WAC Lighting WAC5794 Installation & Assembly

INSTALLATION INSTRUCTION

1” LEDme Mini Recessed - New Construction

HR-LED231R, HR-LED232R, HR-271R, HR-272R

SAFETY INSTRUCTION

To reduce the risk of re, electrical shock and injuries to persons:

• Turn o power at main switch prior to installation.

• Use only with Class 2 Power supplies unit.

• Contact Manufacturer for LED replacement.

• Contact customer service ,better to use the recommended Class 2
power supplies unit.

MOUNTING AND WIRING:

1. Cut a 2 1/4” diameter hole on the ceiling.

2. Feed the xture wires through the hole, and connect to wires from
the Power Supply with connector.

3. Compress the springs on either side of the xture and insert into the
ceiling until the trim ring is ush to the ceiling.

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

LEDme® Class 2 Electronic Drivers

LD-700MA03-EDIM-IS

SAFETY INSTRUCTION

To reduce the risk of re, electric shock or injury to persons:

• Always turn o power at main switch prior to installation.

• System intended for installation by a qualied electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.

• For use with LED loads.

Model LD-700MA03-EDIM-IS

Input Voltage 120V ac,60Hz

Input Current Max 0.04A

OUTPUT CURRENT 700mA

Port Output Voltage 2-4V DC

Port Load 1PC 1x3W LED Fixtures

Port Load Lead Wires 12-22AWG

Output Port 1 PCS

FEATURES:

• 700mA constant current for LED’s optimized and stable performance.

• Capable of supplying power to a single LED xture.

• Special circuit design to protect LED from high voltage pulse. driver will automatically shut o if the xtures
are not properly wired. In this event, unplug and check the wiring and then plug it in again.

• For use with ELV dimmer.
INSTALLATION:

1. Loosen two cover screws and remove the cover. Inside there one sets of wiring terminals.

2. Push down one set of the wiring terminals and insert xture’s red wire into the “+” terminal and the black wire into
the “-” terminal.

3. After connecting all the LED xtures, secure the cover by tightening the two screws.

4. The product should be installed on the either internal or external surface of any indoor construction.

MOUNTING INSTRUCTIONS

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

LEDme® Class 2 Electronic Drivers

LD-700MA09-EDIM-IS

SAFETY INSTRUCTION

To reduce the risk of re, electric shock or injury to persons:

• Always turn o power at main switch prior to installation.

• System intended for installation by a qualied electrician, in accordance with NEC and local regulations.
Consult with local inspector to assure compliance.

• For use with LED loads.

Model LD-700MA09-EDIM-IS

Input Voltage 120Vac,60Hz

Input Current Max 0.1A

Output Current 700mA

Each Port Output Voltage 2-4V DC

Each Port Load 1-3PCS 1x3W LED Fixtures

Each Port Load Lead Wires 12-22AWG

Output Port 3 PCS

FEATURES:

• 700mA Constant Current for LED’s optimized and stable performance.

• Capable of supplying power to a single LED xture, or more LED xtures at once.

• Special circuit design to protect LED from high voltage pulse. Driver will automatically shut o if the xtures are
not properly wired. In this event, unplug and check the wiring and then plug it in again.

• For use with ELV dimmer.
INSTALLATION:

1. Loosen two cover screws and remove the cover. Inside there four separate sets of wiring terminals.

2. Push down one set of the wiring terminals and insert xture’s red wire into the “+” terminal and the black wire into
the “-” terminal.

3. After connecting all the LED xtures, secure the cover by tightening the two screws.

4. The product should be installed on the either internal or external surface of any indoor construction.

MOUNTING INSTRUCTIONS

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]