Wahl RECHARGEABLE SHAVER Instructions Manual

Page 1
SHAVER
RECHARGEABLE SHAVER
INSTRUCTIONS
1
Page 2
SHAVER
Please read all instructions carefully to familiarise yourself
with your new Wahl shaver before using.
Save these instructions for further reference.
For any further assistance or information call Customer Services on
T: 01227 740066
or visit
W: www.wahl.co.uk
E: customer.services@wahl.co.uk
CONTENTS
GENERAL USER INFORMATION Page 3 IMPORTANT SAFEGUARDS Page 4 DESCRIPTION OF PARTS Page 9 OPERATING INSTRUCTIONS Page 10 CLEANING AND MAINTENANCE Page 14 TROUBLESHOOTING Page 18
LITHIUM-ION BATTERY REPLACEMENT REMOVAL AND DISPOSAL Page 19
WIRING Page 20 DISPOSAL Page 20 GUARANTEE Page 21
2
Page 3
SHAVER
GENERAL USER INFORMATION
Information about using the operation manual
Before using the appliance for the rst time,
you must read and understand the operation manual completely.
►Consider the operation manual as part of the
product and store it in a safe and accessible place.
►Include this operation manual if passing the
appliance on to a third party.
In the case of conicts with national safety
specications or instructions, the national
requirements must be followed.
Explanation of symbols and notes
DANGER
Danger of electric shock which may result in serious physical injury or death.
DANGER
Danger of explosion which may result in serious physical injury or death.
WARNING
Warning of possible physical injury or a health risk.
CAUTION
Information about danger of material damage.
Note with useful information and tips.
Action to be taken by owner.
Carry out these actions in the sequence described.
1.
·
List
3
Page 4
SHAVER
Please retain this leaet for future reference.
READ ALL INSTRUCTIONS BEFORE USING.
IMPORTANT SAFEGUARDS
When using this electrical appliance, especially when children are present, basic safety precautions should
always be observed including the following.
Requirements
Read the instruction manual in full to familiarise
yourself with the product before the rst use.
►This appliance can be used by children
from aged 14 years and above and persons
with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
►Use this appliance only for its intended purpose. This shaver is intended exclusively for trimming
human hair. The shaver is designed for private home use and must not be used for commercial purposes.
►The shaver must only be used indoors.
4
Page 5
SHAVER
Do not use the device to cut articial hair or
animal hair
►Children must not play with packaging
material. Do not allow children to play with plastic bags. Danger of suffocation.
►The hand-held shaver can be rinsed under
running water. DANGER! Disconnect the charger from the
shaver rst.
Hazards
Danger! Electric shock due to damage to appliance
Do not operate the shaver if the shaver, the
charger or the cable shows visible signs of damage or if the shaver has been dropped.
►Connect the cable to the shaver before
plugging the charger into a power point.
►Only connect the charger to a properly
installed easy to access power point supplying voltage matching the rating plate. The power point must still be easily accessible after connection.
►Ensure that the cable cannot be damaged by
sharp edges or hot surfaces.
►Ensure that the cable is not trapped or
crushed.
►Always pull at the charger and never pull on
5
Page 6
SHAVER
the cable when unplugging the charger.
►Remove the charger from the power point:
1. After each use
2. After each charging process
3. If a fault occurs
4. Before connecting the device to the cable
5. Before cleaning the shaver
To avoid any risk, do not make any changes to
the shaver or accessories.
►Any servicing or repair must be performed
by Wahl (UK) Ltd or a suitably qualied
professional.
►The use of attachments that are not supplied by
the manufacturer may cause re, electric shock
or injury and damage to the appliance.
Danger! Electric shock due to penetration of liquid.
Do not use this device – with the charger connected
– in the vicinity of bathtubs, showers, washbasins or
other vessels containing water.
Protect the cable and the charger from moisture,
dripping water or splash water.
► Do not operate the device with the charger connected
if your hands are wet.
► Do not immerse the cable and the charger in water or
other liquids or rinse them under running water.
► Unplug the charger from the power point before
6
Page 7
SHAVER
cleaning the shaver and its parts under running water.
If the device has fallen into water, pull out the charger
immediately, and only then remove the device from the water. Do not use the device again, but have it
checked by a specialist.
If the device is used in a bathroom, the cord
connecting the device to the mains power must
be pulled out after use, as the proximity of water represents a hazard, even when the device is
switched off.
► Installation of a residual current device (FI/RCD) with
a rated residual operating current of no more than 30 mA is recommended to provide additional protection.
► Ask your electrician for advice. The installation should
only be carried out by a qualied electrician.
Danger of explosion
Protect rechargeable batteries against mechanical
damages. Danger of re.
Do not expose the shaver to direct sunshine or heat.
