Page 1
USER MANUAL
Motorcycle Operating Manual Model:WY250T-3
PREFACE
Thanks for your purchasing the motorcycle WY250T-3, and sincerely
welcome you to be our motorcycle user. To enjoy a more safe and
pleasurable driving, at first please familiarity with the manual must
carry on before driving. Your personal safety depends not only the
vigilance and familiar operation skills, but also relates to whether you
are familiar with the mechanical performance. Before driving, check-up
and periodical maintenance are basic requirement. If maintenance and
repair needed, go to our service center for help. If you know the
mechanic knowledge and have the tools, the dealer can offer you help
with the maintenance and repair, like providing the parts catalogue and
the spare parts.
This manual explains in detail the correct operation and maintenance,
together with the expectation for your long-time use. Modifications in
specification could cause the discrepancy with some figures and content
in the manual, we feel sorry for that and hold the final right of
interpretation.
Have a good enjoyment and thanks again for your purchasing.
Page 2
The important points to attention
Ÿ The driver and passenger
This motorcycle was limited to one driver and one passenger (except children younger than 12 years old).
Never exceed the Max load capacity of motorcycle.
Ÿ For the safety, avoid driving the motorcycle in atrocious weather or cold weather (under -12 ℃).
Ÿ For the road condition
This kinds of motorcycle can only drive on the highroad.
The caution banners about the safety or environment protection stick to the sundries box cover, the rear
carrier, and fuel tank cap. (Being visible before or during driving)
• Please carefully read the user manual
You must attention to the warning sentence or paragraph.
WARNING：
Not following the operation instruction in this manual may cause great damage to you.
ATTENTION：
Not following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent parts, even when transfer the vehicle to a new owner, transfer the
manual at the same time.
LIST
Ⅰ.Motorcycle safe drive
Rules for safe drive …………………………1
Payload………………………………………1
Ⅱ.The tool set………………………………2
Ⅲ.Main technique parameter……………3
Ⅳ.The parts&subassemblies and manual
Parts&subassemblies…………………………5
Meter and indicator …………………………7
Ignition switch………………………………7
Fuel meter……………………………………8
Water temperature meter ……………………8
Headlamp switch ……………………………8
Starting switch ………………………………8
Main beam switch……………………………9
Turning light switch…………………………9
Horn switch…………………………………9
Steering handle lock…………………………9
Seat lock……………………………………10
Ⅴ. operation instruction
Checking before driving……………………11
Engine starting………………………………14
Driving motorcycle…………………………15
Driving operation…………………………16
Braking operation…………………………16
Engine power off operation…………………17
Stopping motorcycle ………………………17
Ⅵ.Service and maintenance
Maintenance periodic form…………………18
simple trouble solution ……………………20
Cleaning air filter …………………………22
Battery maintenance ………………………22
Adjusting idling speed ……………………23
Replacing engine oil and cleaning strainer…24
Replacing gearbox oil………………………25
Spark plug …………………………………26
Replaceing fuse ……………………………26
Radiator maintenance………………………27
Ⅶ.Vehicle identification …………………28
Ⅷ.Circuit…………………………………29
Ⅸ.Vehicle storage…………………………30
Ⅹ.Emission Control System
Warranty Statement………………………32
Page 3
- 1 -
Ⅰ. Motorcycle safe drive
Rules for safe drive
1. The motorcycle happen the many accident, all reasons are that the car drivers didn’t
look at the motorcycle drivers. So the motorcycle drivers must:
l Put up the coat in bright color
l Avoid to the driving at night .you must drive on guard and carefully to the strong
light.
2. Particular care should be exercised at the level crossing of roads, entrance and exit of
parking lot or on the automobile lane.
3. Don’t speeding, because the speeding usually to happen an accident.
4. You must get to the driving license and familiar with motorcycle. Never lend
motorcycle to the man without driving license or unfamiliar with motorcycle.
5. Avoid to driving the road with accidental, easily result in the operation without used or
the parts was broken.
6. You must check up the motorcycle before driving.(Look at the Page10).
7. During drive, grasp the left hand bar by the left hand and the throttle twist grip by the
right hand with feet on the footrests.
8. Don’t drive too close the other vehicles. Never contend for lane, and strictly observe
the local traffic rules.
