INSTALLATION INSTRUCTION
Endurance Wall Pack
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/cETL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/cETL esta lámpara.
A1 B1 B2
Wire connector
Qty: 3pcs
Junction box screw
Qty: 2pcs + 1 extra
Assembly screw with gasket
Qty: 2pcs + 1 extra
1
INSTALLATION INSTRUCTION
Endurance Wall Pack
FOR RECESSED JUNCTION BOX
STEP 1:
• Mount back plate and gasket to existing junction box with
junction box screws (B1) loosely, then tighten the screws.
STEP 2:
• Remove conduit and keyhole caps as needed.
• Wrap locking nut with tread seal tape to act as a sealant.
• Mount xture housing onto square canopy plate.
• Tighten locking nut to secure xture position.
Back Plate
B1
Locking
Nut
Fixture housing
Gasket Recessed Junction Box
(Existing)
Canopy
Hanging Cable
STEP 3:
• Hang xture housing canopy plate onto back using
hanging cable.
• Connect the electrical wires as shown in Fig. 1,
making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire,
connect the xture’s ground wire to it. After wires are
connected, tuck them carefully inside the junction box.
Fig.1 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
STEP 4:
• Mount xture housing and canopy onto back plate with
assembly screws with gasket (B2).
• Tighten all conduit caps with thread seal tape.
A1
Hanging Cable
B2
2
INSTALLATION INSTRUCTION
Endurance Wall Pack
FOR EXPOSED JUNCTION BOX
STEP 1:
• Remove conduit caps as needed.
• Wrap locking nut with thread seal tape to act as a sealant.
• Mount xture housing onto round canopy plate.
• Tighten locking nut to secure xture position.
STEP 2:
• Connect the electrical wires as shown in Fig. 1,
making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire,
connect the xture’s ground wire to it. After wires are
connected, tuck them carefully inside the junction box.
Fig.1 Wiring
Locking Nut
Fixture housing
Canopy
Gasket (Round)
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
STEP 3:
• Mount xture housing onto Junction Box with
junction box screws (B1).
• Tighten all conduit caps with thread seal tape.
B1
3
INSTALLATION INSTRUCTION
Endurance Wall Pack
ADJUSTING THE LUMINAIRE
• Vertical Adjustment: Loosen thumb screw, rotate
xture to desired angle (±90°), and tighten thumb screw.
• Rotation Adjustment: Loosen locking nut, rotate
xture to desired angle (360°), and tighten locking nut.
COMPLETING THE INSTALLATION:
To prevent moisture from entering the outlet box and causing a short, use caulking (i.e. silicone sealant) to outline the outside of Flood
junction box where it meets the wall while leaving the bottom side unsealed to allow moisture to escape.
Rotation Adjustment
Vertical Adjustment
Locking Nut
Thumb Screw
Note: Flood is suitable for wet location installations in all mounting orientations.
COMPATIBLE DIMMERS
BRAND MODEL NUMBER TYPE
ELV 120V
ELV 120V
ELV 120V
ELV 120V
4
Loading...