Label Picture Description QTY
D Seat 1
E Long Leg 2
F Short Leg 2
Label Picture Description QTY
①
Bolt (M6*15MM) 11
②
Bolt (M6*55MM) 9
Caution : You must read this before you proceed
Bench
Page 1 OF 5
③
Washer 9
④
Allen Key 1
Overview
This Bench has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Bench parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Before
Beginning
Assembly:
FRONT FACING
Short Leg(F)
Long Leg(E)
Seat(D)
Page 2 OF 5
Step 1
Step 2
Open the carton and place all the parts onto a clean, non-marring surface.
Place the Seat(D) facedown.
Step1.1: Attach Seat(D) to Long Leg(E) using Bolts(①) with Allen Key(④) as shown above.
Step1.2: Attach Seat(D) to Short Leg(F) using Bolts(①)with Allen Key(④) as shown above.
Step1.3: Attach Long Leg(E) to Short Leg(F) using Bolts(②)and Washer(③) with Allen Key(④) as
shown above.
Do not fully tighten the Bolts.
Step2.1:Attach Seat(D) to Long Leg(E) using Bolts(①) with Allen Key(④) as shown above.
Step2.2:Attach Long Leg(E) to Short Leg(F) using Bolts(②)and Washer(③) with Allen Key(④) as
shown above.
Do not fully tighten the Bolts.
D
setp1.1
①
④
setp1.2
E
D
E
F
④
①
D
E
F
setp1.3
③
②
④
setp2.1
setp2.2
E
D
D
E
F
①
④
③
②
④
F
Page 3 OF 5
Step 3
Step 4
Stand the Bench up.
Place the Bench on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully sit onto the Bench
This will help to align all parts at all joints.Then get off the Bench, and in a sequential manner,
proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute this same process.
Note: This step is done best with the assistance of a second adult.
Your Bench is ready for use.
This Bench can only be used on a flat, level surface.
Step3.1:Attach Seat(D) to Short Leg(F) using Bolts(①) with Allen Key(④) as shown above.
Step3.2:Attach Long Leg(E) to Short Leg(F) using Bolts(②)and Washer(③) with Allen Key(④) as
shown above.
Step3.3:Attach Long Leg(E) to Short Leg(F) using Bolts(②)and Washer(③) with Allen Key(④) as
shown above.
Do not fully tighten the Bolts.
D
setp3.1
①
④
setp3.
E
D
F
E
D
E
F
setp3.3
F
③
②
④
③
④
Page 4 OF 5
Page 5 OF 5
Label Picture Description QTY
A Wooden Countertops 1
B Long Leg 2
C Short Leg 2
Label Picture Description QTY
①
Bolt (M6*15MM) 13
②
Bolt (M6*55MM) 9
③
Washer 9
④
Allen Key 1
Caution : You must read this before you proceed
Table
Page 1 OF 5
Before
Beginning
Assembly:
Overview
This Table has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of theTable parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
FRONT FACING
Short Leg（
C
）
Long Leg（
B
）
Wooden Countertops（
A
）
Page 2 OF 5
Step 1
Step 2
Open the carton and place all the parts onto a clean, non-marring surface.
Place the Wooden Countertops(A) facedown.
Step1.1:Attach Wooden Countertops(A) to Long Leg(B) using Bolts(①) with Allen Key(④) as
shown above.
Step1.2:Attach Wooden Countertops(A) to Short Leg(C) using Bolts(①)with Allen Key(④) as
shown above.
Step1.3:Attach Long Leg(B) to Short Leg(C) using Bolts(②)and washer(③) with Allen
Key(④) as shown above.
Do not fully tighten the Bolts.
Step2.1:Attach Wooden Countertops(A) to Long Leg(B) using Bolts(①) with Allen Key(④) as
shown above.
Step2.2:Attach Long Leg(B) to Short Leg(C) using Bolts(②)and Washer(③) with Allen
Key(④) as shown above.
Do not fully tighten the Bolts.
A
setp1.1
①
④
setp1.2
B
setp2.1
setp2.2
A
B
C
④
①
A
B
C
setp1.3
③
②
④
B
A
C
①
④
A
B
C
③
②
④
Page 3 OF 5
Step 3
Step 4
Stand theTable up.
Place the Table on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
This will help to align all parts at all joints.Then get off the Table, and in a sequential manner,
proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute this same process.
Note: This step is done best with the assistance of a second adult.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Step3.1:Attach Wooden Countertops(A) to Short Leg(c) using Bolts(①) with Allen Key(④) as
shown above.
Step3.2:Attach Long Leg(B) to Short Leg(c) using Bolts(②)and Washer(③) with Allen
Key(④) as shown above.
Step3.3:Attach Long Leg(B) to Short Leg(c) using Bolts(②)and Washer(③) with Allen
Key(④) as shown above.
Do not fully tighten the Bolts.
A
setp3.1
①
④
setp3.2
B
A
C
BAB
C
setp3.3
C
③
②
④
③
②
④
Page 4 OF 5
Page 5 OF 5
Loading...