Payload
warning:
The light goods can only put in the rear shelf or other deposited place.
- 2 -
The goods payload not heavier than table 1:
Table 1
Deposited Weight (kg)
Rear shelf 5
l The motorcycle max payload is 150kg,including the weight with the driver, the
passenger, the goods.
l If the motorcycle is over loading, it can affect the stability and operation of the
motorcycle.
l The goods on the motorcycle, must tie it.
The rear shelf not seats the children.
Ⅱ.The tool set
The tools bag(Pig1)in the boot of seat, Using for the urgent accident when
driving, it including the something of the following：
8×10mm spanner 12×14mm spanner
Screw drive Hexagon spanner
Wrench bar 18.5×17mm wrench spanner
Fig 1
Page 4
- 3 -
Ⅲ. Main technique parameter
Table 2
Item
Data
Item Data
L×W×H mm
2015×680×1210
Front
Tyre
130/160-13
Wheelbase
1350 Rear Tyre 110/180-10
Ground Clearance
mm 101 Air Pressure of Fr tyre 200 kPa
Dry weight kg 160kg Air Pressure of Rr tyre
250 kPa
Max Load kg 150kg Transmission system
CVT
Turning angle of steering
handle
≤48°
Ratio
5.12~15.05
Brake base mm
≤7(30km/h)
Engine Type
169MM
Single Cylinder、 4 stroke、
water-cooled
Max Speed km/h
≥100km/h Bore×stroke mm 69×66.8
Consumption L/100km
≤3.1L/100km
Displacement ml 249.8
Climb ability º ≥18
Clutch
automatically centrifugal
Light vertical angle -1.3% Fuel tank L 7
Starting system Electric Battery 12V 9Ah
- 4 -
Table 2
Item specification
Item Specification
Lubricative System Press & splash Ignition System CDI
Rated Power
10.5kW/6500（r/min）
Fuse 15 A
Max Torque
17.6N.m/5000（r/min）
Front light
12V 35W/35W×2
Compression ratio 10.0 1∶ Tail/stop light 12V P21/5W
Spark Plug Model
DPR7EA(NGK)、D7RTC 或 DPR6EA
License light 12V 5W
Spark plug gap
0.6～0.7 mm
Turning light
12V 10W×4
Gap of valve
0.1（cold）
Fuel RQ90 above
Idling speed (1500±150)r/min Gearbox oil SAE 80W/90
Engine oil SF SAE 10W/40
capacity of gea
r
box
0.18L
C
apacity of engine
oil
1.1L
Page 5
- 5 -
四、The parts&subassemblies and manual
The parts&subassemblies(fig2 fig3)
Meter and indicator
Fig 2
Battery
Main Stand
Seat Box
Fr Brake Lever
Ignition Switch
VIN Number
Nameplate
- 6 -
Dashed（……）Indicate the not see parts directly。
Meter and indicator （ Fig4）
Fig3
Fuel tank
Side stand
Air Filter
Seat Lock
Rear Brake bar
Handhold
Engine Number
Page 6
- 7 -
⑴Speedo meter
⑵Odometer
⑶main beam indicator
⑷Left Turning signal light
⑸Right Turning signal light
⑹Water temperature meter
⑺Fuel meter
(8)Time meter
(9)Parking light
Ignition switch（Fig5）
(1) On ( )-when the switch turn to this position,
Start engine and do not pull out the key.
1
⑵(2) Off ( ) When the switch turn to this position,
Start engine power off and take out the key. 2
⑶Lock ( ) When the switch turns to lock position ( ),
Take out the key .do not do any turning operation 3
And do not start engine and light.
Notice :If the engine is idling speed for a long time in the hot climate,
It will appear too hot. phenomenon Must close engine.
FIG4
FIG 5
6 8 9
- 8 -
FUEL METER（FIG6）
• Fuel meter (7) show the approx
remainder of flue. When the hand
point to (F), it indicates Full tank of 7.0L.
• When the hand at red section it
indicates the remainder of flue is 1.8L.
WATER TEMPERATURE METER（FIG7）
Water Meter6 show the approx temperature. When the hand
point to H, it indicates the water is hot, you should check the
Water Crank, Water tube, liquid cooled and the fan is okay.
