Waldorf RN8510GEC, RN8810GE, RN8610GE, RN8610GEC, RN8810GEC Operation Manual

Installation and Operation Manual

RN8510GE/GEC
RN8610GE/GEC
RN8810GE/GEC

Gas Ranges Electric
Static/Convection Oven

Date Purchased

Serial Number

Dealer

Service Provider

230562-11

RNL8510GE/GEC
RNL8610GE/GEC
RNL8810GE/GEC

For use in GB, IE & DK

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.

© Copyright Moffat Ltd. March 2010.

MANUFACTURED BY

Moffat Limited
PO Box 10001
Christchurch
New Zealand
Ph: [phone]
Fax: [phone]

WORLD-WIDE BRANCHES

UNITED KINGDOM

Blue Seal
67 Gravelly Business Park
Gravelly Park
Birmingham
West Midlands
B24 8TQ
Ph: [phone]
Fax: [phone]

UNITED STATES

Moffat Inc
3765 Champion Blvd
Winston-Salem
North Carolina 27115
Ph: [phone]
Fax: [phone]

CANADA

Serve Canada
22 Ashwarren Road
Downview
Ontario M3J1Z5

Toll Free:800 263 1455
Ph: [phone]
Fax: [phone]

[e-mail]
www.servecanada.com
www.moffat.com

NEW ZEALAND

Christchurch

Auckland
Moffat Limited Moffat Limited
PO Box 10-001 4 Waipuna Road
16 Osborne Street Mt Wellington
Christchurch Auckland
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

AUSTRALIA

Victoria

New South Wales
Moffat Pty Limited Moffat Pty Limited
740 Springvale Road 3/142 James Ruse Drive, Rose Hill
Mulgrave, Melbourne PO Box 913, Smithfield
Victoria 3171 Sydney, N.S.W. 2142
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

Western Australia

Queensland
Moffat Pty Limited Moffat Pty Limited
67 Howe Street 30 Prosperity Place
Osbourne Park Geebung, Brisbane
WA 6017 Queensland 4034
Ph: [phone] Ph: [phone]
Fax: [phone] Fax [phone]

1

Waldorf Gas Range Electric Static/Convection Ovens

RN(L)8510GE Gas Range Electric Static Oven Four Open Burner.
RN(L)8610GE Gas Range Electric Static Oven Six Open Burner.
RN(L)8810GE Gas Range Electric Static Oven Eight Open Burner.

RN(L)8510GEC Gas Range Electric Convection Oven Four Open Burner.
RN(L)8610GEC Gas Range Electric Convection Oven Six Open Burner.
RN(L)8810GEC Gas Range Electric Convection Oven Eight Open Burner.

Introduction .............................................................................................. 2

Specification .............................................................................................. 3

Model Numbers Covered in this Specification
General
Gas Supply Requirements
Gas Connection
Electrical Supply Requirements
Electrical Connection

Dimensions ................................................................................................ 6

Installation ................................................................................................ 9

Installation Requirements
Unpacking
Location
Clearances
Assembly
Fitting Rear Rollers
Gas Connection
Electrical Connection
Commissioning

Operation ................................................................................................. 14

Operation Guide
Description of Controls
Open Burners
Griddle
Oven

Cleaning and Maintenance ...................................................................... 18

General
After Each Use
Daily Cleaning
Weekly Cleaning
Periodic Maintenance

Fault Finding ............................................................................................ 22

Wiring Schematic..................................................................................... 24

Gas Conversion and Specifications..........................................................28

Conversion Procedure
Gas Specifications

Replacement Parts List............................................................................34

Contents

2

Introduction

We are confident that you will be delighted with your WALDORF GAS RANGES ELECTRICAL STATIC /
CONVECTION OVEN and it will become a most valued appliance in your commercial kitchen.

To ensure you receive the utmost benefit from your new Waldorf appliance, there are two important things
you can do.

Firstly:

Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.

Secondly:

If you are unsure of any aspect of the installation, instructions or performance of your appliance,
contact your WALDORF dealer promptly. In many cases a phone call could answer your question.

CE Only:

These instructions are only valid if the country code appears on the appliance. If the code does not
appear on the appliance, refer to the supplier of this appliance to obtain the technical instructions for
adapting the appliance to the conditions for use in that country.

WARNING:

I

MPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS APPLIANCE.

WARNING:

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS ARE TO BE POSTED IN A PROMINENT
LOCATION. THIS INFORMATION SHALL BE OBTAINED BY CONSULTING THE LOCAL GAS SUPPLIER.

