Würth Elektronik WA-SBRRO Datasheet

Dimensions: [mm]

A

A

sectional drawing A-A

O

6,0

L

u

0,1

3,2

O

Properties:

Properties Value Unit

Inner Diameter Ø ID 3.2 mm

Outer Diameter Ø OD 6 mm

Material Brass

Surface Nickel

Certification:

RoHS Approval Compliant [2011/65/EU&2015/863]

REACh Approval Conform or declared [(EC)1907/2006]

Halogen Free Conform [IEC 61249-2-21]

Halogen Free Conform [JEDEC JS709B]

General Information:

Operating Temperature -55 up to +150 °C

Storage Conditions (in original
packaging)

Moisture Sensitivity Level (MSL) 1

< 40 °C ; < 75 % RH

Article Properties:

Properties Value Unit

Length L 9 mm

Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

74638 Waldenburg
Germany
Tel. [phone] - 0
www.we-online.com
[e-mail]

CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PROJECTION

JuSa 001.002 2020-10-14 DIN ISO 2768-1m

DESCRIPTION

METHOD

WA-SBRRO Round Brass Spacers

ORDER CODE

963090042

BUSINESS UNIT STATUS PAGE

eiCan Valid 1/3

Cautions and Warnings:

The following conditions apply to all goods within the product series of WA-SBRRO of
Würth Elektronik eiSos GmbH & Co. KG:

General:

• This mechanical component is designed and manufactured for use in general electronic equipment.

• Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any
equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control,
ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are
especially required and/or if there is the possibility of direct damage or human injury.

• Mechanical components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer.

• The component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions
specified in the datasheet are not met, the component may be damaged or dissolved.

• Do not drop or impact the components, the component may be damaged.

• Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth
Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and
sustainability over time.

• The responsibility for the function of the application of the customer specific products and use in a particular customer design is always
the full and autonomous responsibility of the customer. All technical specification for standard products also apply to customer specific
products.

Product Specific:

Cleaning and Washing:

• Washing agents used during the production to clean the customer application might damage or change the characteristics of the
components. Washing agents may have a negative effect on the long-term functionality of the product.

• Using a brush during the cleaning process may damage the component. Therefore, we do not recommend using a brush during the PCB
cleaning process.

Storage Conditions:

• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer
degradation, resulting in bad processability. Therefore, all products shall be used within the period of 12 months based on the day of
shipment.

• Do not expose the components to direct sunlight.

• The storage conditions in the original packaging are defined according to DIN EN 61760-2.

• The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components.

Handling:

• The maximum permissible torques must be complied with to prevent mechanical destruction of the component and PCB.

• If a component is pre-assembled with an adhesive tape, the adhesive duration cannot be guaranteed. This depends on the surface
where the component will be mounted on. It also depends on the environmental conditions the component is exposed to. The customer
has to evaluate this for his specific application.

• Violation of the technical product specifications will void the warranty.

• Coated metal parts may have spots and/or deposits because of the rinsing and drying process during plating. The storage and
processability are not affected.

• The temperature rise of the component must be taken into consideration. The operating temperature is comprised of ambient
temperature and temperature rise of the component.The operating temperature of the component shall not exceed the maximum
temperature specified.

These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.
However, no responsibility is assumed for inaccuracies or incompleteness.

Potting and Coating:

• If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking
could lead to an incomplete seal, allowing contaminants into the components. Expansion could damage the components. We
recommend a manual inspection after potting or coating to avoid these effects.

CHECKED REVISION DATE (YYYY-MM-DD) GENERAL TOLERANCE PROJECTION

JuSa 001.002 2020-10-14 DIN ISO 2768-1m

DESCRIPTION

Würth Elektronik eiSos GmbH & Co. KG
EMC & Inductive Solutions
Max-Eyth-Str. 1
74638 Waldenburg
Germany
Tel. [phone] - 0
www.we-online.com
[e-mail]

This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH
& Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety
must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.

WA-SBRRO Round Brass Spacers

BUSINESS UNIT STATUS PAGE

eiCan Valid 2/3

METHOD

ORDER CODE

963090042