Note: when the water is still hot, please not open it. In case
the water injury you.
Headlamp Switch (1)（FIG8）
The light switch: three position“ ” 、“ ” and“•”
：When it on the position, the front head light, tail light, position light and meter light turn on.
：When it on the position, tail light, position light and meter light turn on.
FIG6
FIG7
Page 7
- 9 -
•： When it on the position, the front head light, tail light,
position lighted instrument turn off.
Starting Switch（2）（ FIG8）
Press this button to start engine（P16）
Main beam switch（1）（ fig9）
Press“ ”button，is high beam；Press“ ”button is low beam。
Turning signal light switch (2)（fig9）
When the switches on ( ) ,the left turning signal light turn on.
When the switch on ( ), the right turning signal light turn on,
Press it down the light turn off.
Horn switch ( 3)（FIG9）
Press this button, the horn makes sound.
Steering handle lock（FIG10、FIG11）
Steering lock: turn handle left to end, presses down ignition key1 to ( ), the steering
device are locked Do the above opposite it opened.
FIG8
1
3
2
FIG9
1
2
- 10 -
Multi-purpose lock (Fig 12)
Put the key into multi-purpose lock hole
and then clock-wise open the lock.
Press down the multi-purpose until it
make sound of locked, then push the back
of multi-purpose to confirm it has been
locked and take out the key.
FIG10
1
FIG11
Page 8
- 11 -
Ⅴ. Operation Instruction
Checking before driving:
Checking before riding, For safety and prevent trouble or accident,
pre-check up is necessary.
GASOLINE
When the pointer or fuel meter is close to red section, replenish fuel.
Gasoline tank container: 7L
Clock –wise to open the tank cover 2. (Fig 13)
Suggestion gasoline: octane number is 90
Do not replenish fuel together with tidy or water
NOTICE:
If check fuel volume or replace fuel soon after stop, Beware of burning.
Keep gasoline level under away from the height panel of flue tank while replenishing.
If gasoline level is too high, it is easy to leak out.
If swallow the oil careless, see the doctor at once.
Checking the cooling system:
Before driving, please check the water case. Water tube,
liquid cooled and fan are working normal.
Fig 12
Fig 13
- 12 -
Checking engine oil
Checking engine oil level（FIG14、FIG15）
1.Keep the motor steady in the plane screw up
the oil dip rod and clean it, then reinsert and
inspect oil.
2.If the oil level reach to down limit sign (2),
replenish the standard oil to upper limit sign
(3), then put the oil level into, cover the lid, to
check it whether seeking.
Suggestion the engine oil
SAE-10W/40
The free path of rear brake handle（ Fig16、Fig17）
Measure the distance of rear brake pedal before detent
function .the free path should between 10-20mm, take
the tail of brake handle as standard.
Adjust nut (A): increase the distance of free path
(B): reduce the distance of free path
The axle pin2 should touch closely with nut (1) groove after adjust.
1
Fig14
3
2
Fig15
Page 9
- 13 -
Tire
Check the tire pressure regularly and adjust.
Check before the tire cooled
Check if there any metal trash or
gravel in the groove of tires
WARNING:
If the tire pressure dose not accord with the standard, it will properly cause the traffic accident.
• It is dangerous that use the worn tire, It will have effect to friction between tire and rode.
Maybe make difficult from drive or accident.
Ÿ
1 2
FIG17
FIG16
(10～20)mm
- 14 -
Starting engine (Fig 18)
Put the key into ignition switch and turn to ON
Electric starter: press start button (1) to
start engine, DO not use the starter more
than 5 seconds each time.
NOTICE:
Electric starting is only in the condition of grasping the brake handle.
Electric starting not succeed, if starting again with it, we must stop for 30 seconds, If still can’t
start, Please use kick-start.
Engine kick-start :open ignition switch and add gasoline slowly, step kick-starter pedal down
quickly with strength to start engine.
Notice: After using kick-starter pedal, pull it back to original position. Otherwise have
effect to safety ride, and bad to engine.
Had better not open ignition switch when scooter has
not use for a long time, and first step kick starter for some
times. Make flue into carburetor and then into cylinder,
and open ignition switch, Start engine, it is easy to start
engine like this.
