WAC Lighting WTK-1014, WTK-1023, WTK-1035, WTK-1052, WHK-1035 Installation Instruction

INSTALLATION INSTRUCTION

Exterminator II LED Track Luminaires

WTK-1014/1023/1035/1052, WHK-1035/1023/1052

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

Overview:

Fixtures are designed for use on WAC Lighting’s track systems. They may also be used on other manufacturer’s brand of track
(consult factory for compatibility).

LED TRACK LUMINAIRE TRACK SYSTEM

WTK-1014/WTK-1023/WTK-1035/WTK-1052 Series WTK 120V W Track

WHK-1035/WHK-1023/WHK-1052 Series WHK 277V W Track

Installing on Track

1. Turn the lock switch to the unlock position. Turn the circuit selecting handle to the power o position. (Fig 1)

Fig 1

W Track

Adapter

Switch handle
(power o position)

Lock switch
(unlock position)

2. Make sure the convexity on the adaptor box is at the same side with the slot on the track (Fig 2).
Fit the adaptor box into the track. Ensure the convexity on the adaptor box is at the same side with the slot on the track.

Fig 2

Slot

Convexity

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2016 1

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

Exterminator II LED Track Luminaires

WTK-1014/1035/1052, WHK-1035/1052

Installing on Track (Continue)

3. Turn the lock switch to the lock position. Turn the circuit selecting handle to 1 or 2 to switch the power on.

Fig 3

View A

Lock switch
(lock position)

View A

FIXTURE POSITIONING:

4. Rotate the luminaire’s body horizontally or vertically to aim it properly.
The xture can rotate ±90°vertically and 360 °horizontally.

Fig.4

360°

±90°

ACCESSORIES (Fig.5)

1. Use a screw-driver loosen the two screws at the back of the xture body.

2. Take out the front frame, then change the lens.

3. To install cross louver or snoot, use the clips around the front frame to fasten them directly.

1

Circuit selecting handle

1. Power on at circuit 1

2. Power on at circuit 2

2

Fig.5

Snoot

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2016 2

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Screw

Lens

Front Frame

Cross Louver

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

Exterminator II LED Track Luminaires

WTK-1014/1035/1052, WHK-1035/1052

Aligning the Reector (Fig. 6)
Before putting the accessory assembly back to the xture, make sure to align the reector properly as shown in Fig. 6.

Fig. 6

1014HS 1023HS

Reector

Two legs of reector
must be kept in position

LED holder

Reector Holder

Lock the reector
with the holder by
matching the notches

1035HS

Two legs of the reector
must be inserted into the
matched holes of LED chip

LED chip with two holes for
reector to x a position

1052HS

Fix the reector on
the LED holder by
twisting clockwise

LED holder

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2016 3

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]