Page 1
Data sheet | Item number:280-816
4-conductor carrier terminal block; for DIN-rail 35 x 15 and 35 x 7.5; 2.5
mm²; CAGE CLAMP®
Color:
Item description
Note:
Terminating Aluminum Conductors
WAGO spring clamp terminal blocks are suitable for solid aluminum conductors up to 4mm²/12AWG if WAGO “Alu-Plus” Contact Paste is used for
termination.
“Alu-Plus” Contact Paste Advantages:
Automatically destroys the oxide film during clamping.
Prevents fresh oxidation at the clamping point.
Prevents electrolytic corrosion between aluminum and copper conductors (in the same terminal block).
Provides long-term protection against corrosion.
Using terminal blocks with CAGE CLAMP® Spring Pressure Connection Technology, and aluminum conductors must first be cleaned with a blade
then immediately be inserted into the clamping units filled with “Alu-Plus” Contact Paste.
It is also possible to apply WAGO “Alu-Plus” on the whole surface of the aluminum conductor before termination.additionally
Please note that the nominal currents must be adapted to the reduced conductivity of the aluminum conductors:
2.5mm² (14 AWG) = 16 A
4mm² (12 AWG) = 22 A
Data
Electrical data
280-816
01.05.2019Page /1 13
Page 2
Data sheet | Item number:280-816
Ratings per IEC/EN 60664-1
Rated voltage (III / 3) 400 V
Rated impulse voltage (III / 3) 6 kV
Rated current 10 A
Connection data
Connection technology
CAGE CLAMP
®
Actuation type Operating tool
Connectable conductor materials Copper
Aluminum
Solid conductor 0.08 … 2.5mm²/ 28 … 12AWG
Fine-stranded conductor 0.08 … 2.5mm²/ 28 … 12AWG
Strip length 8 … 9mm/ 0.31 … 0.35inch
Note (conductor cross-section) 12 AWG: THHN, THWN
Total number of connection points 4
Total number of potentials 2
Number of levels 1
Type of wiring Front-entry wiring
Geometrical Data
Width 5mm/ 0.197inch
Height from upper-edge of DIN-35 rail 28mm/ 1.102inch
Depth 75mm/ 2.953inch
Mechanical data
Design horizontal
Type of mounting DIN-35 rail
Marking level Center marking
Material Data
Color gray
Insulating material Polyamide 66 (PA 66)
Fire load 0.141 MJ
Weight 8.86g
Commercial data
Product Group 1 (Rail Mounted Terminal Blocks)
Country of origin DE
GTIN 4044918557009
280-816
01.05.2019Page /2 13
Page 3
Data sheet | Item number:280-816
Customs Tariff No. 85369010000
Compatible products
Carrier rail
Item no.: 210-112
Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; according to EN 60715; "Hole width 25
mm
210-112
Item no.: 210-113
Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; unslotted; according to EN 60715
210-113
Item no.: 210-114
Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; unslotted; similar to EN 60715
210-114
Item no.: 210-115
Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; according to EN 60715; "Hole width 18
mm
210-115
Item no.: 210-118
Steel carrier rail; 35 x 15 mm; 2.3 mm thick; 2 m long; unslotted; according to EN 60715
210-118
Item no.: 210-196
Aluminum carrier rail; 35 x 8.2 mm; 1.6 mm thick; 2 m long; unslotted; similar to EN 60715
210-196
Item no.: 210-197
Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; slotted; similar to EN 60715
210-197
Item no.: 210-198
Copper carrier rail; 35 x 15 mm; 2.3 mm thick; 2 m long; unslotted; according to EN 60715
210-198
Item no.: 210-504
Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; slotted; galvanized; according to EN 60715
210-504
Item no.: 210-505
Steel carrier rail; 35 x 7.5 mm; 1 mm thick; 2 m long; unslotted; galvanized; according to EN 60715
210-505
Item no.: 210-506
Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; unslotted; galvanized; similar to EN 60715
210-506
Item no.: 210-508
