Wac lighting HR90 HR-LED90 User Manual

INSTALLATION INSTRUCTION

HR90 LED Undercabinet Button Lights

HR-LED90

WARNING

IMPORTANT: NEVER attempt to do any work without shutting o the electricity.

1. Read all instructions before installing.

2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

3. Place the wall switch in the “OFF” position.

4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power

to the space that you are working on.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or
broken. Failure to follow this instruction may invalidate the ETL/cETL listing of this xture.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/cETL du luminaire.

INSTALLATION
A) Recessed Mounting

NOTE: The back plate is not needed for recessed mounting
and may be discarded.

Back Plate

1. Cut a 3 1/4” diameter hole in the surface.

2. Feed the xture wires through the hole, and connect
the wires to a 24V transformer.

3. Compress the springs on either side of the cover piece
and insert it into the opening.

4. Fit the light xture into the cover piece. Light xture is held
in place by magnet.

Output
24V

Transformer

Input
120V

Cover Piece

Light Fixture

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2014 1

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

HR90 LED Undercabinet Button Lights

HR-LED90

B) Surface Mounting

NOTE: The cover piece is not needed for surface mounting and may be
discarded.

Cover Piece

1. Wires may be run behind the xture or along the mounting
surface. Determine the most convenient location for wire
passage.

2. Screw the back plate to the surface with screws provided.
Ensure that the screw’s heads level with back plate.

3. To wire behind the xture, drill a hole in the surface
sucient to allow the socket wires through.

4. Feed the xture wires through the hole, and connect
the wires to a 24V transformer.

5. Snap the light xture onto back plate. Light xture is held
in place by magnet.

WIRING

Installation within a cabinet require 24V Class 2 transformers.
Class 2 transformers are by denition “Power limited”
(5 amps maximum) and “Inherently Protected” (fused).
Primary wires to the transformer enclosure must follow normal NEC
Chapter 3 wiring techniques. Non-enclosed secondary wiring and
splices are not restricted in concealed spaces.

Leveling the screw

Wires behind the xture

Output
24V

Wires along the mounting surface

Light Fixture

Output 24V

Back Plate

Transformer

Transformer

Input
120V

Back Plate

Light Fixture

Input 120V

TRANSFORMERS:

Use to power the HR-90 button light. Below is a list of compatible transformer models and descriptions (sold separately)

Model Number Description

EN-2460-P-AR 60W plug-in transformer, 120V AC

EN-2460-RB2 60W remote transformer, 120V AC

EN-24100-RB2 96W remote transformer, 120V AC

WAC Lighting

www.waclighting.com
Phone [phone] • Fax [phone]

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. DECEMBER, 2014 2

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]