Wali M001LP User Manual
INSTALLATION MANUAL
Single Mount With Laptop Tray
M001LP
Supplied Parts List
www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)
RATED
(10kg/22lbs)x2
75x75\100x100
Laptop : 17” Max
Monitor: 27” Max
！
WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
TIPOVER WARNING
！
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Pole
a (x1)
Grommet Base Plate
m (x1)
Option A : Clamp Installation
1
1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and
tighten with Allen Key 3mm o .
C-Clamp
b (x1)
Wire Clip
n1 (x2)
a c
o
C-Clamp Brace
c (x1)
Wire Clip
n2 (x3)
a
Swivel Arms
d (x1)
Allen Key
o (x1)
VESA Plate
Wrench
p (x1)
e (x2)
M5x14 Bolt
M4x12 Bolt
q (x8)
f (x3)
M4x30 Bolt
r (x8)
M8x12 Bolt
g (x2)
M4 Spacer
s (x8)
Nut
h (x2)
Laptop Tray
t (x1)
M10 Bolt
i (x1)
M4x10 Bolt
u (x4)
Support Plate
j (x1)
M4 Nut
v (x4)
M10 Washer
k (x1)
Washer
w (x4)
Spring Washer
l (x1)
Anti-skid Pad
x (x4)
Option B : Grommet Base Installation
f
2. Select the preferred height according to your desk thickness. Connect C-Clamp b to C-Clamp
c
Brace c using M8x12 Bolt g and tighten with Allen Key 5mm o . Rotate the hand knob
clockwise to fasten for stability.
g
o
c
b
1. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using
M5x14 Bolt and tighten with Allen Key 3mm .
a
f
m
o
a
g
b
o
c
f
o
Hand Knob
f
o
m
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before
installing the desk mount. Position the Pole a on the mounting surface and secure using the
Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using
the provided Wrench p .
j
p
k
a
l
i
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at the
marked position through the mounting surface. Position the Pole a on the mounting surface and
secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the
Bolt using the provided Wrench p .
j
p
k
a
l
i
Put the Wire Clip n1 and Swivel Arms d through the Pole a , adjust the preferred height
2
n1
and tighten using Allen Key 6mm o . Attach the Wire Clips n1 to the Swivel Arms d .
d
o
a
n2
d
j
a
j
k
l
i
Option A : Laptop Tray Installation
3
Using M4 X 10 Bolt u , M4 Nut v , and Washer to attach the VESA
e
Plate e to the laptop tray t and tighten with a screwdriver. Put the Anti-skid
x
Pad on the designated position on the tray. (Screwdriver not included)
x
x
u
u
vu w
t
w
e
e
p
t
t
d
a
j
ø 10mm
(ø ") 3/8
n1
n2
a
j
k
l
i
p
o
Option B : Monitor Mount Installation
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included)
Step 1
Select Monitor Screws
Step 2
Only one screw size fits your Monitor
M4x12
w
w
M4x30
Hand thread screws into the
threaded inserts on the back
of your Monitor to determine
which screw (M4x12 or M4x30)
to use.
Select Spacers ( if needed )
Step 3a
Flat Back Monitor
e
Step 3b
q
Curved or Recessed Back Monitor
s
r
v
v
Put the assembled laptop tray and TV/Monitor onto the Swivel Arms d . Tighten the VESA
4
Plate e with Nut h for stability.
e
e
h
h
d
d
n1
Guide the cable through the Wire Clips ( n1, n2 ) and store the Allen Keys o in the Wire Clip n1 .
5
Adjust the tilt angle using Allen Key 5mm n .
o
n2
o
o
n2
n1
e
n1
Manually swivel, tilt, and rotate the monitor laptop tray for the best viewing angle.
6
Notice: Please make sure the security nut is installed before you rotate the monitor.
h
For safety, please remove your laptop when making adjustments.
h
15°
15°
o
Laptop Tray Holder
Loading...