WAC Lighting dweLED 911 Series, dweLED WS-W14911F, dweLED WS-W14911 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

911-Outdoor Wall Sconce

WS-W14911/WS-W14911F

CAUTION:

TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER

BEFORE BEGINNING.

- Read all instructions before installing.

- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.

- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.

- Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by
dweLED could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.

MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.

MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.

- Lisez toutes les instructions avant l’installation.

- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.

- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou
accessoires non conçus pour ce produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également caus
l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

er

NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
rec

ommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes

les deux semaines avec un chiffon humide.

HARDWARE

A

Wire Connector
Qty: 3pcs+1 Extra

dweLED

www.dweLED.com
Phone [phone] • Fax [phone]

G0

dweLED retains the right to modify the design of our products at any time as part of the company's c

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

B

Mounting Screw

Qty:1 Extra

C

Silicon Gasket

Qty:1 Extra

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

ontinuous improvement program. Feb 2019

1

INSTALLATION INSTRUCTIONS

911-Outdoor Wall Sconce

WS-W14911

Fig.1

B

Mounting Screw

C

Silicon Gasket

A

Wire Connector

Junction Box

Back Plate Dimensions

Mounting Back Plate

Junction Box Screw

PREPARATION

1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.

CONNECTING THE WIRES (Fig. 2)

3. Remove the mounting screw (B) and silicone gas

4. Secure the mounting back plate to the junction box using the screws provided with the junction box.

NOTE: The s

5. Connect the fixture’s input wires to junction box wires as shown (Fig. 2). M
If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully
inside the junction box.

MOUNTING THE FIXTURE/ CONNECTING THE WIRE

6. Secure the canopy to the mounting plate using the mounting screw (B) and the silicone gasket (C).

7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to
outline the outside of fixture back plate where it meets the wall. Leave a space at a bottom to allow moisture to escape Fig.3.

ide of the mounting back plate marked “GND” must face out.

Fig.2Wiring

Fixture Wires House Wires

Black or Black
Smooth (Hot)

Fixture Wires House Wires

White or White
Ribbed (Neutral)

Fixture Wires House Wires

Bare wire Green or Bare Copper
(Ground) (Ground)

ket (C) from the fixture.

ake sure that all wire connectors (A) are secure.

Fig.3

Junction Box

Caulking

dweLED

www.dweLED.com
Phone [phone] • Fax [phone]

G0

dweLED retains the right to modify the design of our products at any time as part of the company's c

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

ontinuous improvement program. Feb 2019

2