WAC Lighting dweLED 649 Series, dweLED WS-W64905, dweLED WS-W64906, dweLED WS-W64908 Installation Instructions Manual
INSTALLATION INSTRUCTIONS
649 Outdoor Wall Sconce
178 – LED Wall Sconce
WS-W64905/ WS-W64906/ WS-W64908
WS-17825/WS-17837
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or acces-
sories designated for use by WAC Lighting/dweLED/Modern Forms. Substitution of parts or accessories not designated for use with this product
by WAC Lighting/dweLED/Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized
dealer or the manufacturer if any parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal areas MAINTENANCE NOTE:
clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements
locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting/dweLED/Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit WAC Lighting/dweLED/Modern Fo
également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
rms pourrait causer des dommages corporels ou matériels et pourrait
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux NOTE D’ENTRETIEN:
clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chion
humide.
HARDWARE
A
A
B
A
Wire Connector
Wire Connector
Qty: 3pcs+1 Extra
Qty: 3pcs+1 Extra
Wire Connector
7EAC112201 7MPF0415C2
Qty: 3pcs+1 Extra
Junction Box Screw
Qty: 2pcs+1 Extra
#8-32x5/8 SS
B
C
B
Junction Box Screw
Qty: 2pcs+1 Extra
7MPF0415C27EAC112201 7MPF0409S3(AL)
Mounting Screw
#8-32x5/8 SS
Mounting Screw
Qty: 1 Extra
7MPF0409S3(AL)
4MPF040902W5(WT)
Qty:1 Extra
5/32"-32X5/16
Rubber Gasket
4MPF040902W5(WT)
C
D
C
Mounting Screw
Wire Connector
Qty: 1 Extra
Qty: 1 Extra
7EAC140901
Qty:1 Extra
5/32"-32X5/16
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTIONS
649 Outdoor Wall Sconce
178 – LED Wall Sconce
WS-W64905/ WS-W64906/ WS-W64908
WS-17825/WS-17837
Fig. 1
A
Wire Connector
Backplate
C
C
Mounting Screw
D
Junction Box
Junction Box Wires
Junction Box Screw
C
Rubber Gasket
Mounting Screw
B
PREPARATION
PREPARATION
1.
2.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and the rubber gasket (C) from the mounting back plate.
CONNECTING THE WIRES (Fig. 2)
4. Secure the mounting plate to
3.
NOTE: The side of the mounting back plate marked “GND” must face out.
4. Connect the driver input wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
CONNECTING THE WIRES (Fig. 2)
the junction box using junction box screws.
Back Plate Dimensions
WS-W64905: 4 1/4"
F
A
A
Driver 2 3/4"L 1 1/4"W 1 3/16"H
WS-W64905: 3 7/8"
WS-W64906: 4 1/8"
Mounting Plate
B
WS-W64908: 5 7/8"
B
Junction Box Screw
Fixture
WS-W64908: 6 1/8"
Wire Connector
WS-W64906: 5 1/4"
n
e
e
l
a
/M
e
l
a
m
e
e
n
n
o
c
d
3
"
1
4
Junction Box
ssary for installation.
r
to
c
3
1
"
8
the mounting plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
5. Secure the mounting plate to the junction box using junction box screws (B). The side of the mounting back plate marked “GND” must face
COMPLETING THE INSTALLATION (Fig. 1)
out.
6.
7.
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
17837
S-
Fig. 2 Wiring
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
17825&W
S-
W
Fig. 3 Sealing
7MBC151106
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
D
pl
Back
Junction Box
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
ed. If your outlet box
wire directly to
.3.
e
at
Caulking
dweLED retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
2
Loading...