Walkdesk WTD200, WTB100 Owner's Manual
1
WALKDESK WTD200
OWNER’S MANUAL
Stadsheide 3 | 3500 Hasselt | Belgium | T +32 11 76 12 70
info@bodysolid-europe.com | www.bodysolid-europe.com
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW ELLIPTICAL
1
ATTENTION
This treadmill is intended for residential use only and is warranted for this application.
Any other application voids this warranty in its entirety.
TABLE OF CONTENTS
Important Safety Instructions 2
Important Electrical Instructions 3
Grounding Instructions 3
Important Operation Instructions 4
Desk Assembly Instructions 5
Folding/Transport Instructions 10
Console Operation 11
General Maintenance 15
Service Checklist – Diagnosis guide 18
Exploded View Diagram/Parts List 19
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
DANGER - To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to
cleaning and/or service work.
WARNING
- To reduce the risk of burns, fire, electric shock, or injury to persons, install the treadmill on
a flat level surface with access to a 230~volt, 10-amp grounded outlet with only the treadmill plugged into
the circuit.
DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH ONLY ONE
OUTLET ON THE END.
The treadmill should be the only appliance in the circuit in which it is connected.
DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER
ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard may result
along with computer malfunctions. See Grounding Instructions.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet
and treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance between the
rear of the treadmill and any fixed object.
Keep children away from the treadmill. There are obvious pinch points and other caution areas
that can cause harm.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug.
If the treadmill is not working properly, call your dealer.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the off position, then remove the plug from the outlet.
Do not attempt to use your treadmill for any purpose other than for the purpose it is intended.
The hand pulse sensors are not medical devices. Their purpose is to provide you with an
approximate measurement in relation to your target heart rate. Use of a chest transmitter strap
is a much more accurate method of heart rate analysis. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are intended
only as exercise aids in determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
SAVE THESE INSTRUCTIONS - THINK SAFETY
3
IMPORTANT ELECTRICAL INSTRUCTIONS
WARNING
!
NEVER
use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any appliance
with a large motor, the GFCI will trip often. Route the power cord away from any moving part of the
treadmill including the elevation mechanism and transport wheels.
NEVER
remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)
or more, the performance of your treadmill may be affected. Such conditions are not covered under your
warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for
proper testing.
NEVER
expose this treadmill to rain or moisture. This product is
NOT
designed for use outdoors, near a
pool or spa, or in any other high humidity environment. The operating temperature specification is 40 to
120 degrees Fahrenheit, and humidity is 95% non-condensing (no water drops forming on surfaces).
Circuit Breakers:
Some circuit breakers used in homes are not rated for high inrush currents that can
occur when a treadmill is first turned on or even during use. If your treadmill is tripping the house circuit
breaker (even though it is the proper current rating) but the circuit breaker on the treadmill itself does not
trip, you will need to replace the home breaker with a high inrush type. This is not a warranty defect.
This is a condition we as a manufacture have no ability to control. This part is available through most
electrical supply stores. Examples: Grainger part # 1D237, or available online at
www.squared.com
part # QO120HM.
GROUNDING INSTRUCTIONS
This product must be grounded. If the treadmill should malfunction or breakdown, grounding provides
a path of least resistance for electric current, reducing the risk of electric shock. This product is equipped
with a cord having an equipment-grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether
the product is properly grounded. Do not modify the plug provided with the product if it will not
fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 230~volt circuit, and has a grounding plug that looks like the plug
illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to
connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly grounded outlet, (shown below) can be installed
by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be
connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is
used, it must be held in place by a metal screw.
4
IMPORTANT OPERATION INSTRUCTIONS
NEVER
operate this treadmill without reading and completely understanding the results of any
operational change you request from the computer.
Understand that changes in speed and incline do not occur immediately. Set your desired work
level on the computer console and release the adjustment key. The computer will obey the command
gradually.
NEVER
use your treadmill during an electrical storm. Surges may occur in your household power
supply that could damage treadmill components. Unplug the treadmill during an electrical storm
as a precaution.
Use caution while participating in other activities while walking on your treadmill; such as watching
television, reading, etc. These distractions may cause you to lose balance which may result
in serious injury.
Do not use excessive pressure on console control keys. They are precision set to function properly with
little finger pressure.
SAFETY TETHER CORD
A safety tether cord is provided with this unit. It is a simple magnetic design that should be used at all
times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the round metal portion of the console control head.
Your treadmill will not start and operate without this. Removing the magnet also secures the treadmill
from unauthorized use.
2. Fasten the plastic clip onto your clothing securely to assure good holding power.
Note: The magnet has strong enough power to minimize accidental, unexpected stopping.
The clip should be attached securely to make certain it does not come off. Be familiar with its function
and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime
the magnet is pulled off the console. Use the Stop / Pause switch in normal operation.
5
DESK ASSEMBLY INSTRUCTIONS
!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS.
PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!!
Serious injury could occur if this folding treadmill is not unpacked properly.
There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding
accidentally during shipping. If this strap is not removed properly the treadmill could spring open
unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed.
To ensure your personal safety during removal of the shipping strap please make sure the treadmill is
positioned flat on the ground, in the orientation it would be in if you were using the treadmill. Do not turn
the treadmill up on its side while removing the shipping strap. This could cause the treadmill’s folding
mechanism to spring open. If the end of the Velcro strap (that you need to grab to remove it) happens to be
under the treadmill deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to
the strap end.
Cut the banding straps with a short box cutter (razor knife); separate the carton from the one underneath it
by prying up on the staples (if applicable). Pull the carton over the treadmill parts and locate the hardware
pack. The hardware pack is separated into five sections; one section containing tools and four sections
labeled steps 1-4 which contain the hardware needed for assembly of each step. The assembly steps
below are numbered one through four and correspond to the hardware in the numbered sections of the
hardware pack. Remove only the hardware for the step you are currently assembling to avoid confusion
and mix ups.
Then remove the treadmill from the carton and lay it on a level surface.
DESK ASSEMBLY TOOLS
#142. M5 Allen Wrench
#141. L Allen Wrench
#139. Phillips Head Screw Driver
#140. Wrench
6
Connect Fixed Upright Assembly(113) with Frame Base Tube(L.R)(116) and use L Allen Wrench
(141) to tighten 16 pcs of 3/8” × UNC16 × 1/2”_Button Head Socket Bolts (135).
HARDWARE
#135. 3/8” × UNC16 × 1/2”
Button Head Socket Bolt
(16 pcs)
1
Loading...