If cold start warm up engine for 2-3 minutes.
1
1
Fig 18
Fig 19
Page 10
- 15 -
Driving motorcycle:
WARNING:
Wear the trousers to avoid touching with exhaust pipe and was burnt.
The entire device must be installed according to requirement of the traffic rule.
Take the license to riding.
NOTICE:
Control the speed and load during 1000kmof running in period.
Load should be within 100kg(including driver)
If take more weight and speed will reduce life of engine, Change the crankcase oil after
300km (Page 25) to a new motorcycle.
Speed according to (Table 3)
Table 3
Log（km） 0～200 200～500 500～1000
Speed(km/h) ≤30 ≤45 ≤55
- 16 -
Driving operation
Release rear brake level, add gasoline slowly with throttle grip, then motorcycle will move
forward smoothly.
NOTICE:
Do not add much gasoline suddenly with throttle grip to prevent motorcycle rush out. Maybe
lose control.
Before drive, must take the stand.
Braking operation:
1.Control throttle grip
If want to reduce speed, Must control the throttle grip, at that time use the two-brake system,
this point is very important.
Notice: if the drive will be done in this situation, for example: damp or loosely roads,
raining .no matter brake, add speed or turn must take care.
2.operate front and rear brake.
Notice: Must totally close the flue when drive in a descent, and use two-brake system for
reduce speed. Don’t use brake continuously, other wise it will reduce the effect of brake
because of too hot.
Warning: Don’t use single brake when drive with high speed, special crooked and slippery
road. Must use two-brake system for avoiding accident.
Page 11
- 17 -
Engine power off operation (Fig 20, Fig 21)
Close oil: revolve to the lowest place according to picture. (Normal situation is loose the throttle
grip, and the engine is idling speed)
• Put the key to “OFF
Stopping operation:
When the motorcycle stop, put the key to “ ” position .put down stand and lock handle.
(Page 9)
Alarm points:
1 Locking the handle and do not left key in the switch
2 Put the motor into the garage
3 Use the excellent guard against theft device
1
FIG 20
FIG21
- 18 -
Ⅵ.Maintenance and service
Maintenance periodic form
The maintenance is important to motorcycle, If drive with high speed in bad situation for a
long time, must add the times of maintenance, If motorcycle have a big repaired or a
accident, Must take it to check for mainly spare parts. For example: frame, indicator parts
and so on. Repair or change the worn parts. Make sure safety.
Notice: Don’t change motorcycle make sure it’s safety, Must use good quality spare parts if
replace spare parts .if use bad quality spare parts, it will influence the safety of motorcycle.
Warning: Must close engine when make maintenance .it make sure the repairer’s safety.
And put down the stand on the smooth ground.
Notice: Must make a good maintenance if the motorcycle don’t use over a month, or don’t
use in all the winter. Make flue, tire and battery avoiding corrode.
Maintenance periodic table (table 4):
Check before time based maintenance (Page 10)
I: check and adjust when necessary
C: clean
R: change
Page 12
- 19 -
table 4
speedometer（x1000km）
1 4 8 12
Cycle
Item
Every month
6 12 18
Ref page
﹡
Fuel pipe
I I I I ﹡
Throttle grip
I I I I 18
﹡
Core of the air filter
Note1 C/1000km, if need: R
25
﹡
Spark plug
C/2000km,If need: R
29
﹡
Valve
I I I I
﹡
Engine oil
（
300km
）
R
R
(
300
km)
R
27
﹡
Engine oil filter
When change oil If need: D
27 ﹡
carburetor
I I I I 26
﹡
belt
Per1000km I If need: R
gearbox oil Note3
(300km）R
I 28
Brake syetem
I I I I 14
Brake switch
I I I
﹡
Headlamp
I I I
﹡
Suspension
I I I
﹡
nuts\bolts
tighten
Note2
I I
﹡
Wheel & tire
I I I 13 ﹡
Turning bearing
I I
*If you have all of tool and maintenance document, you are a mechanic person, or else must let
special person maintenance and repair.
- 20 -
**For safety, we claim all of items have done by mechanic person.
Note: 1.if this area is very damp or have a lot of dirty .you had better make a short time for
maintenance, when it take more oil quantity or not strength, it must change.
