WAFER GSM-HOUSE Operating Instructions Manual

WAFER GSM-HOUSE INTERCOM UNIT

http://www.waferstar.com

GSM-HOUSE MANUAL

New version published from 2016

SHANGHAI WAFER MICROELECTRONICS CO.,LTD

WAFER GSM-HOUSE INTERCOM UNIT

http://www.waferstar.com

GSM-HOUSE OPERATING INSTRUCTIONS

PRODUCT DESCRIPTION

WAFER GSM-HOUSE is an anti-vandal GSM intercom with self contained GSM door entry
audio intercom system and also built-in the WAFER “GSM-KEY” function,that is used to open
an electric gate by means of a GSM phone.

For the GSM intercom function.By pressing the Call buton on the GSM-HOUSE,it makes a
voice connection in a few seconds,allowing two way audio communication between the visitor
and owner.Up to two numbers can be called in sequence.Door release is from the phone keypad
during an intercom call. This allows the owner to answer intercom calls at anytime,from anywhere,
even when not at home.The unit does not need any special installation or complicated wiring, it
fixes to a wall or post and then only needs power supply and an active SIM card.

For the “GSM-KEY” function,It has the door open relay whose contact has to be connected in
parallel with the button which opens the gate. It has a White List of numbers who are enabled to
open the phone, up to 200. When the GSM-HOUSE receives a call, it will check to see if the
calling number is in the list. If it is in the list it will reject the call (so there will be no charge -at
least with today's charging procedures) and click the relay momentarily.

Also GSM-HOUSE has two alarm input port for the security detection including the intruder
detection alarm and gate problem alarm.GSM-HOUSE also has the recharageable backup battery
inside for power off alarm and keep working even for sereral days.

CONNECTOR DESCRIPTION

WAFER GSM-HOUSE INTERCOM UNIT

http://www.waferstar.com

ADVANTAGES OF WAFER GSM-HOUSE

ˇ Wireless intercom with one push button.

ˇ 2 phone number can be assigned to the push button for intercom voice calling.

ˇ Wide power voltage input from DC9V to DC18V

ˇ Gate control function by authorized WHL numbers

ˇ 200 Number memory can be authorised.

ˇ The output can be activated by pushing the unit’s call button.

ˇ No call charges to operate when phone calling to control.

ˇ Open gates prior to arriving.

ˇ Let visitors and deliveries in remotely.

ˇ Impossible to clone or intercept.

ˇ Caller ID confirmation for security.

ˇ Quick & easy number barring.

ˇ Can be operated from anywhere.

ˇ Easy programming in minutes with your phone or PC software

ˇ Remote configuration by SMS message.

ˇ Recharageable backup battery for power off alarm and working.

INSTALLATION

To install the GSM-HOUSE, you need to connect the 2 wires of the relay contact in parallel
with the gate opening button. The relay contacts can stand 30V 2A maximum, this is enough for
its operation but don't try to switch higher voltages or currents. You should install the
GSM-HOUSE in a place where there is GSM signal coming from the operator you want to use.
Check it with a phone before proceeding with the installation. If you need to install the device in a
place with little signal, you may consider using the magnetic mount better gain GSM antenna that
we may supply as an option to be purchased separately with 200cm cable.

You should then insert the SIM Card of the operator you want to use with the right direction
according to the following pictures.

!Note! : You must remove the PIN request from the SIM before inserting it in the
unit, otherwise the device will not work. In order to do so, insert the SIM in a mobile phone and

Please read this entire manual before installation !Note!

z Take EXTREME care with the DC voltage polarity Power line installation
z In case of fault power connection will cause the default permanently.
z If device is connect into electricity, you couldn’t take off its cover.
z To maximise reception, install the GSM antenna in a prominent elevated position if

possible, and vertically mounted.

z The GSM unit requires mounting carefully with the lock for proper operation.

z Always ensure that the power is switched OFF before inserting or removing a SIM

car

d

from its holder or damage will be caused to the module.

WAFER GSM-HOUSE INTERCOM UNIT

http://www.waferstar.com

verify the SIM card to call other phone and send and receive the SMS).

Lock the SIM card in the right direction:

GSM-HOUSE also comes with additional 2 Input.The inputs can be used to generate alarms
when triggered. For examples,you can can connect the door or gate saftey beam output to the
GSM-HOUSE Alarm1 and Alarm2 input.

Before the following test and programming,connect the DC12V properly to the DC12VIN
and GND.

After the device successfully connected to the GSM net,the LED on the Call button would
flash around 5 seconds per time.then we can start the following test:

WAFER GSM-HOUSE PROGRAMMING

You can program the GSM-HOUSE with SMS commands using your phone. It is safe to do
so because in addition to the fact that other people may not know the number of the SIM inserted
in it, we also use a Password that makes it impossible for anybody who doesn't know it to access
the system by chance.

Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap
etc. Don't add spaces or any other character.

Some complicated Instructions,that cann’t be programmed by the phone SMS. That would
need to use the PC software to program and inquire the status of the terminal.

1.Slide back the SIM door and
lift it up

2.Slide the SIM Card into the
SIM door making sure that
the clipped corner of the SIM
card lines up with the clipped
corner of the SIM holder

3.Close the SIM door

4.Slide the SIM door to lock the
SIM card in place