Assembly Instructions
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
EASY
DIFFICULT
Page 1 of 5
Tools Required for Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
(Not Included)
Wrench
(Not Included)
Page 2 of 5
MD
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
Parts List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
#4 x 1 pc x 2
Front Leg Support
Hardware List
#A x 4 pcs x 2
Bolt 1/4”x3-1/4”
#B x 3 pcs x 2
Bolt 1/4”x1-1/2”
#C x 4 pcs x 2
Hex Nut
#D x 11 pcs x 2
Flat W asher
#5 x 2 pcs x 2
Side Leg Support
Note: The above parts and hardware are
shown for a complete assembly of ONE
chair . However, the actual parts and
hardware (with an exception of the wrench
and Allen wrench) in the box will be twice
the quantities listed to include the
assembly of the second chair.
#E x 11 pcs x 2
Lock W asher
#F x 1 pc
Allen Wrench
#G x 6 pcs x 2
Screw M4x38mm
#H x 1 pc
Wrench
Page 3 of 5
#B x 3 pcs
#D x 3 pcs
#E x 3 pcs
I. Place the backrest with legs (#1) on a protected surface.
II. Align the seat (#2) with the pre-drilled holes of the backrest with
legs (#1).
III. Prepare 3 bolt assemblies by inserting FIRST the lock washer
(#E) onto the bolt (#B) and then the flat washer (#D) onto the
SAME bolt (#B), in that order.
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
II. Insert the bolt assemblies through the pre-drilled holes on the
#A x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
(#E) onto the bolt (#A) and then the flat washer (#D) onto the
SAME bolt (#A), in that order.
corners the seat (#2) and secure those bolts using the Allen
wrench (#F) to lock them with the backrest with legs (#1).
Page 4 of 5
Turn right (clockwise) to tighten
I. Insert the front leg support
(#4) between the 2 front legs
(#3). Then insert the 2 side
leg supports (#5) into the
backrest with legs (#1) and
the 2 front legs (#3).
II. Align the 2 front legs (#3)
with the pre-drilled holes of
the seat (#2).
III. Insert FIRST the flat washer
(#D) onto the threaded stud
of the front legs (#3) and then
the lock washer (#E) onto the
SAME stud, in that order.
Secure the hex nut (#C) onto
the same stud using the
wrench (#H) to tighten the
parts together .
#C x 4 pcs
#D x 4 pcs
#E x 4 pcs
Turn right (clockwise) to tighten
#G x 6 pcs
I. Secure the front leg support
(#4) and the 2 side leg
supports (#5) with 6 screws
(#G) using a Phillips
screwdriver to lock them with
the backrest with legs (#1)
and the 2 front legs (#3).
II. Carefully turn the completed
chair upright. Make sure the
chair is rested on a flat
surface and does not feel
loose or wobbly. If it does,
double check that the
bolts/screws are secured and
properly tightened.
#4
Turn right (clockwise) to tighten
#5
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR.
Page 5 of 5
Loading...