2.if it was used every day, must make maintenance.
3. according to season to change in a cold area.
Simple trouble solution (Table 5)
Trouble
phenomenon
Trouble reason Solution
Spark plug wear Change
Ignition wire wear Change
CDI wear Change
Ignition switch wear Change
Spark plug no
spark
Ignition Come off or become flexible Connect well or firm and tight
Spark plug gap too small or big Adjust
Spark plug pole burn Change
The spark plug accumulates carbons
Clear out
No fuel Replenish
Oil mouth stop up Dredge
The spark is
weak
Fuel tank pressed the switch to
Clean
Air filter stop up Clear
Take in system leak Check and clear out
Spark plug seat leak Screw up spark
THE ENGINE
CAN NOT
START
The cylinder
compresses
strength low
Cylinder cover leak Change spacer
Page 13
- 21 -
Table 5
Trouble
Trouble reason Solution
The octane value of the fuel is too low
Change fuel
Oil path stop up
Clean oil path
Ignition time is too early or too late
Check wire and change CDI
Spark too weak or flameout
Check ignition and clear out
Mixed air too dense or race
Clean adjust carburetor
Engine leak
Check and clear out
Muffler stop up
Dredge
Belt wear
Change
The vehicle is
unable to accelerate
performance badly
The automatic clutch roller wearing
Change
Exceed clutch worn
Change
Start the relay wear
Change
The electricity is
started and does not
work
Lack of Electric consumption
Discharge
Turning axletree gap too wide
Adjust
Lack of tire pressure
Pump
Riding unsteady
Front rear shaft flexible
Screw up nut
The brake shoe one is worn and torn to limit
Change
Apply brake to enclose wear
Change
Apply the brake and
does not work
The guy cable is worn to apply the brake
Change
- 22 -
Cleaning air filter(Fig 22):
1 Take out rear protecting bar left protecting bar
2 Take apart air filter cover and screw up bolt.
3 Take out filter element
4 Compress air or use dry brush to clean filter element.
Do the above opposite to reinstall the air filter.
NOTICE:
Do not use gasoline or low burning
point solvent to clean paper filter element.
Maintenance battery(Fig 23)
• It is Adopted the airtight battery (don’t add water).
Notice: Do not take apart the airtight battery upper cover
• If the motorcycle have not been used for long time.
Taking off the battery and putting it into a dry and place.
• The head of battery was corroded, please take
it off and clean. (Can use boil water)
NOTICE: turn off the ignition switch, take apart negative
pole ○
-
first, but install positive pole ○
+
when you are
installing.
Fig2
3 Fig2
2
Page 14
- 23 -
Adjusting idling speed(Fig 24, Fig 25)
The carburetor is in the best situation before
sold, if the carburetor is still influence riding
Please adjust it under the instruction of professional man.
Warm up few minutes before start。
Idle to adjust screw (1) is it is it improve idle
speed slightly to enter to fasten, is it is it
withdraw it than screw slowly after stocking to
fasten to mix and then rapidly, to stabilizing the
position at most, then withdraw slowly, get and
stabilize the position the most low.
After adjust idle, then adjust accelerograph handle to
free path for 2-4mm,then use adjustor (2) to adjust,
screw down nuts, and then screw up it after adjust.
Adjusting the good idle speed, when should be able to
suddenly strengthen the throttle, the rotational speed of the
engine should be excessively steady, no flash back and
can't go out, stop working or arrange organ not to blow out at being last throttle.
1
2 3
Fig2
4 Fig25
- 24 -
Replacing engine oil and cleaning strainer (Fig 26, Fig 27)
Replacing engine oil（Fig26）
Suggestion engine oil : SAE 15W/40
• Replacing the engine oil before engine cold, and under
the condition of steady of motor.
Cleaning the strainer. （Fig27）
• Take out oil hole cover and oil filter (1) then take strainer
(2) and spring (3)!
• Using liquor clean the strainer.
• Install oil filter then take strainer and spring!
• Replenish the standard engine oil to upper limit line of
the oil hole cover.
• Install the cover of hole and liter.
• Start engine and keep for few minute then flameout.
• Measure the lever of engine oil again, makes sure it is not
leak.
