INSTALLATION INSTRUCTION
Mini Flood
5121
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
5. Risk of electric shock. Install all luminaires 10 feet (3.05m) or more from a pool, spa or fountain.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación UL esta lámpara.
This instruction apply to the model(s) below:
Installation Accessories
Wire Nut
Qty: 2pcs
7EAC352401
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY 7, 2017 11:45 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
5121-27/30BZ
5121-27/30BBR
Mounting Stake
Qty: 1pcs
7TVD207001BW
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
Mini Flood
5121
Step 1: Determining the location
1. Make sure your main power is o.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood.
Hammer till the bottom of the ring is ush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the ring is ush with the ground.
Fill the rest of the hole with the removed soil and pack it tight to
secure the stake.
4. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
Wood
Hammer
Mounting Stake
Soil
Lighting Fixture
Wire Slot
Fixture Wires
Mounting Stake
Step 2: Wiring the Fixture
*Note: Transformer is required to power the xture. (Sold Separately)
5. Cut the power supply wire from the transformer at the
location of the xture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
7. Strip o ½ inch of the insulating material from each wire and
connect one to each of the wires from the xture using the
outdoor rated direct burial wire nuts provided.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Note: To install multiple xtures, also connect the power
supply wire of each additional xture to the connection
described in 7 of the previous xture.
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Transformer
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY 7, 2017 11:45 AM
2
INSTALLATION INSTRUCTION
Mini Flood
5121
Step 3: Installing the Fixture
8. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench.
Close the trench by applying an inward force to both sides of
the trench.
10. Repeat steps for other xtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the xtures
light up
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the xture
to the desired direction before retightening the screw.
13. Loosen the mounting knob and rotate the xture to the desired
position before retightening the knob.
Note: To install multiple xtures, follow the diagram above
Tilting
Joint Screw
Mounting
Knob
Rotating
Transformer
Step 5: Dimming Adjustment:
14. Use a Philips head screwdriver to adjust the dimming dial and
the CCT dial
15. Rotate until the arrow on the dial is pointed at the desired
wattage and CCT.
NOTE:
a. The arrow on the CCT dial must be pointed at the 2700K
or the 3000K tabs.
b. The wattage may be adjusted to the pre-existing tabs
or any value in between.
16. The lower the wattage, the dimmer the xture will be.
17. There are two CCT settings available: 2700K or 3000K.
18. Please refer to the yellow tag to determine the size of the
required transformer.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY 7, 2017 11:45 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
2700 3000
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
2
6
1
8
3
INSTALLATION INSTRUCTION
Mini Flood
5121
ACCESSORIES
I. Color Lens:
Colored lens come in red, blue, green, amber, frosted, and beam spread to
lter the light coming out of the xture.
Installation: Put the lens onto the center of
the clip and push them onto the front of the xture.
II. Surface Mount Accessory
The surface mount accessory is used to mount the xture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10 Philips
head screws that are at least half an inch long. If mounting on concrete
or something similar, rst use a plastic anchor sized for No. 10 screws.
If mounting on a soft surface rst attach the included spikes.
Create a route underneath the accessory for your wire to travel through.
Lead your wire through the created route and screw your xture onto the
surface mount accessory.
III. Tree Mount Accessory:
The tree mount accessory is a way for xtures to be mounted on
the trunk or a branch of a tree while minimizing damage to the tree.
Installation: Mark the screw hole locations at the point of installation.
Thread one hex nut onto the screw until it is stopped by the wood screw
portion. Use a wrench to screw the bolt into the tree until the
unthreaded portion of the bolt meets the surface of the tree.
(Do this for all three bolts.) Place the tree mount bracket onto the bolts
and secure it using additional hex nuts. Attach light xture and lead wire
through the bracket. Place all wire nuts into the tree mount bracket.
LENS-2X3- LENS CLIP
No. 10 Tapping Screw
Surface Mount Canopy
Removable Spike
Wood Screw Bolt
Hex Nut
(included in LENS-2X3-)
Tree Mount
Junction Box
Hex Nut
IV. Extension Accessory
Using extension rods and rod joiners, xtures can be mounted
away from a surface in any desired direction.
Rods come in 5 sizes: 4 inches, 8 inches, 12 inches, 18 inches, and
24 inches. These rods can be connected via either straight or
90 degree rod joiners.
Installation: Screw in a rod joiner into your mounting accessory.
Screw an extension rod to the other side of the rod joiner.
Continue to use rod joiners and extension rods until the xture is
in the desired position.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JULY 7, 2017 11:45 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
90° Rod Joiner
Extension Rod
Rod Joiner
Mounting Accessory
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
Loading...