WARNING:

G

REAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE EQUIPMENT SAFELY TO GUARD IT AGAINST RISK

OF FIRE.

• T

HE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.

• I

T IS RECOMMENDED THAT A REGULAR INSPECTION IS MADE BY A COMPETENT SERVICEMAN TO ENSURE

CORRECT AND SAFE OPERATION OF YOUR APPLIANCE IS MAINTAINED.

• DO NOT

STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

•

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

C

AUTION

:

This appliance is;

•

For professional use and is to be used by qualified persons only.

•

Only qualified service persons are to carry out installation, servicing and
gas conversion operations.

•

Components having adjustments protected (e.g. paint sealed) by the
manufacturer should not be adjusted by the user / operator.

•

DO NOT operate the appliance without the legs supplied fitted.

3

Specifications

Model Numbers Covered in this Specification

RN[1]8510GE [2] 4 Open Burners + Electric Static Oven.

RN[1]8513GE [2] 2 Open Burners + 300mm Griddle + Electric Static Oven.

RN[1]8610GE [2] 6 Open Burners + Electric Static Oven.

RN[1]8613GE [2] 4 Open Burners + 300mm Griddle + Electric Static Oven.

RN[1]8616GE [2] 2 Open Burners + 600mm Griddle + Electric Static Oven.

RN[1]8619GE 900 mm Griddle + Electric Static Oven.

RN[1]8810GE [2] 8 Open Burners + Electric Static Oven.

RN[1]8813GE [2] 6 Open Burners + 300mm Griddle + Electric Static Oven.

RN[1]8816GE [2] 4 Open Burners + 600mm Griddle + Electric Static Oven.

RN[1]8819GE [2] 2 Open Burners + 900mm Griddle + Electric Static Oven.

RN[1]8510GEC [2] 4 Open Burners + Electric Convection Oven.

RN[1]8513GEC [2] 2 Open Burners + 300mm Griddle + Electric Convection Oven.

RN[1]8610GEC [2] 6 Open Burners + Electric Convection Oven.

RN[1]8613GEC [2] 4 Open Burners + 300mm Griddle + Electric Convection Oven.

RN[1]8616GEC [2] 2 Open Burners + 600mm Griddle + Electric Convection Oven.

RN[1]8619GEC 900 mm Griddle + Electric Convection Oven.

RN[1]8810GEC [2] 8 Open Burners + Electric Convection Oven.

RN[1]8813GEC [2] 6 Open Burners + 300mm Griddle + Electric Convection Oven.

RN[1]8816GEC [2] 4 Open Burners + 600mm Griddle + Electric Convection Oven.

RN[1]8819GEC [2] 2 Open Burners + 900mm Griddle + Electric Convection Oven.

NOTE:

[1]: - Back Options;

- - Standard Models.
L - Low Back Models.

[2] - Open Burner Options;

F - With Flame Failure Protection.
PF - With Pilot and Flame Failure Protection.

General

A heavy duty, general purpose gas range created for compact modular kitchens. It has a high option
Cook Top / Griddle arrangement and is available on industrial adjustable feet or on robust rollers.

Open Burners are available in either 'PF' (Pilot and Flame Failure) or 'F' (Flame Failure Only) options.
Open Burner and Griddle options are fitted with individual flame failure for each open burner.
Griddles are fitted with pilot, flame failure and piezo ignition as standard. Easy clean stainless steel
external finish.

Easy clean stainless external finish.

4

Specifications

Gas Supply Requirements

- Non CE Only:

- CE Only:

Appliance Classification

Category: II

2H3P

(20, 30 / 37).

Flue Type: A1.

* - The burner operating pressure is to be measured at the manifold test point with two

burners operating at full setting. The operating pressure is ex-factory set, through the
appliance regulator and is not to be adjusted, apart from when carrying out gas
conversion, if required. (Refer to the ‘Gas Conversion’ section for details).

Gas Connection

Gas supply connection point is located at the rear of the appliance, approximately 130 mm from the
right hand side, 35 mm from the rear and 655 mm from the floor and is reached from beneath the
appliance. (Refer to the ‘Dimensions’ section).

Connection is ¾" BSP male thread.