Fig26 Fig2
7
Page 15
- 25 -
Replacing gearbox oil (Fig 28)
Suggestion engine oil : SAE 80W/90
Oil container
Resolving capacity：0.18L
Changing capacity ：0.16L
Take apart the immiting bolt (2), and the spilling bolt (1).
NOTICE: THE ENGINE MUST BE WARMER
WHEN SPILLING, AND THE VEHCILE MUST
BE STEADY BY MAIN STAND!
• Reinstall the spilling bolt after clean. And screw up.
• Inject 100ml to engine through immit bolt
• Using the injector to immit the oil to the bolt, till full.
• Install immit bolt and screw up.
Fig28
- 26 -
Spark plug(Fig 29)
The specification of spark plug: DPR7EA ,DPR6EA (NGK)or D7RTC
• Take apart the spark plug; Take it of with special tool.
• Examine if there is dirty on poles and the porcelain
head in center .If it has corroded, must change it .It is
the best way to clean with the liquor of spark plug
Use wire brush if no cleaner
• Normally the gap between side electrode (1) and
Center electrode (2) is 0.6-0.7.
• Don’t use other spare plug.
Replacing fuse
The specified electric current of the total fuse is 15 A
If the connection is not good, the fuse will overheat and breakdown.
Do not use any fuse whose specification is different from assigned. It is the same
Main reason for wiring burning.
NOTICE: Do not use brass wires to replace the recommended.
(0.6～0.7)mm
1
2
Fig2
9
Page 16
- 27 -
Radiator Maintenance
Suggestion Cooled liquid Type: anti-freeze liquid
It’s only using no rust no freeze liquid for this engine。
Inspecting
Open the bolt, take the cover off, you can see the liquid lever is
staying1/5，if less than1/5，please immit it.
Immiting the Cooled liquid
Ÿ Open the gas of the radiator 1. if the cooled liquid is not full,
please keep it full. Then cover it.
Ÿ if you want to add more cooled liquid, starter the engine
liquid rising 80℃，waiting for 5minuts thenopen the cover
again1，till the liquid full, close the cover.
Ÿ Following the above number, you can add the liquid
for three times.
Ÿ Or you can open the cover 2 to immit the liquid after the
engine is cooled.
Warning：
When the engine is high temperature, not open the cover, in
case the liquid burst out to injury the body.
1
Fig 30
2
Fig31
- 28 -
Ⅶ.Vehicle identification
Vehicle model, VIN and engine number of the motorcycle（Fig32）
When the motorcyle are registered or getting the license from the transport department, the
owner should be send the VIN number and engine number。The maintain people change
the parts, need the numbers too.。
The products brand should be added at the right side plate of the main stand（see page 5）
Fig32
Page 17
- 29 -
Ⅷ.Circuit Diagram
- 30 -
Ⅸ.Vehicle Storage
Storage
For the motorcycle not to be used for a long period of time, for example, in wintertime, some
steps should be taken to prevent malfunction of and damage to its components, which might be
caused by long storage. Besides, before the long storage, proper maintenance has to be carried
out for fear that it might be forgotten when vehicle is put back into use after storage.
1. Change engine oil and oil filter.
2. Drain off fuel from the fuel tank and carburetor, spray atomized anti-rust oil onto the inside
wall of the tank and then close the tank.
Warning:
Gasoline is inflammable and may cause fire and even explosion under certain conditions.
Therefore, do not smoke, make fire or have any fire left behind on draining off fuel.
3. Take out the spark plug, pour about 15~20ml clean engine oil into the cylinder, step down
the kick lever repetitively for several times so as to have machine oil distributed all over the
engine and finally fit the spark back on.
Attention:
The ignition switch must be set to ”OFF” position before stepping down the kick lever.
To protect the ignition system from damage, the spark plug should be inserted in its cap and
earthed.
4. Wash the motor, wipe it dry and apply an even coat of wax to the painted surface. Chromate
treatment can prevent the surfaces from rusting.
5. Inflate the tires as required and pad the vehicle up by wooden blocks with the two wheels
clearance of the ground.
6. Put the vehicle in a shady and cool place free from humidity and direct sunshine and cover
it properly (but not with plastic or other painted materials).
Page 18
- 31 -
Reuse motorcycle.
