Page 1
INSTALLATION INSTRUCTION
Accent
5011
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación UL esta lámpara.
This instruction apply to the model(s) below:
*Note: Transformer is required to power the xture. (sold separately)
5011-27
5011-30
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 11, 2016 11:58 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
Page 2
INSTALLATION INSTRUCTION
Accent
5011
MOUNTING ACCESSORIES
Mounting Stake
Qty: 1pcs
Adjustable Shroud
Qty: 1pc
Step 1: Determining the location
1. Make sure your main power is o.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood.
Hammer till the bottom of the ring is ush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the ring is ush with the ground.
Fill the rest of the hole with the removed soil and pack it tight
to secure the stake.
4. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
Step 2: Wiring the Fixture
*Note: Transformer is required to power the xture. (sold separately)
Outdoor Rated Wire Nut
Qty: 2pcs
Wood
Hex Key
Qty: 1pcs
Hammer
Mounting Stake
Soil
Accent Lighting Fixture
Wire Slot
Fixture Wires
Mounting Stake
5. Cut the power supply wire from the transformer at the location
of the xture.
Transformer
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
To Next Fixture
7. Strip o ½ inch of the insulating material from each wire and
connect one to each of the wires from the xture using the
outdoor rated direct burial wire nuts provided.
Note: To install multiple xtures, also connect the power
supply wire of each additional xture to the connection
described in 7 of the previous xture.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 11, 2016 11:58 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
Page 3
INSTALLATION INSTRUCTION
Accent
5011
Step 3: Installing the Fixture
8. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. Close the
trench by applying an inward force to both sides of the trench.
10. Repeat steps for other xtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the xtures
light up.
Runs to
the next
xture
Transformer
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the xture
to the desired direction before retightening the screw.
13. Rotating: Loosen the mounting knob and rotate the xture to
the desired position before retightening the knob.
Step 5: Dimming Adjustment:
14. Use a Phillips head screwdriver to adjust the dimming dial.
15. Rotate until the arrow on the dial is pointed at the desired
wattage. The wattage may be adjusted to the pre-existing tabs
or any value in between.
16. The lower the wattage, the dimmer the xture will be.
17. Please refer to the yellow tag to determine the size of the
required transformer.
4W
2W
Tilting
8W
Mounting
Knob
Joint Screw
Rotating
13W
16W
Model: 5011
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 11, 2016 11:58 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
Page 4
INSTALLATION INSTRUCTION
Accent
5011
Step 6: Beam Angle Adjustment:
18. Note the four pre-determined beam angles on the beam angle
changing dial.
19. Use the provided Hex Key to sightly loosen the screw.
Do not remove screw from the xture.
CAUTION: the set screw should either be inset or ushed with
the surface of the xture. Do not extrude out and removed from
the xture at all times. It should only be taken out for xture
servicing. Consult factory for service instruction.
20. Rotate the dial until the arrow is aligned with the desired
beam angle. This beam angle may either be one of the
pre-determined ones or any number in between.
Hex Key
21. Tighten the set screw that is located on the beam angle dial to
lock the dial in place.
Step 7: Shroud Adjustment
22. Loosen the thumb screw on the shroud.
23. Rotate the shroud until it is in the desired position to properly
cut o glare.
24. Retighten the thumb screw to lock the shroud in place.
60
40
25
10
Beam Angle Dial
Shroud
Thumbscrew
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 11, 2016 11:58 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
Page 5
INSTALLATION INSTRUCTION
Accent
5011
ACCESSORIES
I. Lens Accessory:
Frosted, red, blue, green and amber lens accessories are used to alter the
spectrum and distribution of the light coming out of the xture.
Installation: Place the lens in between the xture and the shroud.
Tighten the thumb screw on the shroud to secure the lens in place.
II. Surface Mount Accessory
The surface mount accessory is used to mount the xture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10 Philips
head screws that are at least half an inch long. If mounting on concrete
or something similar, rst use a plastic anchor sized for No. 10 screws.
If mounting on a soft surface rst attach the included spikes.
Create a route underneath the accessory for your wire to travel through.
Lead your wire through the created route and screw your xture onto
the surface mount accessory.
Shroud
Lens Accessory
No. 10 Tapping Screw
Surface Mount
Accessory
Removable Spike
III. Tree Mount Accessory:
The tree mount accessory is a way for xtures to be mounted on
the trunk or a branch of a tree while minimizing damage to the tree.
Installation: Mark the screw hole locations at the point of installation.
Thread one hex nut onto the screw until it is stopped by the wood screw
portion. Use a wrench to screw the bolt into the tree until the
unthreaded portion of the bolt meets the surface of the tree.
(Do this for all three bolts.) Place the tree mount bracket onto the bolts
and secure it using additional hex nuts. Attach light xture and lead wire
through the bracket. Place all wire nuts into the tree mount bracket.
IV. Extension Accessory
Using extension rods and rod joiners, xtures can be mounted
away from a surface in any desired direction.
Rods come in 5 sizes: 4 inches, 8 inches, 12 inches, 18 inches, and
24 inches. These rods can be connected via either straight or
90 degree rod joiners.
Installation: Screw in a rod joiner into your mounting accessory.
Screw an extension rod to the other side of the rod joiner.
Continue to use rod joiners and extension rods until the xture is
in the desired position.
Tree Mount BracketHexnutWood Screw Bolt
90° Rod Joiner Extension Rod
Rod Joiner
Mounting Accessory
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY 11, 2016 11:58 AM
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
5
Loading...