Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Wire Connectors
B
x6
Safety Clip
C
x7
Ceiling Canopy
D
x1
F
Shade
x7
Crossbar Assembly
A
x1
Jumper Wires
E
x2
STEP 1 - Installing the CrossbarAssembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Figure 1
Outlet Box
A
Outlet Box Screws
(not included)
STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Remove mounting balls from the Crossbar Assembly (A). Fit the
eiling Canopy to the
C (D) Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug
against the and the mounting balls. If
of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
ceiling
Ceiling Canopy (D)
Supply Wires with
Ground Wire
not, adjust the length
White Wire
Black Wire
Green Wire
(Step 2 Continued)
achieved. Once the Ceiling Canopy (D) is secure, remove the
mounting ball and Ceiling Canopy (D) and proceed to Step 3.
A
Mounting Screw
D
Mounting Ball
Please measure the height you want to hang the pendant prior
to hanging so you know what length to cut the wire. You can add
6" to that length to help adjust the shades up or down once it’s
hung. Please note, all the extra wire will not fit inside the small
canopy and junction box, the wire needs to be cut at the desired
length to fit inside the canopy and junction box to then help
adjust to the exact height.
IMPORTANT: Install the cord into the ceiling canopy before
cutting it to length.
Lock Rod
G
x21
Fixture Body
Hex Nut and
Lock Washer
H
x7
Figure 2
1of3
STEP 3 - Install Fixture Bodies to Ceiling Canopy
A. Loosen set screws located on the couplings that are mounted to the
underside of the Ceiling Canopy (D). Do not remove set screws
completely.
B. Thread pendant cord through the coupling mounted to the underside
of the Ceiling Canopy (D). Adjust cord to the desired length then
tighten set screw to hold pendant length in place.
C. Install Safety Clips (C) onto the pendant cords by threading the cord
through one hole then back through the second. Slide Safety Clips
(C) to approximate 2” from canopy.
D. Repeat these steps for all pendants.
E. After the ceiling canopy is installed to the junction box, a final
adjustment can be made to get the pendants to hang at the desired
height by loosening the set screws on the coupling slightly then re-
tighten when the pendants are adjusted to the desired height.
C
D
Set Screw
Coupling
Cord
H
Figure 3
STEP 4 - Connections Fixture Wires to Jumper Wires
A. Strip back the clear wire covering on the 3 pendant cords to expose
the black, white and green wire. Leave at least approximately 3" of
cord length inside of the ceiling canopy. Strip each end of 3 fixture
wires.
B. Use supplied wire connectors (B) to connect fixture wires to Jumper
Wires (E). Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape.
C. There are two sets up jumpers that have to be wired to the pendant
wires. The first set of jumpers will use the wires from 4 pendants.
The second set of jumpers will use the remaining wires from 3
pendants. Follow the illustrations below for correct wiring.
(1) White
Jumper Wire
(1) Black
Jumper Wire
(1) Green
Jumper Wire
(1) White
Jumper Wire
(1) Black
Jumper Wire
(1) Green
Jumper Wire
Figure 4
B
WIRINGFOR4SETSOFWIRES
B
WIRINGFOR3SETSOFWIRES
(4) White wires
from fixture
(4) Black wires
from fixture
(4) Ground wires
from fixture
(3) White wires
from fixture
(1) White Jumper Wire
(3) Black wires
from fixture
(1) Black Jumper Wire
(3) Ground wires
from fixture
(1) Green Jumper Wire
STEP 5 - Attach the Lanyard
A. The purpose of the lanyard is to provide a means to support the
fixture hands free from the junction box while connecting the
electrical wires.
B. Turn the Button Stop so it may be inserted into a Crossbar slot.
Make sure the Button Stop is completely inside the Crossbar. Slowly
release the fixture to make sure it
is supported by the Button Stop.
Proceed to the wiring steps in the
next step. Once you are
complete with the wiring, the
Lanyard will push
into the junction
box when the
fixture is placed for
final mounting.
Figure 5
STEP 6 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare,orGreen
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
Button Stop
D
Figure 6
Slot
White Jumper Wire
Black Jumper Wire
Ground wire
from Ceiling Canopy
Green Jumper Wire
Crossbar
Lanyard
2of3
STEP 7 Install Ceiling Canopy-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (D) over the outlet box. Align the holes in the ceiling canopy
with the mounting screws, then attach the Ceiling Canopy (D) using
the previously removed mounting balls. Hand tighten until snug.
A
Mounting Screw
D
Mounting Ball
Figure 7
STEP 8 - Install Shades and Bulbs
A. Place the Shade (F) over the socket and align holes on the side of
the Shade (F) to bolts on the side of the Fixture Body (H). Place
Lock Rods (G) through holes on the side of the Shade (F) and
thread them onto bolts. Hand tighten until snug.
B. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
FINISH: EAR
TH BLACK
14” Dia.
103.5”
Bolt
F
Figure 8
H
Socket
G
T10 Vintage Bulb
(recommended
but not included)
12.75”
9.75”
18.75” Dia.
BOTTOM VIEW
7.75” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO
THE NEAREST 1/4"
3of3
Loading...