The ambient temperature should not be lower than 5 °C or higher than 35 °C.
► The charge contacts on the shaver must not be
connected by metallic objects. Rechargeable batteries
may overheat and explode.
► Charge the shaver only with the charger provided. ► Should the electrolyte solution leak out of the
rechargeable batteries, avoid contact with eyes,
7
Page 8
SHAVER
mouth, nose and skin. Rinse immediately with plenty
of clean water and consult a doctor. The electrolyte solution can cause irritation.
Warning! Injuries due to incorrect handling
► Place the cable in such a way that no one trips over
it or steps on.
Do not use the device on open wounds, cuts,
sunburn or blisters.
► Do not operate the shaver if the device or cutting
elements are damaged or defective.
► The cutting blades are sharp. Handle with care. ► Keep the shaver away from your eyes. ► Always switch off the shaver before cleaning it.
Caution! Danger of product damage
Use the original accessories only.
Never place the shaver on hot surfaces (e.g. hob plates) or near heat sources or open fire.
Do not cover the charger to prevent overheating.
In order to avoid damages to the shaving foil, do not
exert excessive pressure on the shaving foil.
Do not use any harsh or abrasive cleaning agents.
NOTE:
We advise you not to use shaving gel, since
this may cause the shaving foil and cutting blades to stick to each other.
8
Page 9
SHAVER
3
8
4
10
7
5
2
1 9
DESCRIPTION OF PARTS
1. Charge socket
2. On/o󰀨 switch
3. Cutter bar assembly
4. Flex foil head
5. Long hair pop up trimmer
6. Long hair trimmer switch
7. Shaver head release button
8. Foil guard
9. Charger contacts
10. Spring clip
NOTE: Remove LED label before rst use.
6
9
Page 10
SHAVER
OPERATING INSTRUCTIONS
TIPS FOR FIRST-TIME USERS
If you are using an electric shaver for the rst time, your
skin will probably need to condition itself to this new shaving technique.
Start on the easiest part of the face rst, usually the smooth
portion of the face below the ear. Shave with a light touch and use your Wahl Shaver exclusively for three to four
weeks, or longer if you have sensitive skin or if your whiskers grow at di󰀨erent angles in certain areas. Initially your shaves may not be as close as you would like, and your skin may become a bit irritated. But if you stick with it, you will
eventually get great shaves.
If you go several days without shaving and your beard gets
a bit long, use the pop-up trimmer to go over your beard,
catching all the longer hairs and setting up the remaining stubble for the foil to shave smooth and clean.
If you have been using another type of electric shaver before,
there may also be a period of conditioning prior to receiving maximum results.
QUICK TIPS & HANDY REMINDERS
1. If you are a rst-time electric shaver user, or changing from another brand, there will be a 2 to 3 week (or less)
adjustment period while your face and beard adapts to the new foil.
2. When you open your package, charge your shaver for 1
hour before the rst shave or until charging is complete.
3. Replace the foil head and cutter bars every 12 months or if foils are damaged. Replacement foils can be ordered by contacting WAHL customer Services.
10
Page 11
SHAVER
4. Be sure to clean the shaver, cutter bars and foil after every three or four shaves.
5. Use the pop-up long-hair trimmer to snip stray hairs.
6. Keep using and both your face and beard will adapt to the shaver.
TRAVEL LOCK
The Wahl Shaver comes with an electronic travel lock to avoid accidental activation while transporting. Hold power button down for 3 seconds to engage travel lock. Hold power button down for 3 seconds to disengage travel lock.
When travel lock is active, pressing the power button will cause the LED(s) to ash for 1 second.
NOTE: The shaver will not charge while the travel lock is engaged
CHARGING OPERATION
The shaver cannot be overcharged, so you may charge it as often as desired. However, periodic recharging of the shaver, rather than continuous recharging, will prolong battery life.
60 minutes charge time will provide you with 90 minutes cordless operation.
MODELS WITH 1 LED
Charge when shaver seems to lose power or run slower. The
charging LED will light up while charging. LED will turn o󰀨 when
charging is complete.
MODELS WITH 2 LEDS
The red LED will ash for one second when turning o󰀨 the shaver when it is time to charge (below 10%). The blue LED will light up while charging. LED will turn o󰀨 when
charging is complete.
11
Page 12
SHAVER
MODELS WITH 5 LEDS
The LED meter will show the amount of charge left on the
shaver.The fewer lights that are lit, the lower the charge on the battery is.The red LED will ash for one second when turning o󰀨 the shaver when it is time to charge (below 10%). While charging, the LED meter will show the progression of charging. All LEDs will turn o󰀨 when charging is complete.
WARNING. Do not operate the shaver if the shaving foil is damaged.