Natural Gas (G20) Propane (G31)

Open Burner

(each)

Griddle

(each 300mm section)

Open Burner

(each)

Griddle

(each 300mm section)

Heat Input

(nett)

Nominal 6.5 kW 5.5 kW 6.5 kW 5.5 kW
Reduced 1.75 kW 1.85 kW 1.75 kW 1.95 kW

Gas Rate (nett)

Nominal 0.69 m3/hr 0.58 m3/hr 0.51 kg/hr 0.43 kg/hr
Reduced 0.19 m3/hr 0.20 m3/hr 0.14 kg/hr 0.15 kg/hr

Supply Pressure 20 mbar 30 /37 mbar

Burner Operating Pressure 9.5 mbar (*) 26 mbar (*)

Gas Connection See ‘Gas Connection’ information overleaf

Natural Gas LP Gas (Propane)

Input Rate (N.H.G.C.)

- each Open Burner

28 MJ/hr

(26,540 Btu/hr)

28 MJ/hr

(26,540 Btu/hr)

- each 300 mm Griddle Section

21 MJ/hr

(19,900 Btu/hr)

21 MJ/hr

(19,900 Btu/hr)

Supply Pressure

1.13 - 3.40 kPa

(4.5” - 13.5” w.c.)

2.75 - 4.50 kPa

(11” - 18.0” w.c.)

Operating Pressure

0.95 kPa (*)
(3.7” w.c.)

2.6 kPa (*)

(10.0” w.c.)

Gas Connection

3

/4” B.S.P. Male

5

Electrical Supply Requirements

Electrical Connection

RN8510 / RN8610GE / GEC Models Only

.

Electrical supply connection point is located at the rear of the appliance, approximately 80 mm from
the right hand side and 466 mm from the rear and 150 mm from the floor.

RN8810GE/GEC Models Only

.

Electrical supply connection point is located at the rear of the appliance, approximately 380 mm from
the right hand side, 466 mm from the rear and 150 mm from the floor.

When connecting a this electric appliance to the mains supply, ensure that the following is carried
out:-

• An isolating switch is fitted within 2 m of the appliance, but not on the appliance and in
such a position that the user does not have to reach across the cooking surface.

• Supply cord shall be oil-resistant, sheathed flexible cable and not lighter than ordinary
polychloroprene or other equivalent synthetic elastomer sheathed cord (as per AS / NZS
3191 part 2.10.11. or IEC 60245-IEC-57) e.g. HO5 RN-F Type.

• The branch supply line shall be individually overload protected to the correct current rating
and the supply chord shall be protected against any mechanical or thermal damage.

• A grommet is fitted around the wiring entry hole into the appliance.

• All wiring connections must be tight.

Refer to the appropriate wiring standards for the size of cable that is to be supplied to an appliance
for the current drawn on that line.

Specifications

WARNING:

T

HIS APPLIANCE MUST BE EARTHED. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY

QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

MODEL

1-Phase Connection

1P+N+E

230-240V

RN8510GE

5.5 kW,

22.6 Amps @ 235 V

5.5 kW

L1 - 7.2 Amps
L2 - 7.7 Amps
L3 - 7.7 Amps

RN8510GEC

5.8 kW,

23.9 Amps @ 235 V

5.8 kW

L1 - 8.5 Amps
L2 - 7.7 Amps
L3 - 7.7 Amps

RN8610GE

6.5 kW,

26.6 Amps @ 235 V

6.5 kW

L1 - 8.2 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

RN8610GEC

6.8 kW,

27.9 Amps @ 235 V

6.8 kW

L1 - 9.5 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

RN8810GE

6.5 kW,

26.6 Amps @ 235 V

6.5 kW

L1 - 8.2 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

RN8810GEC

6.8 kW,

27.9 Amps @ 235 V

6.8 kW

L1 - 9.5 Amps
L2 - 9.2 Amps
L3 - 9.2 Amps

3-Phase Connection

3P+N+E

400-415V

6

Dimensions

RN(L)8510GE / GEC

Refer to Page 8 for Cook Top Options

RN(L)8610GE / GEC

7

Dimensions

Refer to Page 8 for Cook Top Options

RN(L)8810GE / GEC

8

RN(L)8610GE / GEC

RN(L)8613GE / GEC

RN(L)8616GE / GEC

RN(L)8619GE / GEC

RN(L)8810GE / GEC

RN(L)8813GE / GEC

RN(L)8816GE / GEC

RN(L)8819GE / GEC

Dimensions

Cook Top Options

RN(L)8510GE / GEC

RN(L)8513GE / GEC

9

Installation Requirements

NOTE:

• It is most important that this appliance is installed correctly and that operation is correct
before use. Installation shall comply with local electrical, gas, health and safety
requirements.

