WAFER GSM-KEY-ADC200 User Manual

WAFER GSM-KEY REMOTE CONTROL UNIT

http://www.waferstar.com

GSM-KEY-ADC200

MANUAL

ADC200 VERSION 5.0

SHANGHAI WAFER MICROELECTRONICS CO.,LTD

WAFER GSM-KEY REMOTE CONTROL UNIT

http://www.waferstar.com

GSM-KEY-ADC OPERATING INSTRUCTIONS

PRODUCT DESCRIPTION

WAFER GSM-KEY is an electronic board with an on-board GSM modem.The purpose of
this device is to open an electric gate by means of a GSM phone.It has a door open relay whose
contact has to be connected in parallel with the button which opens the gate. It has a White List of
regular user numbers who are enabled to open the phone, up to 200 and also it has up to 150
number for time zone. When the GSM-KEY receives a call, it will check to see if the calling
number is in the list. If it is in the list it will reject the call (so there will be no charge -at le ast with
today's charging procedures) and click the relay momentarily.

Also GSM-KEY has two alarm input port for the security detection including the intruder
detection alarm and gate problem alarm.

CONNECTOR DESCRIPTION

ADVANTAGES OF WAFER GSM-KEY

ˇ 200 Regular User Numbers memory.

ˇ SHL50+PHL50+QHL50 ,total 150 Special Numbers memor y for time zone.

ˇ 5 Alarm Numbers memory.

ˇ Up to 50 logs stored in database.

ˇ No call charges to operate.

ˇ No line rental using ‘Pay as You Go’.

ˇ No key-fobs for children to lose.

ˇ Let visitors and deliveries in remotely.

ˇ Impossible to clone or intercept.

ˇ Caller ID confirmation for security.

ˇ Quick & easy number barring.

ˇ Easy programming in minutes with your phone or PC software.

1. GSM LED (From Left)

2. MCU LED

3. RELAY LED

4. GSM Connected LED

WAFER GSM-KEY REMOTE CONTROL UNIT

http://www.waferstar.com

INSTALLATION

To install the GSM-KEY, you need to connect the 2 wires of the relay contact in parallel with
the gate opening button. The relay contacts can stand 48V 0.5A maximum, this is enough for its
operation but don't try to switch higher voltages or currents. You should install the GSM-KEY
in a place where there is GSM signal coming from the operator you want to use. Check it with a
phone before proceeding with the installation. If you need to install the device in a place with little
signal, you may consider using an external antenna that we may supply as an option to be
purchased separately with 50cm cable.

You should then insert the SIM Card of the operator you want to use with the right direction
according to the following pictures.

!Note! : That would be better to test the SIM card in your mobile phone to ensure that
SIM Card is working before inserting it in the unit.

GSM-KEY also comes with additional 2 Input.The inputs can be used to generate alarms
when triggered.For examples,you can can connect the saftey beam output to the GSM-KEY
Alarm1 and Alarm2 input.

Please read this entire manual before installation !Note!

z Take EXTREME care with the Voltage Power supply at AC/DC12-24V

z Mustn’t suppy the 110V or 220V to this device,that would damage all board !

z If device is connect into electricity, you should take off its cover carefully.
z To maximise reception, install the GSM antenna in a prominent elevated position

if possible, and vertically mounted.

z The GSM unit requires mounting carefully in a weatherproof enclosure for out

door operation.

z Always ensure that the power is switched OFF before inserting or removing a SIM

card from its holder or damage will be caused to the module.

1.Slide back the SIM door and
lift it up

2.Slide the SIM Card into the
SIM door making sure that
the clipped corner of the SIM
card lines up with the clipped
corner of the SIM holder

3.Close the SIM door

4.Slide the SIM door to lock the
SIM card in place

WAFER GSM-KEY REMOTE CONTROL UNIT

http://www.waferstar.com

WAFER GSM-KEY PROGRAMMING

You also can program the GSM-KEY with SMS commands using your phone. It is safe to do
so because in addition to the fact that other people may not know the number of the SIM inserted
in it, we also use a Password that makes it impossible for anybody who doesn't know it to access
the system by chance.

Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap
etc. Don't add spaces or any other character.

Some complicated Instructions,that cann’t be programmed by the phone SMS. That would
need to use the PC software to program and inquire the status of the terminal.

The bellow wire picture is to show how to connect the cable to the PC program connector
with the Program adapter.Please connect it in the right direction with the picture.

GSM-KEY PC Program Software interface

1. Setting and Log page switch

2. Open saved file

3. Save units phone numbers in your computer for future changes

4. Save in a new file name

5. Communitcaton selection ,Com port configuration

6. Connect to the unit

7. Select Language

8. Setting Tab – Insert regular/Special phone numbers,miscellane ous

Fast Teach Button:

On the board version of GSM-KEY-ADC, there is a “ Fast Learn Button”.
When you want to do the fast program to program your number to the WHL list to GSM-KEY device, you
can press the button until the LED light, then use your phone to dial the number of GSM-KEY, when pickup
the calling,the Teach LED would flash,reject the calling and save the phone number into the device.

WAFER GSM-KEY REMOTE CONTROL UNIT

http://www.waferstar.com

9. Log Tab

10. Phone numbers Tab – Add regular phone numbers 200

11. Special phone numbers Tab – Add special phone numbers 750

12. Alarm Phone numbers Tab – Add alarm phone numbers 5

13. Miscellaneous Tab

The following compand is used in the GSM-KEY :

#PWD: Password

#CAP: Change password

#WHL: White List (add or remove numbers)

#GOT: Gate pulse time

#ALARM: Alarm information setting

#MODE: Relay mode

#CSQ: Check Signal Quality

#SCA: Set service center address

#STATUS: Check status

#OUT: Use the SMS to control the switch to ON or OFF

Once you issue a command with an SMS, you will receive a confirmation SMS with OK
if everything is correct or Err if there is an Error.

GSM-KEY SMS COMMAND LIST:

#PWD Password.

This command must always come first 6 digits as a password.
The standard default one, when the device comes from the factory, is 123456.
We suggest that you change it, using the #CAP command.
In all the following examples we will use 123456 as an example of password.

#CAP Change Password.

Use this command to change the password with a new one that you will chose for your device
( don't forget it or you will have to send the unit back to us to reset it, and this has a cost )
The #CAP command must be issued 2 times to be sure you don't digit a wrong one.
OF course it must be preceded by the old password.
For example, to change the password 123456 into the new password 333444 you need to send the
following SMS:

#PWD123456#CAP333444#CAP333444

Acknowledge SMS: PWD SETUP OK
If you wrote correctly, or an Error message if you made a mistake.
If the old password is error,then conformation would be : Error Old Password
If you input two different new password,then reply would be : Error New Password,Please Check the

input again