VVG VNG 612 Instruction Manual

V
NG
6
1
2
V
NG
6
1
2
VNG 612
VVG Befestigungstechnik
Ein Unternehmen der HONSEL-Gruppe Ein Unternehmen der HONSEL-Gruppe
BLINDNIETMUTTERN
BLIND RIVET NUTS
BLINDNIETGEWINDEBOLZEN
M5 - M6 - M8
BLIND RIVET BOLTS
310.612.000.000
BEDIENUNGSANLEITUNG
INSTRUCTION MANUAL
7
11
22
11
22
1x
8
Nach dem Setzvorgang stellen Sie den Klinkenhebel nach unten/hinten (1) und bewegen den hinteren Zangenhebel einmal zur Entlastung in die entgegengesetzte Richtung (2).
Bring the small trigger into the rear position after setting (1) and move the back­ward bracket into the opposite direction for release one-time (2).
Abschließend kann der Gewindedorn mit der Rändelschraube aus der gesetz­ten Blindnietmutter herausgeschraubt werden.
Finally unscrew and remove the mandrel from the blind rivet nut with the help of the knurled nut.
A B C
11
33
44
22
Wechsel Gewindedorn (Gewindehülse) | Change of the mandrel (threaded sleeve)
Lösen Sie das montierte Mundstück (1) und entfernen Sie den Gewindedorn (Gewindehülse) (2). Wählen Sie den Gewindedorn (Gewindehülse) für die neue Abmessung aus und positionieren Sie Ihn analog zur Entnahme wieder im Werkzeug (3). Nehmen Sie dann das zur ausgewählten Gewindedorngröße passende Mundstück und befestigen hiermit den Gewindedorn (4).
Release the assembled nosepiece (1) and remove the mandrel (2). Choose the mandrel (threaded sleeve) for the new size and insert it to the tool again (3). Finally take the fitting nosepiece and fix to the chosen mandrel.
kg
VNG612
GEWICHT AUSSTATTUNG
VERPACKUNG
WEIGHT ACCESSORY
PACKAGE
: :
:
1,1 kg 6 Umrüstsätze Blindnietmuttern, 3 Umrüstsätze Blindnietgewindebolzen Koffer in Aluminium-Optik
M4 M5 M6 M8 M10 M12
Aluminium | Aluminium
Stahl | Steel
Stahl | Steel
Edelstahl | Stainless Steel
M4 M5 M6 M8 M10 M12
1
Die Zangenschenkel soweit herausdrehen, dass ein kleiner Spalt entsteht und die Skala sichtbar ist.
Twist the levers until the scale is visible in a small gap.
Twist the levers until the scale is visible in a small gap.
2
A
B
Blindnietmutter -A- (Blindnietgewindebolzen -B-) auf Gewindedorn (Gewindehülse) aufschrauben.
Screw the blind rivet nut -A- (bolt -B-) onto the mandrel (threaded sleeve).
3
A
B
Die Blindnietmutter (-A-) soweit auf den Gewindedorn aufschrauben und justieren, dass alle Gewindegänge erfasst werden und der Gewindedorn leicht übersteht. Dabei liegt der Setzkopf der Mutter am Mundstück der Zange an. Das Vorgehen bei der Verwendung von Blindnietgewindebolzen -B- erfolgt analog.
All turns of the blind rivet nuts thread must be captured by the mandrel. The mandrel has to overlap a little. The setting head of the nut suits directly to the nosepiece. The treatment of blind rivelt bolts occurs in the same way.
4 5 6
11
22
11
22
TEST
Beim Setzen der Blindnietmutter (Blindnietgewin­debolzen) ist die Skala (>>Bild 1) zu beachten, die zurückgelegten Weg des Klemmbereiches anzeigt.
Observe that the screwed blind rivet nut (blind rivet bolt) and the mandrel (threaded sleeve) are brought into pretension to each other to activate the ratched function!
Nach dem Aufschrauben der Blindnietmutter (Blindnietgewindebolzen) ist unbedingt darauf zu achten, dass diese mit dem Gewindedorn (Gewindehülse) gegeneinander auf Vorspannung gebracht werden, damit die Ratschenfunktion aktiviert wird.
Check the scale (>>Picture 1) that shows the distance of the grip range.
Stellen Sie den kleinen Hebel am vorderen Schenkel vor dem Setzvorgang nach oben /vorn (1). Halten Sie diesen Schenkel fest und beginnen dann den hinteren Schenkel in vor und zurück zu bewegen (2) bis die Blindnietmutter (Blindnietgewindebolzen) korrekt und vollständig gesetzt ist (3).
33
Put the small trigger on the front bracket into the upper position (1). Hold this bracket tight and start to move the backward bracket back and forth (2) until the blind rivet nut (blind rivet bolt) is set in a correct and complete way (3).
Bei der Bestimmung der richtigen Blindnietmutter (Blindnietgewindebolzen) ist darauf zu achten, dass der angegebene Klemmbereich nicht überschritten wird! Die fehlerfreie Funktion des verarbeiteten Verbinders kann sonst nicht gewährleistet werden! Beachten Sie beim Gewindedornwechsel (Gewindehülse), dass jeweils das passende Mundstück verwendet wird!
Verwenden Sie nur Original -Ersatzteile!
Ensure that the grip range of the chosen blind rivet nut (blind rivet bolt ) will not exceeded. Otherwise the correct function of the fastener can not be guaranteed. Please consider that the used mandrel (threaded sleeve) always matches to the nosepiece.
Use original spare parts only!
: :
:
1,1 kg
6 Conversation kits for blind rivet nuts 3 Conversation kits for blind rivet bolts Case in aluminium optics
Loading...