Vulcan Materials VC4GC, VC6GC, VC44GC, VC66GD User Manual

OPERATION MANUAL

VC SERIES GAS CONVECTION OVENS

MODELS

VC4GD ML-126611 VC4GC ML-136494 VC6GD ML-126613 VC6GC ML-136495

INSTALLATION &

STACKED MODELS

VC44GD ML-126611 VC44GC ML-136494 VC66GD ML-126613 VC66GC ML-136495

For additional information on Vulcan-Hart or to locate an authorized parts

and service provider in your area, visit our website at www.vulcanhart.com

VULCAN-HART DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC

MODEL VC4GD

P.O. BOX 696

LOUISVILLE, KY 40201-0696

WWW.VULCANHART.COM

FORM 31123 Rev. K (Mar. 2009)

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

Improper installation, adjustment,

alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

IN THE EVENT OF A POWER FAILURE, DO NOT ATTEMPT TO OPERATE THIS DEVICE.

– 2 –

Installation, Operation and Care of

VC SERIES

GAS CONVECTION OVENS

KEEP THIS MANUAL FOR FUTURE REFERENCE

GENERAL

Models VC4GD and VC6GD feature a solid state temperature control. Models VC4GC and VC6GC feature a programmable oven controller. One hour dial timer is standard; five hour timer is optional. Two-speed additional oven racks are available. The burner input rating for each oven is 44,000 BTU/hr.

Porcelain interior is standard on all models. Model VC6GD and VC6GC has a 4 inches (102 mm) deeper oven cavity. Standard ovens are 120 V, 60 Hz, 1 PH and include cord and plug. Optional electrical specifications

of 208/240 V are available and require hard wire connection.

/2 HP (0.37 kw) electric motor is standard equipment. Each oven is furnished with 5 racks;

Independently opening doors are standard; simultaneous door opening is optional. Other options include: an open stand with lower storage rack, roast and hold, and a stacking kit for

mounting one oven on top of another. Vulcan VC Series Gas Convection Ovens are produced with quality workmanship and material. Proper

installation, usage and maintenance of your oven will result in many years of satisfactory performance. It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions

provided.

FEATURES AND OPTIONS

Model Thermostat Timer

VC4GD VC6GD Std. Opt. (654 mm)

VC4GC VC6GC (654 mm)

Stacked 8"

Ovens (203 mm)

Solid State

Programmable N/A N/A Std. Std.

1 Hr. 5 Hr.

Oven Roast &

Lights Hold Storage Rack

Std. Opt.

Legs

253/4

Stand with

Opt.

Voltage

120/60/1 Std. 208/60/1 Opt. 240/60/1 Opt.

240/50/1 Opt. 220/380 (3W)/50/3 Opt. 220/380 (4W)/50/3 Opt. 240/415 (4W)/50/3 Opt.

– 3 –

INSTALLATION

Before installing, verify that the electrical service and type of gas supply (natural or L.P.) agree with the specifications on the rating plate, located behind the top trim panel on the front of the oven. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact your dealer or Vulcan-Hart Company immediately.

UNPACKING

This oven was inspected before leaving the factory. The transportation company assumes full responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for possible shipping damage. If the oven is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.

Carefully unpack the oven and place it in a work-accessible area near to its final installed position. Do not use the doors or their handles to lift the oven.

LOCATION

The equipment area must be kept free and clear of combustible substances. When installed, minimum clearance from combustible construction must be 1 inch (25 mm) at the left

side, 4 inches (102 mm) at the right side and 2 inches (51 mm) at the rear. Minimum clearance from noncombustible construction must be 0 inch (0 mm) at the left side, 4 inches (102 mm) at the right side and 2 inches (51 mm) at the rear. The oven may be installed on combustible floors.

The installation location must allow adequate clearances for servicing and proper operation. For solid state and digital control models, there must be 18 inches (457 mm) of clearance on the right side of the oven from any open flame.

The oven must be installed so that the flow of combustion and ventilation air will not be obstructed. Adequate clearance for air openings into the combustion chamber must be provided. Make sure there is an adequate supply of air in the room to allow for combustion of gas at the oven burners.

Do not permit fans to blow directly at the oven. Wherever possible, avoid open windows next to the oven. Avoid wall-type fans which create air cross currents within the room.

INSTALLATION CODES AND STANDARDS In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI/Z223.1/NFPA #54 (latest edition). Copies may be obtained from The American Gas Association, Inc., Accredited Standards Committee Z223 @ 400 N. Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA, 1 Batterymarch Park, Quincy, MA 02169-7471.

NOTE: In the Commonwealth of Massachusetts,

All gas appliances vented through a ventilation hood or exhaust system equipped with a damper or with a power means of exhaust shall comply with 248 CMR.

– 4 –

3. Vapor Removal From Cooking Equipment

CONNECT

GAS LINE

STRAIN RELIEF

HERE

PL-53563

, NFPA-96 (latest edition). Copies may be obtained from

The National Fire Protection Association, Batterymarch Park, Quincy, MA 02169-7471.