Steel carrier rail; 35 x 15 mm; 1.5 mm thick; 2 m long; slotted; galvanized; similar to EN 60715
210-508
Jumper
Item no.: 210-103
Wire commoning chain; insulated; 50 connections
210-103
280-816
01.05.2019Page /3 13
Page 4
Data sheet | Item number:280-816
Item no.: 210-123
Wire commoning chain; insulated; 50 connections
210-123
Item no.: 280-482
Comb-style jumper bar; insulated; 2-way; IN = IN terminal block
280-482
Item no.: 280-483
Comb-style jumper bar; insulated; 3-way; IN = IN terminal block
280-483
Item no.: 280-484
Comb-style jumper bar; insulated; 4-way; IN = IN terminal block
280-484
Item no.: 280-485
Comb-style jumper bar; insulated; 5-way; IN = IN terminal block
280-485
Item no.: 280-490
Comb-style jumper bar; insulated; 10-way; IN = IN terminal block
280-490
Item no.: 280-492
Alternate comb-style jumper bar; insulated; 2-way; IN = IN terminal block
280-492
Item no.: 709-110
Wire commoning chain; insulated; 4 connections; 3 x 110 mm
709-110
Item no.: 709-111
Wire commoning chain; insulated; 3 connections; 2 x 120 mm
709-111
Item no.: 709-112
Wire commoning chain; insulated; 3 connections; 2 x 170 mm
709-112
End plate
Item no.: 280-314
End and intermediate plate; 2.5 mm thick
280-314
Item no.: 280-315
End and intermediate plate; 2.5 mm thick
280-315
Marking accessories
Item no.: 2009-115
WMB-Inline; for Smart Printer; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
Item no.: 2009-115/000-002
WMB-Inline; for Smart Printer; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-002
Item no.: 2009-115/000-006
WMB-Inline; for smartPRINTER; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-006
Item no.: 2009-115/000-007
WMB-Inline; for Smart Printer; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-007
Item no.: 2009-115/000-012
WMB-Inline; for smartPRINTER; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-012
280-816
01.05.2019Page /4 13
Page 5
Data sheet | Item number:280-816
Item no.: 2009-115/000-017
WMB-Inline; for Smart Printer; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-017
Item no.: 2009-115/000-023
WMB-Inline; for Smart Printer; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-023
Item no.: 2009-115/000-024
WMB-Inline; for smartPRINTER; on reel; stretchable 5 - 5.2 mm; plain; snap-on type
2009-115
/000-024
Item no.: 793-501
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
Item no.: 793-501/000-002
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-002
Item no.: 793-501/000-005
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-005
Item no.: 793-501/000-006
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-006
Item no.: 793-501/000-007
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-007
Item no.: 793-501/000-012
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-012
Item no.: 793-501/000-017
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-017
Item no.: 793-501/000-023
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-023
Item no.: 793-501/000-024
WMB marking card; as card; not stretchable; plain; snap-on type
793-501
/000-024
Item no.: 793-5501
WMB marking card; as card; for terminal block width 5 - 17.5 mm; stretchable 5 - 5.2 mm; plain; snapon type
793-5501
Item no.: 793-5501/000-002
WMB marking card; as card; for terminal block width 5 - 17.5 mm; stretchable 5 - 5.2 mm; plain; snapon type
793-5501
/000-002
Item no.: 793-5501/000-005
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-005
280-816
01.05.2019Page /5 13
Page 6
Data sheet | Item number:280-816
Item no.: 793-5501/000-006
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-006
Item no.: 793-5501/000-007
