Page 1
Page 1 of 4
4
5
4
1
Sofa Seat
x1
2
Left Arm
x1
3
Right Arm
x1
4
Sofa Leg
x4
5
Support Leg
x1
6
Sofa Back
x1
7
Back Cushion
x2
8
Side Cushion
x2
SOFA
LOVESEAT /SOFA
Thank you for purchasing the LOVESEAT/SOFA！
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the sofa, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 40 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
LOVESEAT
-WITHOUT
SUPPORT
LEG
Hardware:
A
B
Short Bolt M8x25mm x12
Long Bolt M8x50mm x2
Component:
C
D
6
2
7
8
1
7
Flat Washer M8 x14
Allen Wrench M5 x1
8
3
Page 2
Page 2 of 4
Zipper
1
Back
2
3
1
Sofa Back
Sofa Front
LOVESEAT /SOFA
STEP 1:
Put Sofa Seat (1) upside down on a carpeted or padded surface.
Open the Zipper on the bottom of Sofa Seat (1) as shown.
Please find Sofa Legs (4), Support Leg (5), Back Cushions (7), Side Cushion (8), and Hardware package from inside of
Sofa Seat (1).
4 x Sofa Legs (4) + 1 x Support Leg (5) + 2 x Back Cushion (7) + 2 x Side Cushion (8) + Hardware Package
STEP 2:
Please carefully turn over Sofa Seat (1).
Insert Left Arm (2) and Right Arm (3) to Sofa Seat (1) by using the pre-installed Clips on Sofa Seat (1), Left Arm (2), and
Right Arm (3) to lock each other as shown.
Page 3
Page 3 of 4
Bx2
Cx2
Dx1
2
3
1
C
B D
C
B
A
C
4
2
4
A
C
D
D
A
C
4
3
4
A
C
D
D
1
5
LOVESEAT /SOFA
STEP 3:
Put the assembled Sofa Seat (1), Left Arm (2), and Right Arm (3) backside down on a carpeted or padded surface.
Insert 2 pieces of Long Bolt (B) with 2 pieces of Flat Washer (C) into the pre-drilled holes on Left Arm (2)/Right Arm (3)
through the pre-drilled holes on inner side of the bottom of Sofa Seat (1) as shown.
Use Allen Wrench (D) to tighten Long Bolts (B) clockwise until secure.
STEP 4:
Please carefully close the Zipper on the bottom of Sofa Seat (1).
Put the assembled Sofa Seat (1), Left Arm (2), and Right Arm (3) upside down on a carpeted or padded surface.
Place 1 piece of Sofa Leg (4) into the bottom of Sofa Seat (1) as shown.
Insert 3 pieces of Short Bolts (A) with 3 pieces of Flat Washers (C) into the pre-drilled holes on the bottom of Sofa Seat (1)
through the pre-drilled holes on the metal plate of Sofa Leg (4) as shown.
Use Allen Wrench (D) to tighten Short Bolts (A) clockwise until secure.
Repeat the same steps for the remaining 3 pieces of Sofa Leg (4).
Tighten Support Leg (5) into the middle of the bottom of Sofa Seat (4) until secure by hand.
Hardware & Tools required
Hardware & Tools required
Page 4
LOVESEAT /SOFA
Page 4 of 4
7
7
8
8
2
3
1
4
5
4
6
2
3
1
5
4
4
STEP 5:
Place Sofa Back (6) to the assembled Sofa Seat (1), Left Arm (2), and Right Arm (3) as shown.
Insert Sofa Back (6) to Left Arm (2) and Right Arm (3) by using the pre-installed Clips on Left Arm (2), Right Arm (3), and
Sofa Back (6) to lock each other as shown.
Carefully cover the fabric on the back of Sofa Back (6) by using pre-installed Velcro
STEP 6:
Carefully put 2 pieces of Back Cushion (7) and 2 pieces of Side Cushion (8) to the assembled Sofa Seat (1), Left Arm (2),
Right Arm (3), and Sofa Back (6) as shown.
Assembly is complete. Your sofa is ready to be used now!
Loading...