National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The National Fire Protection Association, Batterymarch Park, Quincy, MA 02169-7471.

In Canada:

1. Local codes.

2. CSA B149.1 Natural Gas and Propane Installation Code.

3. CSA C22.1 Canadian Electric Code (latest edition).

The above are available from the Canadian Standard Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6.

INSTALLING BASIC OVEN

The basic oven must be installed on legs or be mounted on a modular stand. Installations on concrete bases or other supports restricting air circulation underneath the oven is not advisable and may void the warranty.

Ovens Mounted on Casters

Ovens mounted on casters must use a flexible connector (not supplied by Vulcan) that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 • CSA

6.16 and a quick-disconnect device that complies with the

Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI-Z21.41 • CSA 6.9. In addition, adequate means must be provided to limit movement of the appliance without depending on the connector and the quick-disconnect device

Fig. 1

or its associated piping to limit appliance movement. Attach the restraining device at the rear of the oven as shown in Fig. 1.

Remove two screws from the rear of the oven and install the tie-down strap shipped with the casters using these screws (Fig. 1). Attach the gas line strain relief to the tie-down strap at the rear of the oven (Fig. 1).

If disconnection of the restraint is necessary, turn off the gas supply before disconnection. Reconnect this restraint prior to turning the gas supply on and returning the oven to its installation position.

Separate instructions for installing casters to the oven are included with the casters. Note: If the oven is installed on casters and is moved for any reason, it is recommended that the oven

be releveled front to back and side to side.

– 5 –

Assembling the Legs to the Oven

STACKING FLUE

PL-53564

BACK

FRONT

RACK SUPPORT

RACK GUIDE

PL-56178

The legs must be installed on the bottom of the oven. Gently position the oven on its side, taking care not to scratch or damage it.

Attach each of the four leg assemblies to the bottom of the oven with the 24 bolts and lockwashers (six per leg). Carefully raise the oven to its normal position.

ASSEMBLING THE STAND TO THE OVEN

Attach each of the four leg assemblies to the bottom of the oven with the 24 bolts and lockwashers (six per leg). Carefully raise the oven to its normal position.

Attach the undershelf to the legs with eight bolts and lockwashers (two per leg).

Install the rack guides into the undershelf at desired locations (for pan or flat rack), then attach the rack supports to the top end of the rack guides. Attach rack supports to the leg assembly by removing one middle bolt and reattaching back through the end holes in the rack support (Fig. 2).

Fig. 2

ASSEMBLING STACKED OVENS

Unpack the ovens and stack kit. Position the oven to be used as the bottom oven on its back for access to the oven bottom, taking care not to scratch or damage it. The gas pipe protrudes beyond the back; provide for this when the oven is tipped back by resting it on suitable spacers (2 x 4" [51 x 102 mm], etc.). Attach the four leg assemblies with the 24 bolts and lockwashers (six per leg).

Place the lower oven (with legs) on the floor and remove two

/16 inch (11 mm) diameter knockouts on each side of the top cover. Remove vent guard and discard it.

Move the oven with legs to the installed position and place upper oven on top of lower oven using the locating studs.

Install the stacking flue (Fig. 3) with the four screws provided. Connect the piping between the top oven and bottom oven. For all

gas supply connections, pipe joint compound must be resistant to the action of propane gases.

LEVELING

Fig. 3

Make sure that the oven racks are level in the final installed position. If the oven is installed on legs, turn the adjustable feet in or out to level the oven front-to-back and side-to-side. If the oven is installed on casters, loosen set screws and turn casters in or out to level the oven front-to-back and side-to-side. Retighten set screws after leveling.

– 6 –

GAS CONNECTION

GAS DATA

INPUT RATING MANIFOLD PRESSURE

MODEL

VC4GD VC6GD VC4GC VC6GC

VC4GD-SEF

(With Standing Pilot)

Natural

44,000 BTU/hr 44,000 BTU/hr 3.5" W.C. (0.9 kPa) 10" W.C. (2.5 kPa)

44,000 BTU/hr 44,000 BTU/hr 3.7" W.C. (0.93 kPa) 10" W.C. (2.5 kPa)

L.P. GASES L.P. GASES

(Propane)

Natural

(Propane)

Gas supply connections and any pipe joint compound must be resistant to the action of propane gases. Location of the gas inlet is at the rear of the oven. Codes require that a gas shutoff valve must be

installed in the gas line ahead of the oven. Connect gas supply after leveling the oven. The gas supply line must be at least the equivalent of

/4 inch (19 mm) iron pipe. Make sure the pipes are clean and free of obstructions, dirt or pipe joint

compound. The ovens are equipped with fixed burner orifices which coincide with installation elevation. Standard oven with electronic ignition is provided with a regulator integral to the gas solenoid valve and

requires no external regulator. Ovens with standing pilot must use external regulator provided with unit, set to pressures as indicated

in above gas data chart.

