WAC Lighting SCOOP series, 6611, TOWER series, 6621, CHAMBER series Installation Instruction

...
INSTALLATION INSTRUCTION
Bollard Light 12V
6611/6621/6631/6641/6651
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
Read all instructions before installing.
System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
Place the wall switch in the “OFF” position.
Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the space that you are working on.
WARNING: Risk of electric shock. Install all luminaires 10 feet (3.05 m) or more from a pool, spa, or fountain.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION.
Lisez toutes les instructions avant d’installer.
Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
Placez l’interrupteur mural en position d’arrêt (« OFF »).
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
MISE EN GARDE
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire.
*Note: Transformer is required to power the xture. (sold separately)
THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:
*Note: Transformer is required to power the xture. (sold separately)
SCOOP
6611
MOUNTING ACCESSORIES (INCLUDED IN BOX)
TOWER
6621
CHAMBER
6631
PARK 6641
PARK 6651
Mounting Stake
Qty: 1pc
waclighting.com
Phone (800) 526.2588 Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 1
Headquarters/Eastern Distribution Center
44 Harbor Park Drive Port Washington, NY 11050
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key Qty: 1pc
Central Distribution Center
Western Distribution Center
1750 Archibald Avenue Ontario, CA 91760
INSTALLATION INSTRUCTION
Bollard Light 12V
6611/6621/6631/6641/6651
INSTALLATION
1. Make sure your main power is o.
2. Excavate a trench for the Mounting Stake.
The Mounting Stake requires approximately a one (1) square foot hole to facilitate installation. The excavated should be approximately 14” deep, depending on your local code. This will allow the hex-head set screw on the Mounting Stake to remain above ground when the installation is completed.
3. Secure Fixture Mounting Plate onto the Stake Metal Cap by
using the Stake Mounting Screws.
Bollard Fixture
4. Secure the Stake Metal Cap assembly onto the
Mounting Stake by tighten the Cap Mounting Screw (Note: Make sure the Fixture Mounting Plate is Oriented at desired position.)
5. Secure the Bollard Fixture on top of the Fixture
Mounting Plate using the Fixture Mounting Screws.
6. After proper wirings are done by using the outdoor rated wire
nuts, back ll the hole and make sure the xture is leveled and stable.
7. Turn the main power supply back on and make sure the
xtures light up.
Fixture Mounting Screw
Stake Mounting Screw
Cap Mounting Screw
Mounting Stake
Fixture Mounting Plate
Stake Metal Cap
waclighting.com
Phone (800) 526.2588 Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. 2
Headquarters/Eastern Distribution Center
44 Harbor Park Drive Port Washington, NY 11050
Central Distribution Center
Western Distribution Center
1750 Archibald Avenue Ontario, CA 91760
Loading...
+ 4 hidden pages