unit (note: make sure to plug it in

the correct direction and position), and fasten the nuts on both sides of the plug.

5.1.1 Connect the plug with power

Operating panel

Please plug or unplug the

cable by holding this

position

2

1 3