Clean the motorcycle, if the storage time beyond 4 months, Must change gasoline.
Must charging if need, and then install battery.
Must check all of terms before drive (Page 10), for the safety must try the motorcycle with
lower speed for some time in a not busy rode.
- 32 -
Ⅹ.Emission Control System Warranty Statement
Wangye USA Co., LLC is pleased to explain the emission control system warranty on
Highway Motorcycle. New Highway Motorcycle must be designed, built and equipped to
regulations and standards of the United States Environmental Protection Agency and the
California Air Resource Board and free from defects in material and workmanship that may
keep it from these requirements in the all applicable regulations.
Wangye USA Co., LLC must warrant the emission control system on the highway motorcycle
for 5 years or 18,000 km, whichever comes first, provided that there has been no abuse, neglect
or improper maintenance of highway motorcycle.
1. Period of Warranty
The period of warranty shall be one year on delivery, during this period of warranty:
(i). Any part defective by reason of the manufacturer’s faulty workmanship or material will be
replaced or repaired free of charge;
(ii). Any repairs or adjustments made necessary by reason of the manufacturer’s faulty
workmanship or material will be performed free of charge.
Emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, catalytic converter and engine computer, if it is equipped. Also included may
be hoses, belts, connectors and other emission-related assemblies.
2. Responsibilities of Customer
To obtain repairs under warranty, the customer must:
(i). Ensure that the motorcycle is properly operated, maintained and stored as specified in the
Page 19
- 33 -
Owner’s Manual;
(ii). Give notice to dealer approved by Wangye USA Co., LLC or other qualified service facility
of any and all apparent defects immediately upon discovery, and make the entire
motorcycle available at the time for inspection and repair at the dealer’s place of business;
(iii). Provide proof of warranty coverage to dealer;
(iv). Authorize the dealer to tear down the motorcycle for diagnostic evaluation should it be
required.
All warranty repairs must be done by the dealer and final approval of any repairs rests with
Wangye USA Co., LLC. All parts replaced become the property of Wangye USA Co., LLC.
3. Exclusion
This warranty does not cover the repair or damage resulting from abuse or neglect of the
motorcycle. Examples of abuse and neglect include, but are not limited to:
(i). Racing and competition;
(ii). Use of lubricants, oils and fuel/oil mixture other than those recommender in the Owner’s
Manual, improperly installed accessories and use of parts or accessories that are not
equivalent in design and quality to genuine Wangye parts;
(iii). Damage as a result of accidents, collisions, contact with foreign materials, impact,
submersion or use of the motorcycle after discovery of a defect;
(iv). Appearance-related damages of body parts. Examples of such damages include but are not
limited to: scratches, dents, fading, flaking and peeling;
(v). Motorcycle which has been modified in any way from the standard specifications shown in
the Owner’s Manual, for example, the odometer has been altered;
(vi). Normal wear and tear, corrosion and routine maintenance, such as the recommended
service inspections;
(vii). Pre-delivery inspection and assembly;
- 34 -
(viii). Damage from theft, fire, vandalism, explosion, water or acts of God.
4. Restriction
This warranty is in addition to, and not a modification of, any legal warranty required by the
laws of any state of US.
Subject to any applicable sales or consumer legislation, the above warranty is in lieu of any
warranty or representation, express or implied, including any warranty of performance,
merchantability or fitness for a particular purpose on the part of Wangye USA, and any other
obligation or liability on behalf of Wangye USA, and the above warranty constitutes your sole
remedy and the full liability of Wangye USA. In no event shall Wangye USA be liable for
special, incidental or consequential damages howsoever caused, whether by negligence or
otherwise resulting directly or indirectly from the use of the Motorcycle, or the Motorcycle’s
having replacement parts or the unavailability of replacement parts. Wangye USA does not
assume or authorize any person to create or assume for Wangye USA any obligation or liability
in connection with the Motorcycle or any part thereof distributed by Wangye USA.
5. Contact
For any questions regarding emission control system warranty, please contact as following:
Company Name: Wangye USA Co., LLC
Address: 1170 Corporate Dr. West Ste. 204, Arlington, TX 76006
Tel: 817-640-1108 ext 219
Fax: 817-649-5006
Loading...