SHAVING PROCEDURES FOR FAST, CLOSE SHAVES
We suggest that you thoroughly cleanse and completely dry your skin prior to shaving. For maximum speed and
e󰀩ciency, hold the shaver so that both
screens are in contact with the skin.
When shaving the upperlip or neck, hold
shaver so that the uppermost screen is in contact with skin. Shave both with and against the grain of
the beard, and stretch the skin taut in the path of the shaver.
Guide the dual foil heads gently back and forth, primarily against the grain of the beard. Do not press screen heads hard against face. Heavy scrubbing action with the shaver could damage the foil and will not result in a closer shave. Always replace the foil guard to protect the delicate dual foil
heads when shaver is o󰀨.
12
Page 13
SHAVER
SHAVING HEAVY BEARD GROWTH
Begin shaving in a less dense area of the beard. Move the shaver in a circular motion on a small area of the
face (this picks up the hairs that grow in all directions).
When you see that this small area is shaved clean, gradually move into a new area while still using the circular
motion.Continue this motion, one small section at a time, until entire face is shaved.
If your beard has more than 3 days of growth, use the pop-up Long-Hair Trimmer to cut the beard down to about a one-day growth before using the shaver foil.
LONG-HAIR TRIMMER OPERATION
Your shaver features a special long-
hair trimmer located on the back of the shaver which telescopes up from the foil head for precise and
easy trimming of sideburns, beards or moustaches,and for removing long hairs from the neck. And, as mentioned earlier, it can be used to
“knock down” heavy beard growth prior to shaving with the foil.
To use, remove Foil Guard and simply push the Long-Hair Trimmer Switch in an upward motion until trimmer slides
(clicks) into position. Push On/O󰀨 Switch. Then begin
trimming/styling
13
Page 14
SHAVER
CLEANING AND MAINTENANCE SHAVER HEAD CARE
For maximum performance, we
recommend you clean your shaver
after every few shaves. Any servicing,
other than replacement of foil head and
cutter bars, should be performed by an
authorised Wahl Service Center or Wahl customer services.
To clean, turn shaver “OFF” and remove the foil head by pushing the shaver head release buttons on the sides of the shaver and lifting the foil head upward.
Lightly tap the open side of the foil head on a hard surface to remove the majority of loose stubble particles.
Be careful not to tap the foil.
For easy cleaning, you may
rinse your shaver with water.
While the foils can be rinsed,
we recommend removing the
foil head, and rinsing the cutter
bars. This will allow any hairs still on the cutter bars to be washed away. Leaving the foil
head on while rinsing makes in more di󰀩cult for hairs to be
washed clean.
14
Page 15
SHAVER
TO REMOVE CUTTER BAR
Turn shaver o󰀨. Remove the foil
head and, holding the shaver in one hand, gently pull up on cutter bar. Be sure your thumb and rst
nger are positioned at each end of
the cutter bar.
WARNING: Handle cutting components with care to avoid personal injury.
NOTE: If you do not hold the
cutter bar as shown, brushing the
blades could result in damage to the assembly.
When the foil head and cutter bars
are removed from the shaver, an
alternate cleaning method is to rinse them under running water. Simply let
them air dry. After cleaning, replace
the cutter bars by pressing down
gently. Carefully replace the foil head,
snapping it into place.
From time to time, depending on the density of your beard,
you will need to replace the cutters and foils. If you notice
that it is taking you longer to shave, or if your face starts to feel some irritation, or if the foil seems to become warm to the touch, it is probably time to replace the cutters and foils.
Replace the cutters and foils only with WAHL parts. Please contact Wahl customer services for replacement.
15
Page 16
SHAVER
OILING THE FOILS & CUTTER BAR
Oil lubrication helps maintain smooth blade movement and shaving performance. If the shaver is regularly cleaned under water. The Foils should be oiled at least once per week. Use clipper oil or shaver oil.
Instructions: When foils and blades are clean and dry,
apply a drop of oil to the top of each foil and on top of the
center cutter bar. Use nger to gently spread the oil over
the surface. Turn the shaver on for 10 seconds to help
distribute the oil onto the blades below. Turn o󰀨 shaver and
use a tissue or soft cloth to wipe any excess oil from the surface.
CLEANING & OILING TRIMMER BLADES
Clean with the included brush. For best results, put one or two drops of blade oil on the blades only when necessary,
or approximately once a month. Motor bearings are permanently lubricated—do not attempt
to oil. When oiling your shaver, turn the shaver “ON - I,” hold
the unit with the blades facing DOWN and squeeze one or
two drops of oil onto the blades. Wipe o󰀨 excess oil with
soft cloth. Blade oil can be purchased from Wahl customer services.
NOTE: DO NOT OVER OIL!
Excessive oiling or application of liquids will cause damage if allowed to seep back into motor.
