ASSEMBLY AND INSTALLATION
INSTRUCTIONS
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Parts:
Mounting Strap (A)
Lock Nut (B)
12”Rod (X3)(J)
Mounting Screw (D)
Nipple (C)
6”Rod (K)
Wire Nut (E)
Green Grounding
Screw (F)
Coupling Kit (G)
Collar (H)
Canopy (I)
3”Rod (L)
Outlet Box
House Grounding Wire
Wire Nut (E)
Fixture Grounding Wire
Lock Nut (B)
Mounting Strap (A)
Green Grounding Screw (F)
Mounting Screw (D)
Nipple (C)
Lock Nut (B)
Canopy (I)
Collar (H)
Fixture Wire
Coupling Kit (G)
Set Screw-1 (X3)(M)
Interior Glass (P)
Set Screw-2 (X3)(N)
Exterior Glass (O)
1. Rod Connections:
a. Thread the fixture wire from the socket through the support
and lower rods, then secure the lower rod onto socket using
the threaded pipe.
b. Thread the fixture wire through the threaded pipe and middle
rod, and then secure the middle rod onto the lower rod using
the threaded pipe.
c. Thread the fixture wire through the threaded pipe and upper
rod, and then secure the upper rod onto the middle rod using
the threaded pipe.
The height can be adjustable to 19-1/2"~58-1/2", by using
the rods.
2. Thread the fixture wire through the coupling kit, collar, canopy,
then secure the rod assembly to the coupling kit.
3. Thread the fixture wire through the nipple, lock nut and mounting
strap. Install the lock nut onto one end of the nipple leaving about
3/8” (10mm) thread exposed. Install same end of nipple by
screwing into coupling kit, secure nipple by tightening lock nut.
Upper Rod
Threaded Pipe
Middle Rod
Threaded Pipe
Lower Rod
Support
Threaded Pipe
Socket
Set Screw-1 (O)
Interior Glass (P)
Set Screw-2 (N)
Metal Ring
Exterior Glass (O)
Bulb T10 Max.75W
(not included)
4. Attach the nipple to the mounting strap, then secure it with lock nut.
5. Attach the mounting strap to outlet box by using two mounting screws.
6. Pull out the outlet wires and the house grounding wire from the outlet box.
Make wire connections by
using the wire nuts:
---The black (hot) wire from fixture to the black (hot) wire from power source.
---The white (neutral) wire from fixture to the white (neutral) wire from power
source.
---Attach the fixture grounding wire to the mounting strap with the green
grounding screw. Then connect it to the house grounding wire with the
wire nut.
Carefully put the wires back into the outlet box.
7. Attach the canopy to the mounting strap, and secure it with collar.
8. Hold the socket into the interior glass shade, thread the three set screws-1
through each holes of interior glass shades, and then secure them into the
support.
9. Place the interior glass shade into the center of exterior
glass shade and metal ring, then thread the three set
screws-2 through each holes of metal ring and exterior
Fig. 2
Support Brace
glass shades, secure them into the set screws-1.
10. Pushing up the glass shade, make the socket to show
outside the glass shade. Install a bulb (not included).
See relamping label at socket area or packaging for
maximum allowed wattage. (See Fig. 1)
11. Turn on the power at the main fuse or circuit breaker box.
12. Angled mounting recommended for a vaulted or
angled ceiling. (See Fig. 2)
Fig. 1
Glass Shade
Scoket
Bulb
Outlet Box
Canopy
Coupling Kit
A
B
A: 4-1/2"
B: 19-1/2" ~ 58-1/2"
Loading...