AVT Jumpstarter 400
AVT Jumpstarter 700
Item #2594—400 Amp
Item #2595—700 Amp
User’s Manual
www.wagan.com
AVT™ Jumpstarter 400 & 700 by Wagan Tech
1
© 2011 Wagan Corporation
All Rights Reser ved
Wagan Tech and wagan.co m are trademarks used by Wagan Corpo ration
User’s Manual—Read before using this equipment
2
Thank you for purchasing the AVT™ Jumpstarter by Wagan Tech. With normal care and
proper treatment, it will provide years of reliable service.
Fully charge unit with the supplied 17 volt AC charger for a full 16 hours (#2594) or 20
hours (#2595) before using for the first time.
IMPORTANT!
Please read all of the operating instructions carefully prior to use. It is important to
understand all warnings, cautions and instructions included in this instruction manual, your
vehicle batter y manufacturer manual and other manuals for any device intended to be used
with this unit. Retain these instructions for future reference.
Safety Switch
Polarity Warning
Air Pressure Gauge
Battery Check/Air
Compressor Switch
Battery Level
Charging Jack
2.1A USB Power Ports (×2)
12V DC Socket
Light Switch
24 LED Work Light
Air Hose Compartment
Cautions
• This product is NOT a toy. Keep out of the reach of children.
• Never work alone with this product. Make sure that someone is available to give
assistance if needed.
• Do not operate this device while wearing vinyl clothing. Static electricity may be
generated when vinyl clothing is rubbed.
• Remove any metallic jewelry, such as rings, bracelets, necklaces and watches while
working with a lead acid batter y. It can produce a short-circuit that may cause
severe burns.
• Wear complete eye and clothing protection. Do not touch eyes while working near
or with battery.
• Keep battery terminals clean. Be careful to keep corrosion from coming in contact
with eyes.
• Do not operate this unit in or around water. Water can damage the unit.
• Do not let the cords of the jumpstarter or attached appliances get wet.
• This product is not intended for use in the rain or temperatures above 130°F.
• Never attempt to charge or jumpstart a frozen bat tery.
• To prevent short- circuits and arcing, never allow the metal ends/tips of clamps
(positive & negative terminals) to touch each other or connect to the same piece
of metal.
• Do not attempt to remove or replace the battery used in this device.
When the battery has reache d the end of its lifetime, take the entire unit to
a battery recycling facilit y.
• Use only the provided chargers, cables and clamps. Unauthorized par ts may
damage the unit.
• This product has no consumer serviceable parts.
• For proper and safe operation of the 12 volt DC power accessor y outlets,
do not place any thing into it except the plug of the accessory to be used.
Charging and Recharging
WARNING: Do not overcharge this unit. Overcharging may result in damage to the unit.
Prior to charging unit, read and understand all instructions for this unit.
• This product may arrive partially charged from the manufacturer. It is recommended
to fully charge the unit immediately after purchase and before first use.
• Fully charge unit with the supplied 17 volt AC charger for a full 16 hours (#2594) or
20 hours (#2595) before using for the first time.
www.wagan.com
AVT™ Jumpstarter 400 & 700 by Wagan Tech
3
© 2011 Wagan Corporation
All Rights Reser ved
Wagan Tech and wagan.co m are trademarks used by Wagan Corpo ration
User’s Manual—Read before using this equipment
4
• The charging LED indicator will illuminate while charging. The light will stay
lit while charging plug is plugged in. When charging is complete, press the
“Battery Check” but ton and the “Battery Status” light will show the state of the
battery charge. When charging is complete, remove the AC/DC adapter from the
unit. Press the battery status button and the green LED light will be illuminated to
indicate charging is complete.
• Do not charge the unit for more than 48 hours continuously.
• Do not charge the unit on a boat, boat ramp or dock since the electrical cords
and outlets used for charging could cause severe electrical shock if they get wet.
• It is recommended that the unit is in an upright position while charging.
Charging with AC Charger:
1. Insert AC charger plug into charging jack of the unit.
2. Insert AC charger receptacle plug into AC receptacle.
3. Fully charge the unit.
4. When charging is complete, unplug the AC charger receptacle plug, then the AC
charger from the charging jack on the unit.
Jumpstarting a Vehicle
WARNING: Vehicles equipped with onboard computers may be affected if the engine battery
is jumpstarted. Read your vehicle owner’s manual before attempting to start the vehicle to
determine if external starting assistance can be used. Failure to follow these instructions may
cause damage or explosion. Use safety glasses to protect eyes while jumpstarting a batter y.
USING THE UNIT AS A JUMPSTARTER WITH POWERFUL BATTERY 14V 7AH/14AH
This jumpstarter is equipped with a manual safety switch that only allows jumpstart energy
to flow when proper connections are made to battery and frame. Once the connections are
properly made, turn the safet y switch ON and you are ready to jumpstart the vehicle.
1. Turn off the vehicle ignition and all accessories (e.g. radios, lights, air conditioners
and cellular phones).
2. Set the emergency brake and put vehicles with automatic transmission in park
position.
3. Make sure Jumpstarter’s ON/OFF safety switch is turned to OFF.
4. Determine the polarit y of the vehicle’s battery terminals. The positive (POS, P,
+) battery terminal usually is larger in diameter than the negative (NEG, N, −)
terminal. If you are unsure, you should refer to the vehicle owner’s manual.
5. Determine whether your vehicle uses a negative or positive grounded system:
Negative ground system (negative battery terminal is grounded to chassis).
Most vehicles use this system. Positive grounded battery terminal is grounded to
chassis or any other part of the vehicle. IF YOU ARE UNSURE, YOU SHOULD REFER
TO VEHICLE OWNER’S MANUAL.
6. Remove clamps from the holders. Never allow clamps (positive & negative
terminals) to touch together or contact the same piece of metal to prevent shortcircuits and arcing.
7. Follow instructions for a negative grounded system or positive grounded system as
indicated below:
Negative Grounded System
a. Securely connect the positive (+) red clamp to the positive (POS, P, +) terminal
of the vehicle batter y or the remote positive (+) terminal if equipped.
b. Securely connect the negative (−) black clamp to the vehicle chassis, engine
block or a non-moving metal part of the vehicle which is verified to be
grounded. Do not clamp directly to negative battery terminal, carburetor,
fuel lines or sheet metal body parts.
c. See jumpstarting step 7 to continue.
Positive Grounded System:
a. Securely connect the negative (−) black clamp to the negative (Neg, N, −)
ungrounded terminal of the vehicle battery.
b. Securely connect the positive (+) red clamp to the vehicle chassis, engine block
or a non -moving metal part of the vehicle which is verified to be grounded. Do
not clamp directly to positive battery terminal, carburetor,
fuel lines or sheet metal body parts.
c. See jumpstarting step 7 to continue.
d. When clamps are connected with reverse polarit y, the reverse polarity
indicator is red and alarm sounds. Disconnect the clamps and connect
again properly.
e. When clamps are connected properly, turn ON the Jumpstarter’s safety switch.
7. Allow 1 to 2 minutes of charging time. It is recommended to have a second person
to assist holding the unit securely in place during the next steps.
8. Turn on the vehicle to attempt to start the engine. Stop if the vehicle does not start
after 4 to 5 seconds of engine cranking. Wait 3 to 4 minutes then try again. Repeat
several times until the vehicle star ts.
CAUTION: Excessive engine cranking can damage vehicle starter motor. If the
engine turns, but fails to start after several attempts, other technical problems might
be involved. Discontinue cranking the engine until the other problems have been
determined and corrected.
Loading...