INSTALLATION INSTRUCTION
LED Step and Wall Lights - 12V
4031, 4041, 4051, 4061, 4071, 4091
WARNING
IMPORTANT: NEVER attempt to do any work without shutting off the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a quali ed electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien quali é en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/cETL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista cali cado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la cali cación ETL/cETL esta lámpara.
"
5
1 ¼"
OVERALL DIMENSIONS:
3"
3/8"
1 ¾"
4071
used as reference.
HARDWARE
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Junction Box Mounting Screw
Qty: 2 pcs
1/8”-40, * 3/4"
Stainless Steel
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Wire Nuts
Qty:
2 pcs
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FEBRUARY, 2017
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
LED Step and Wall Lights - 12V
4031, 4041, 4051, 4061, 4071, 4091
INSTALLATION AND WIRING
JUNCTION BOX: 2” x 4” boxes to have minimum inside dimensions of 3”H x 2”W x 2”D in order to accommodate fixtures.
Note:
Actual depth of box to be determined in accordance with the NEC and local ordinances. Indoor or outdoor frame mounted
junction box: Raco 2” x4”
weatherproof box Model S103E or equiv. recommended. Mortar or poured concrete installation: Use appropriate junction box
suitable for that particular application
Note: Determine junction box and step light orientation
(vertical/horizontal) prior to installation. Horizontal
installation shown below.
STEP 1:
• Install 2" x 4" junction box, and ensure it is water-tight
for outdoor use.
STEP 2:
Lead the wires from a low voltage magnetic transformer into
•
the junction box and waterproof the opening using a
conduit and thread seal tape or silicon sealant.
(16.5 cu. In) or equivalent recommended. Outdoor surface mounted junction box: Red Dot deep
Connect the fixture wires to the junction box wires using the
•
provided wire nuts
• Place all wiring and connectors back in the junction box.
STEP 3:
Use the provided junction box mounting screws to install
•
fixture onto the junction box.
STEP 5:
Hook the cover plate onto the LED light engine.
•
Push the cover plate towards the light engine until the
•
cover magnetically secures to the installation.
Junction Box
Mounting Screw
4071 used as reference.
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. FEBRUARY, 2017
Loading...