Page 1
Installation Guide
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsare missingordamaged, donot attempttoassemble, install,or operatethefixture. MissingParts? Contactyouroriginal placeof
purchase.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)B10Candelabra Basebulbs 60WMaximum,bulb notincluded.
30-45minutes
Identifyandinspect allparts beforebeginninginstallation. Checkpackage contentlistand diagramsbelow toensureall partsare
Package Contents
Glass
D
x1
Shade
C
Crossbar Assembly
A
x1
Fixture Body
B
x1
STEP 1 Installing the CrossbarAssembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug.
Outlet Box Screws
(not included)
STEP 2 Test Fit the Backplate to the
Crossbar Assembly
A. Remove the mounting balls from the
-
Crossbar Assembly (A). Place the
backplate and Fixture Body (B) onto
the Crossbar Assembly (A) and secure
with mounting balls. Note: The
backplate and Fixture Body (B) should
be snug against the wall and held tight
with the mounting balls. If it is not,
adjust the length of the mounting
screws on the Crossbar Assembly (A)
by unscrewing the preassembled hex
nut and lock washer and then screwing
the mounting screws in or out of the
crossbar until the correct length is
achieved. Once the backplate and
Fixture Body (B) is secure, remove the
mounting ball and Fixture Body (B) and
proceed to Step 3.
x1
Stem
E
x1
Finial
F
x1
Outlet Box
A
Supply Wires with
Ground Wire
Mounting Screw
A
Hex Nut and
Lock Washer
Figure 1
Backplate
Mounting
Ball
STEP 3 - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
Figure 3
STEP 4 - Install Shade, Glass and Bulb
a. Thread the stem (E) onto the coupling
on fixture. Hand-tighten until snug.
b. Place Glass (D) over the stem (E),
Secure with the Finial (F), Handtighten until snug.
c. Place the shade (C) over the candle
cover.
d. Insert bulbs onto sockets and screw
snugly into place.
Your fixture is now assembled and
ready to use. Enjoy!
FINISH: POLISHED NICKEL
NOTE: ALL DIMENSIONS ARE
ROUNDED UP TO THE NEAREST 1/4"
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
26.5"
Green Ground Screw
on the Crossbar
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Bulb
(not included)
C
candle cover
B
Figure 4
E
D
F
8”
5"
9”
6"
1of1
Loading...