1011458-R03
Installation instructions
25/06/2018
Range hood
Mode: Extraction / Recirculation
1011458-R03
DSTS9
The appliance should be installed by qualified personnel only.
Each step must be carried out and checked in full in the order specified.
Validity
64004 (DSTS9, construction width 90 cm)
General notes
Identification plate
Remove the grease filters. The identification plate is located on the inside of the appliance.
Installation accessories supplied
All fixing elements are contained in the scope of delivery.
Mains cable |
12 self-tapping screws 3.5 × 9.5 mm |
Lower angle bracket |
6 screws M4 × 8 mm |
Upper angle bracket |
6 screws 4 × 15 mm |
Angle brackets |
Accessories: Recirculation box |
(are not used) |
|
Extraction mode
The extracted air must not be fed into a chimney which is used for exhausting fumes from appliances burning gas or other fuels.
Observe the local fire regulations.
Recirculation mode
The air outlet grille must not be covered during operation.
1
1011458-R03
Installation instructions
25/06/2018
Range hood
Mode: Extraction / Recirculation
1011458-R03
DSTS9
Dimensions
Cannot be installed in conjunction with a gas hob.
Recessed installation variant
120 
|
|
|
|
|
8 |
|
|
|
|
|
|
|
|
|
|
|
8 |
|
|
|
|
|
|
|
|
|
|
|
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
|
|
7 |
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
65 |
|
|
250 |
8 |
|
|
|
|
|
|
|
116 |
400 |
|
2 |
|
|
|
|
|
|
|
|||
|
|
0 |
|
|
|
|
|
|
|
|
|
332 |
|
|
|
|
|
|
|
|
|
102 |
|
|
98 |
|
|
|
|
|
|
2.4 |
|
||
|
|
332 |
|
|
|
2 |
|
|
|
646 |
|
|
|
|
|
|
|
|
|
|
|||
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
166 |
|
|
|
|
|
|
|
|
|
|
|
17 |
|
|
(ø150) |
|
|
||||
|
|
|
|
|
|
|
|
|
|
10–200 |
|
|
|
- |
|
|
|
|
|
8 |
|
|
|
|
|
1 |
|
|
|
|
|
1 |
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
|
|
108 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
30 |
|
|
|
|
|
≥30 |
|
|
|
|||
≥660 |
|
|
|
|
|
|
|
5 |
3 |
|
|
|
|
|
|
R |
|
|
|
|
|||
|
|
|
|
|
|
0 |
|
|
|
|
|
|
|
|
|
|
|
|
– |
|
|
|
|
Flush installation variant |
|
|
7 |
|
|
108 |
R0–5 |
R5 |
4 |
|
|
812 |
|
|
884 |
|
124 |
4 |
|
884 |
|
|
|
R0–5 |
124 |
812 |
|
||
|
|
7 |
|
108 |
|
|
|
R5 |
124 |
|
|
108 |
7 |
|
1The fan can be rotated for mounting. The exhaust air can thus be extracted upwards, left, right or downwards. The fan can also be mounted in the same position at the back of the appliance. If the fan is mounted at the back of the appliance, the back panel of the cabinet has to be cut out in the mounting area and sufficient installation space must be provided behind the cabinet.
2The electrics can, if required, be positioned to the left of the fan, on the hood body or in the cabinet.
3Ensure that the material is sufficiently stable.
4Stepped milling required if installed flush in a work surface made of natural stone (granite, marble). Exhaust air connection ø150 mm.
2
1011458-R03
Installation instructions
25/06/2018
Range hood
Mode: Extraction / Recirculation
1011458-R03
DSTS9
Installation
Carefully insert the hood body 1 in the prepared cut-out 2 (see
Dimensions).
1
For flush installation, level the hood body at the right height (using spacer set H6.0330).
2
Fasten the lower brackets 3 to the housing 5 of hood body 1 us-
ing two screws 4 for each bracket so that the feet 6 rest on the
base of the cabinet.
1
The brackets can also be rotated for mounting.
5
3
4
6
4×
3.5×9.5 mm
3
Loading...