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-007
Item no.: 793-5501/000-012
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-012
Item no.: 793-5501/000-017
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-017
Item no.: 793-5501/000-023
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-023
Item no.: 793-5501/000-024
WMB marking card; as card; stretchable 5 - 5.2 mm; plain; snap-on type
793-5501
/000-024
ferrule
Item no.: 216-101
Ferrule; Sleeve for 0.5 mm² / AWG 22; uninsulated; electro-tin plated
216-101
Item no.: 216-102
Ferrule; Sleeve for 0.75 mm² / AWG 20; uninsulated; electro-tin plated
216-102
Item no.: 216-103
Ferrule; Sleeve for 1 mm² / AWG 18; uninsulated; electro-tin plated
216-103
Item no.: 216-104
Ferrule; Sleeve for 1.5 mm² / AWG 16; uninsulated; electro-tin plated
216-104
Item no.: 216-201
Ferrule; Sleeve for 0.5 mm² / 20 AWG; insulated; electro-tin plated
216-201
Item no.: 216-202
Ferrule; Sleeve for 0.75 mm² / 18 AWG; insulated; electro-tin plated
216-202
Item no.: 216-203
Ferrule; Sleeve for 1 mm² / AWG 18; insulated; electro-tin plated
216-203
Item no.: 216-204
Ferrule; Sleeve for 1.5 mm² / AWG 16; insulated; electro-tin plated
216-204
Item no.: 216-301
Ferrule; Sleeve for 0.25 mm² / AWG 24; insulated; electro-tin plated
216-301
Item no.: 216-302
Ferrule; Sleeve for 0.34 mm² / 22 AWG; insulated; electro-tin plated
216-302
plug
Item no.: 280-850
Fuse plug; with soldered miniature fuse; 250 mA FF; 5 mm wide
280-850
280-816
01.05.2019Page /6 13
Page 7
Data sheet | Item number:280-816
Item no.: 280-850/281-413
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 15 - 30 V; 250 mA FF; 5
mm wide
280-850
/281-413
Item no.: 280-850/281-414
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 30 - 65 V; 250 mA FF; 5
mm wide
280-850
/281-414
Item no.: 280-850/281-415
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); AC 15 - 30 V; 250 mA FF; 5
mm wide
280-850
/281-415
Item no.: 280-852
Fuse plug; with soldered miniature fuse; 500 mA FF; 5 mm wide
280-852
Item no.: 280-852/281-413
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 15 - 30 V; 500 mA FF; 5
mm wide
280-852
/281-413
Item no.: 280-852/281-414
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 30 - 65 V; 500 mA FF; 5
mm wide
280-852
/281-414
Item no.: 280-852/281-415
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); AC 15 - 30 V; 500 mA FF; 5
mm wide
280-852
/281-415
Item no.: 280-854
Fuse plug; with soldered miniature fuse; 1 A FF; 5 mm wide
280-854
Item no.: 280-854/281-413
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 15 - 30 V; 1 A FF; 5 mm
wide
280-854
/281-413
Item no.: 280-854/281-414
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 30 - 65 V; 1 A FF; 5 mm
wide
280-854
/281-414
Item no.: 280-854/281-415
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); AC 15 - 30 V; 1 A FF; 5 mm
wide
280-854
/281-415
Item no.: 280-856
Fuse plug; with soldered miniature fuse; 2 A FF; 5 mm wide
280-856
Item no.: 280-856/281-413
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 15 - 30 V; 2 A FF; 5 mm
wide
280-856
/281-413
Item no.: 280-856/281-414
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); DC 30 - 65 V; 2 A FF; 5 mm
wide
280-856
/281-414
Item no.: 280-856/281-415
Fuse plug; with soldered miniature fuse; with indicator lamp; LED (red); AC 15 - 30 V; 2 A FF; 5 mm
wide
280-856
/281-415
Insulation stop
280-816
01.05.2019Page /7 13
Page 8
Data sheet | Item number:280-816
Item no.: 280-470
Insulation stop; 0.08 - 0.2 mm² "s" (0.14 mm² "f-st"); 5 pieces/strip
280-470
Item no.: 280-471
Insulation stop; 0.25 - 0.5 mm²; 5 pieces/strip
280-471