• This appliance shall be installed with sufficient ventilation to prevent the occurrence of
unacceptable concentrations of health harmful substances in the room, the appliance is
installed in.

Waldorf Gas Range Convection Ovens are designed to provide years of satisfactory service, and correct
installation is essential to achieve the best performance, efficiency and trouble-free operation.
This appliance must be installed in accordance with National installation codes and in addition, in
accordance with relevant National / Local codes covering gas, electrical and fire safety.

Australia: - AS5601 - Gas Installations.
New Zealand: - NZS5261 - Gas Installation.
Australia / New Zealand: - AS / NZS3000 - Wiring Rules.
United Kingdom: - Gas Safety (Installation & Use) Regulations 1998.

- BS6173 - Installation of Catering Appliances.

- BS5440 1 & 2 - Installation Flueing & Ventilation.

- BS7671 - Requirements for Electrical Installation.

Ireland: - IS 820 - Non - Domestic Gas Installations.

Installations must be carried out by qualified persons only. Failure to install equipment to the
relevant codes and manufacturer’s specifications shown in this section will void the
warranty.
Components having adjustments protected (e.g. paint sealed) by the manufacturer are only
allowed to be adjusted by an authorised service agent. They are not to be adjusted by the
installation person.

Unpacking

• Remove all packaging and transit protection from the appliance including all protective plastic
coating from the exterior stainless steel panels.

• Check equipment and parts for damage. Report any damage immediately to the carrier and
distributor.

• Report any deficiencies to the distributor who supplied the appliance.

• Check that the available gas and electrical supply is correct to that shown on the rating plate located

on the front right hand corner of the bottom sill.

Location

1. Installation must allow for a sufficient flow of fresh air for the combustion air supply.

2. Installation must include adequate ventilation means, to prevent dangerous build up of combustion
products.

3. Never directly connect a ventilation system to the appliance flue outlet.

4. Position the appliance in its approximate working position.

5. All air for burner combustion is supplied from underneath the appliance. The legs must always be
fitted and no obstructions placed on the underside or around the base of the appliance, as
obstructions will cause incorrect operation and / or failure of the appliance.

NOTE: Do not obstruct or block the appliances flue. Never directly connect a ventilation

system to the appliance flue outlet.

Installation

Combustion Air Requirements:

RN8510GE / GEC RN8610GE / GEC RN8810GE / GEC

Natural Gas (G20) 29 m3/hr 44 m3/hr 58 m3/hr
LPG (G31) 30 m

3

/hr 45 m3/hr 60 m3/hr

10

Clearances

NOTE: Only non-combustible materials can be used in close proximity to this appliance.

* Side clearances can be 50mm when the adjacent surface is at least 100mm below the cooking

surface.

Assembly

This model is delivered completely assembled. Ensure that the legs are securely attached.

NOTE:

• This appliance is fitted with adjustable feet to
enable it to be positioned securely and level on
uneven floors. This should be carried out on
completion of the gas connection. Refer to the
'Gas Connection Section'.

• This appliance can also be fitted with rear rollers to
enable the appliance to be easily moved for
positioning and cleaning purposes. If desired,
these rollers are supplied in the packaging, with
the appliance. See below for fitting instructions.

Optional Accessories (Refer to Replacement Parts
List)

• Plinth Kit. For installation details, refer to the
instructions supplied with each kit.

Fitting Rear Rollers.

1. Raise the appliance from the floor by approx.
75 mm using suitable lifting equipment (i.e.
Palletiser / Forklift) to allow the rear adjustable
feet to be removed.

2. Unscrew and remove both the rear adjustable
feet from the rear leg housings.

3. Fit the rear roller to the rear leg housing and
align the screw hole in the side of the rear leg
housing with the threaded hole in the rear
roller.

4. Secure the rear roller to the leg support with
the bolt supplied and tighten the bolt using a
10mm A/F spanner.

5. Fit the second roller and tighten.

6. Lower the appliance back to the floor and
adjust the front adjustable feet to level the
appliance.

Installation

Combustible Surface Non Combustible Surface

Left / Right hand side 250mm (*) 0mm

Rear 50mm 0mm

Fig 1

Appliance

Base

Adjustable

Foot

Rear Roller

Assy

Rear Leg

Housing

Roller

Locating Bolt