FOIL & BLADE CARE
Trimmer blades have precision-hardened, ground and lapped cutting teeth. Foils, cutter bar, and blades should be
handled carefully and never bumped or used to cut dirty or abrasive material.
16
Page 17
SHAVER
STORAGE
Before storing your shaver, use the cleaning brush to whisk any loose hairs from the unit, foils, cutter bar, and blades.
Store unit in such a manner so that blades are protected
from damage. When the shaver is not in use, the shaver
foil/blade guard attachment should be in place to protect the blades. This appliance should be stored in a manner where it is not
subjected to crushing, heating above 100°C (212°F), or
incineration.
CORD CARE
The cord should not be used to pull the shaver. Freedom of movement needs to be maintained. Care should be used to keep the cord untwisted and undamaged.
When stored, the cord should be coiled and replaced neatly
in its original package or storage pouch.
WET/DRY USE
NOTE: Do not submerge shaver in more than 3 feet
of water or for more than 30 minutes to prevent water
ingress into the electronics. Warranty is void if shaver is submerged beyond these limitations. The Wahl shaver is designed to be water resistant and
shower proof (IPX7). This lets you use your Wahl shaver in
the shower or at the sink without worry and makes it easy to clean under running water.
NOTE: The shaver is for wet/dry use. The shaver will
not run while the cord is attached for safety.
17
Page 18
SHAVER
TROUBLESHOOTING
WARNING!
Do not attempt to repair the shaver yourself.
Always remove the charger from the socket whenever
a fault occurs.
Fault Please check the following
No function Is there power to the power
point? Batteries low?
The shaving performance deteriorates
Clean the cutting bar, if
needed replace the foil and cutter bar.
If you are experiencing a fault which is not listed here,
please do not hesitate to contact our Customer Services.
Repairs must only be carried out by qualied technicians or
by our Service Centre.
18
Page 19
SHAVER
LITHIUM-ION BATTERY REPLACEMENT REMOVAL AND DISPOSAL
For battery replacement the entire, intact clipper or trimmer should be sent to: Wahl (UK) Ltd Customer Services (the address can be found on the reverse of this booklet) or taken to a suitably qualied professional.
The battery should only be replaced by the original
manufacturers spare, for safety reasons a substitute
should not be used.
Do not attempt to remove the battery. Lithium-Ion batteries can explode, catch re, and/or cause burns if disassembled, damaged or exposed to water or high
temperatures.
LITHIUM BATTERY DISPOSAL
Do not dispose of this product or the Lithium battery in the normal household waste.
The product should be returned to Wahl Customer
Services where we o󰀨er a take back service or taken to a
local collection facility where they will be dealt with safely and sent for the appropriate recycling.
19
Page 20
SHAVER
WIRING
WARNING: THIS PRODUCT MUST ONLY BE
USED WITH THE TRANSFORMER SUPPLIED.
SHOULD A REPLACEMENT BE REQUIRED
CONTACT WAHL CUSTOMER SERVICE ON
01227 740066.
DISPOSAL
Handle with care! Environmental damage in the
case of incorrect disposal.
Correct disposal will ensure environmental protection
and prevent any potentially harmful impacts on
people and the environment.
Adhere to the relevant legal requirements when
disposing of the appliance. Information on the
disposal of electrical and electronic appliances in the
European Community:
20
Page 21
SHAVER
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT DIRECTIVE 2002/96/EC (WEEE)
At the end of this products life it should not be disposed of with general household waste. Care should be taken to dispose of in a suitable manner in accordance with your Local Authority regulation.
21
Page 22
SHAVER
GUARANTEE
This product is guaranteed against defects in material and workmanship for a period of 5 years from the date of original purchase or receipt as a gift.
Should this product become defective during the
guarantee period, return it to the store of purchase
together with your proof of purchase for repair or replacement.
Alternatively within the guarantee period you can return
the product to Wahl (UK) Ltd who will repair any such defect or elect to replace the product or any part of it, without charge, provided that there is proof of purchase. Should a replacement be o󰀨ered this will not extend the
original guarantee period.
The guarantee becomes invalid in the case of misuse,
alteration or repair by unauthorised persons.
This guarantee does not include blades, cables, shaver heads, foils and cutters etc which are consumable parts.
This product is designed for domestic use only and use within a professional environment will invalidate the guarantee.
This guarantee in no way a󰀨ects your rights under
statutory law in the United Kingdom.
22
Page 23
SHAVER
23
Page 24
SHAVER
WAHL (UK) LIMITED
STERLING HOUSE, CLIPPER CLOSE, RAMSGATE, KENT
CT12 5GG
CUSTOMER SERVICES T: 01227 740066 www.wahl.co.uk
Form No. 91590-100 Rev1 07-18
24
Loading...