Item no.: 280-472
Insulation stop; 0.75 - 1 mm²; 5 pieces/strip
280-472
tools
Item no.: 210-657
Operating tool with partially insulated shaft; Blade (3.5 x 0.5) mm; short
210-657
Item no.: 210-658
Operating tool with partially insulated shaft; Blade (3.5 x 0.5) mm; short; angled
210-658
Item no.: 210-720
Operating tool with partially insulated shaft; Type 2, blade (3.5 x 0.5) mm
210-720
General accessories
Item no.: 280-801
Empty component plug housing
280-801
Item no.: 280-801/281-411
Component plug; for carrier terminal blocks; 2-pole; with diode 1N4007; 5 mm wide
280-801
/281-411
Item no.: 280-801/281-413
Component plug; for carrier terminal blocks; 1-pole; LED (red); 24 VDC; 5 mm wide
280-801
/281-413
Item no.: 280-801/281-414
Component plug; for carrier terminal blocks; 1-pole; LED (red); 48 VDC; 5 mm wide
280-801
/281-414
Item no.: 280-801/281-415
Component plug; for carrier terminal blocks; 1-pole; LED (red); 5 mm wide
280-801
/281-415
Item no.: 280-801/281-416
Component plug; for carrier terminal blocks; 1-pole; LED (red); 5 mm wide
280-801
/281-416
Item no.: 280-801/281-417
Component plug; for carrier terminal blocks; 1-pole; 5 mm wide
280-801
/281-417
Item no.: 280-801/281-418
Component plug; for carrier terminal blocks; 1-pole; 5 mm wide
280-801
/281-418
Item no.: 280-801/281-420
Component plug; for carrier terminal blocks; 2-pole; with LED and recovery diode; 5 mm wide
280-801
/281-420
Item no.: 280-801/281-421
Component plug; for carrier terminal blocks; 2-pole; with LED and recovery diode; 5 mm wide
280-801
/281-421
280-816
01.05.2019Page /8 13
Page 9
Data sheet | Item number:280-816
Item no.: 280-802
Empty component plug housing
280-802
Item no.: 280-804
Empty component plug housing; 10 mm wide; Type 3; 4-pole
280-804
Item no.: 286-110
Empty component plug housing; Type 9; 10 mm wide; 4-pole
286-110
Item no.: 286-111
Empty component plug housing; Type 10; 15 mm wide; 6-pole
286-111
Item no.: 286-112
Empty component plug housing; Type 11; 20 mm wide; 8-pole
286-112
Item no.: 286-113
Empty component plug housing; Type 12; 25 mm wide; 10-pole
286-113
Item no.: 286-304
Relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Limiting continuous current: 7
A; Red status indicator; Module width: 15 mm
286-304
Item no.: 286-304/004-000
Relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Limiting continuous current: 7
A; Path; Red status indicator; Module width: 15 mm
286-304
/004-000
Item no.: 286-307/004-000
Relay module; Nominal input voltage: 110 VDC; 1 changeover contact; Limiting continuous current: 7
A; Path; Red status indicator; Module width: 15 mm
286-307
/004-000
Item no.: 286-312
Relay module; Relay with 2 changeover contacts (2u)
286-312
Item no.: 286-312/004-000
Relay module; Nominal input voltage: 24 VDC; 2 changeover contacts; Limiting continuous current: 7
A; Path; Red status indicator; Module width: 20 mm
286-312
/004-000
Item no.: 286-316
Relay module; Nominal input voltage: 220 VDC; 2 changeover contacts; Limiting continuous current:
7 A; Red status indicator; Module width: 20 mm
286-316
Item no.: 286-320
Relay module; Nominal input voltage: 24 VDC; 1 break and 1 make contact; Limiting continuous
current: 6 A; Red status indicator; Module width: 20 mm
286-320
Item no.: 286-320/004-000
Relay module; Nominal input voltage: 24 VDC; 1 break and 1 make contact; Path; Red status
indicator; Module width: 20 mm
286-320
/004-000
Item no.: 286-328
Relay module; Nominal input voltage: 24 VDC; 2 make contact; Limiting continuous current: 6 A; Red
status indicator; Module width: 20 mm
286-328
Item no.: 286-328/004-000
