WAC Lighting W000233432 Installation & Assembly

INSTALLATION INSTRUCTION

Hawk - Endurance Wall Pack

WP-LED219, WP-LED227

WARNING

IMPORTANT: NEVER attempt to do any work without shutting o the electricity.

1. Read all instructions before installing.

2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

3. Place the wall switch in the “OFF” position.

4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out

or broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this xture.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez

pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/cETL du luminaire.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal

en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice

piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/cETL esta lámpara.

A1 B1 C1 C2 D1B2

Wire connector
Qty: 5pcs

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2014 1

Junction box screw
Qty: 2pcs + 1 extra

Bottom Cap screw
Qty: 2pcs + 1 extra

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Junction Box Cover screw
Qty: 2pcs + 1 extra

Housing Assembly screw
Qty: 2pcs + 1 extra

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

Housing Assembly
Rubber
Qty: 2pcs + 1 extra

INSTALLATION INSTRUCTION

Hawk - Endurance Wall Pack

WP-LED219, WP-LED227

FOR RECESSED JUNCTION BOX

STEP 1:

• Mount back plate and gasket to existing junction box with

junction box screws (B1) loosely, then level using built-in level
and tighten the screws.

STEP 2:

• Hang Fixture housing onto Back Plate using hanging cable.

• Connect the electrical wires as shown in Fig. 1, making sure

that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s
ground wire to it. After wires are connected, tuck them
carefully inside the junction box.

Fig.1 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

Back Plate

B1

Fixture housing

Gasket

Recessed Junction Box
(Existing)

Level

A1

Hanging Cable

Fixture Wires

Brown and Blue
(Use with 0 - 10V dimmers)

STEP 3:

• Mount xture housing onto back plate with housing

assembly screws (C2) and housing assembly rubber (D1).

STEP 4:

• Mount bottom cap onto xture housing with bottom cap

screws (B2).

• Tighten all conduit caps with thread seal tape.

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

C2

D1

Bottom Cap

B2

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. NOVEMBER, 2014 2