Relay module; Nominal input voltage: 24 VDC; 2 make contact; Limiting continuous current: 6 A; Path;
Red status indicator; Module width: 20 mm
286-328
/004-000
Item no.: 286-336/001-000
Relay module; Nominal input voltage: 24 VDC; 2 break and 2 make contacts; Red status indicator;
Module width: 25 mm
286-336
/001-000
280-816
01.05.2019Page /9 13
Page 10
Data sheet | Item number:280-816
Item no.: 286-344/004-000
Relay module; Nominal input voltage: 24 VDC; 3 break contacts and 1 make contact; Path; Red status
indicator; Module width: 25 mm
286-344
/004-000
Item no.: 286-352/004-000
Relay module; Nominal input voltage: 24 VDC; 4 make contacts; Limiting continuous current: 5 A;
Path; Red status indicator; Module width: 25 mm
286-352
/004-000
Item no.: 286-364
Relay module; Nominal input voltage: 24 VDC; 1 make contact; Limiting continuous current: 5 A; Red
status indicator; Module width: 10 mm
286-364
Item no.: 286-364/004-000
Relay module; Nominal input voltage: 24 VDC; 1 make contact; Path; Red status indicator; Module
width: 10 mm
286-364
/004-000
Item no.: 286-368
Relay module; Nominal input voltage: 24 VDC; 1 break contact; Limiting continuous current: 5 A; Red
status indicator; Module width: 10 mm
286-368
Item no.: 286-368/004-000
Relay module; Nominal input voltage: 24 VDC; 1 break contact; Limiting continuous current: 5 A; Path;
Red status indicator; 10 mm wide
286-368
/004-000
Item no.: 286-376
Relay module; Nominal input voltage: 24 VDC; 1 make contact; Limiting continuous current: 5 A; for
switching higher DC loads; Red status indicator; Module width: 15 mm
286-376
Item no.: 286-380
Bistable relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Limiting continuous
current: 6 A; Red status indicator; Module width: 15 mm
286-380
Item no.: 286-381
Bistable relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Limiting continuous
current: 6 A; Red status indicator; Module width: 15 mm
286-381
Item no.: 286-394/004-000
Relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Path; Red status indicator;
Module width: 15 mm
286-394
/004-000
Item no.: 286-427
Timer relay module; Nominal input voltage: 24 VDC; Limiting continuous current: 5 A; Pulse
lengthening: 1 … 10 s; Red status indicator; Module width: 20 mm
286-427
Item no.: 286-507
Relay module; Nominal input voltage: 115 VAC; 1 changeover contact; Limiting continuous current: 7
A; Red status indicator; Module width: 15 mm
286-507
Item no.: 286-508
Relay module; Nominal input voltage: 230 VAC; 1 changeover contact; Limiting continuous current: 7
A; Red status indicator; Module width: 15 mm
286-508
Item no.: 286-516
Relay module; Nominal input voltage: 230 VAC; 2 changeover contacts; Limiting continuous current:
7 A; Red status indicator; Module width: 15 mm
286-516
Item no.: 286-573
Latching relay module; Nominal input voltage: 24 VDC; 1 changeover contact; Limiting continuous
current: 6 A; Red status indicator; Module width: 17 mm
286-573
Item no.: 286-604/004-000
Timer relay module; Nominal input voltage: 24 VDC; Limiting continuous current: 6 A; On-delay: 10 …
100 s; Red status indicator; Module width: 20 mm
286-604
/004-000
Item no.: 286-640
280-816
01.05.2019Page /10 13
Page 11
Data sheet | Item number:280-816
Timer relay module; Nominal input voltage: 24 VDC; Limiting continuous current: 6 A; Path;
Multifunction/Multitime; Yellow status indicator; Module width: 6 mm
286-640
Item no.: 286-640/004-000
Multifunction timing relay module; Relay with 1 changeover contact (1u); 4 time ranges; for railway
operations; 4 functions
286-640
/004-000
Item no.: 286-661
Current flow monitoring module; AC current flow monitoring module; 80 mA ... 6 A
286-661
Item no.: 286-662
Current flow monitoring module; DC current flow monitoring module; 0.4 A ... 3.5 A; Relay with 1 make
contact (1a)
286-662
Item no.: 286-664
Current flow monitoring module; AC current flow monitoring module; 1 A ... 10 A; Adjustable; Relay
with 1 changeover contact (1u)
286-664
Item no.: 286-665
Current flow monitoring module; Relay with 1 changeover contact (1u); adjustable
286-665
Item no.: 286-721
Optocoupler module; Nominal input voltage: 24 VDC; Output voltage range: 15 … 30 VDC; Limiting
continuous current: 5 A; 3-wire connection/low-side switching; Red status indicator; Module width:
15 mm
286-721
Item no.: 286-723
Optocoupler module; Nominal input voltage: 24 VDC; Output voltage range: 15 … 30 VDC; Limiting
continuous current: 4 A; 3-wire connection/high-side switching; Red status indicator; Module width:
15 mm
286-723
Item no.: 286-725
Optocoupler module; Input AC/DC 10 V ... 30 V; Output DC 24 V/ 1 mA ... 0.5 A; negative switching
286-725
Item no.: 286-742
S0 interface power supply; Input voltage: 230 VAC; S0 interface
286-742
Item no.: 286-752
Optocoupler module; Nominal input voltage: 24 VDC; Output voltage range: 20 … 30 VDC; Limiting
continuous current: 0.5 A; 3-wire connection/high-side switching; Frequency: 25 kHz; Red status
indicator; Module width: 15 mm
286-752
Item no.: 286-752/002-000
Optocoupler module; Red status indicator
286-752
/002-000
Item no.: 286-790
Optocoupler module
286-790
Item no.: 286-791
Optocoupler module; Nominal input voltage: 24 VDC; Output voltage range: 20 … 60 VDC; Limiting
continuous current: 0.1 A; 2-wire connection; Frequency: 3 kHz; Red status indicator; Module width:
10 mm
286-791
Item no.: 286-792
Optocoupler module; Red status indicator
286-792
Item no.: 286-794
Optocoupler module; Nominal input voltage: 24 VDC; Output voltage range: 20 … 60 VDC; Limiting
continuous current: 0.1 A; 2-wire connection; Red status indicator; Module width: 10 mm
286-794
Item no.: 286-803
Component module with diode
286-803
280-816
01.05.2019Page /11 13
Page 12
Data sheet | Item number:280-816
Item no.: 286-805
Component module with diode
286-805
Item no.: 286-807
Component module with diode; with 7 pcs; Diode 1N4007; with common anode
286-807
Item no.: 286-809
Component module with diode
286-809
Item no.: 286-822
Component module with LED; Red LED; with common cathode
286-822
Item no.: 286-826
AND gate module with 6 inputs
286-826
Item no.: 286-830
Bridge rectifier module; Input voltage: 24 VAC; with varistor protective circuit
286-830
Item no.: 286-840
Bridge rectifier module; Input voltage: 250 VAC; with varistor protective circuit
286-840
Item no.: 286-890
Component module with fuse; for (5 x 20) mm microfuse; Nominal voltage: 24 VAC/DC
286-890
Item no.: 286-891
Component module with fuse; for (5 x 20) mm microfuse; Nominal voltage: 230 VAC/DC
286-891
Item no.: 286-895
Switching module; with changeover rocker switch; Switching voltage: 250 VAC; Switching current: 6
A
286-895
Item no.: 286-896
Switching module; Changeover; 1-pole; with momentary switch
286-896
assembling
Item no.: 209-106
Mounting carrier; for isolated mounting on DIN 35 rails
209-106
Item no.: 210-148
Angled support bracket; without screw
210-148
Protective Warning Marker
Item no.: 280-415
Protective warning marker; with high-voltage symbol, black; for 5 terminal blocks
280-415
Downloads
Documentation
Bid Text
280-816 doc
25.1 kB
Download
280-816
01.05.2019Page /12 13
Page 13
Data sheet | Item number:280-816
CAD/CAE - Smart Data
CAD data
3D Download 280-816 URL Download
280-816
Subject to changes.
01.05.2019Page /13 13
Loading...