The gas pressure regulator provided with this appliance must be used. This regulator is set

for an outlet pressure of 3.5” W.C. (0.9 kPa) natural gas and 10” W.C. (2.5 kPa) propane gas.

Prior to lighting, check all joints in the gas supply for leaks. Use soap and

water solution. Do not use an open flame.

A. Check all joints prior to the gas valve (solenoid) before lighting unit. B. Check all joints beyond gas valve (solenoid) after unit is lit.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When gas supply pressure exceeds

/2 psig (3.45 kPa), the oven and its individual shutoff valve must

be disconnected from the gas supply piping system.

When gas supply pressure is

/2 psig (3.45 kPa) or less, the oven should be isolated from the gas supply

system by closing its individual manual shutoff valve.

BURNER AIR ADJUSTMENT

Although main burner air is adjusted before shipment, it should be checked at the time of installation. Excessive air will cause flames to lift off a burner when cold or may cause flash-back during normal cycling of oven, particularly when propane gas is used.

– 7 –

ATADLACIRTCELE

sledoMHP/zH/V

yticapmAtiucriCmuminiM

eciveDevitcetorPmumixaM

SPMA

DG4CV DG6CV

1/06/021 1/06/802 1/06/042 1/05/042

3/05/)W3(083/022 3/05/)W4(083/022 3/05/)W4(514/042

51 51 51 51 51 5

.)noitidetsetal(07-APFN,edoClacirtcelElanoitaNehthtiwecnadroccanidelipmoC

Insufficient air will cause flames to burn with a yellow tip and result in carbon accumulation in the flame chamber and heat exchanger tubes.

Contact your local Vulcan-Hart servicer if required.

VENT SYSTEM DO NOT obstruct the flow of flue gases from the flue located on the rear of the oven. It is recommended

that the flue gases be ventilated to the outside of the building through a ventilation system installed by qualified personnel.

Ovens may use an optional down-draft diverter flue method. This optional down-draft diverter must be purchased from the oven manufacturer and vented to the outside; otherwise, the installation of any such device will void all oven certifications and warranties. This oven is suitable for connection to Type B Gas Vent when used with the draft hood provided.

From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18 inches (457 mm) must be maintained.

Information on the construction and installation of ventilating hoods may be obtained from

Removal from Cooking Equipment

, NFPA Standard No. 96 (latest edition), available from the National

Vapor

Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

ELECTRICAL CONNECTIONS

Electrical and grounding connections must comply with the applicable

portions of the National Electrical Code and/or other local electrical codes.

Appliances equipped with a flexible electric supply cord are provided with

a three-prong grounding plug. It is imperative that this plug be connected into a properly grounded three-prong receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do not remove the grounding prong from this plug.

VC series ovens with 120 V/60 Hz/1 PH electrical specification are equipped with a cord and plug as standard equipment.

A wiring diagram is located on the inside of the control housing.

VC4GD VC6GD VC4GC VC6GC

– 8 –

OPERATION

THERMOSTAT

MASTER SWITCH

OFF

HEAT

IGNITION

OVEN COOL

TIMER

OFF

LIGHTS

FAN SPEED

150

225

250

275

300

325

350

375

200

400

425 450

250

475

500

100

PL-53547

LIGHTING INSTRUCTIONS

SHUTDOWN INSTRUCTIONS

TURN GAS AND MASTER SWITCH "OFF"

TURN GAS "ON" PUSH MASTER SWITCH "ON" IF BURNER FAILS TO LIGHT

TURN GAS "OFF"

WAIT 5 MINUTES FOR RETRIAL

OFF

PL-53562

TIMER

OFF

LIGHTS

FAN SPEED

THERMOSTAT

MASTER SWITCH

OFF

HEAT

IGNITION

OVEN COOL

150

225

250

275

300

325

350

375

200

400

425 450

250

475

500

100

LIGHTING INSTRUCTIONS

SHUTDOWN INSTRUCTIONS

TURN GAS AND MASTER SWITCH "OFF"

TURN GAS "ON"

PUSH MASTER SWITCH "ON"

IF BURNER FAILS TO LIGHT

TURN GAS "OFF"

WAIT 5 MINUTES FOR RETRIAL

The oven and its parts are hot. Use care when operating, cleaning or

servicing the oven. CONTROLS (Models VC4GD and VC6GD Without Roast & Hold)

Master Switch ON — Turns oven control circuits on.

On Light (Amber) — Lit when Master Switch is ON. Heat Light (White) — Comes on and goes off when the burner cycles on and off.

Ignition Light (Red) — Comes on if burner fails to ignite. When lighting the oven, the IGNITION

Thermostat — Controls oven temperature during cooking operation. Timer (1 Hr. or 5 Hr.) — Sets the bake time. Buzzer sounds continuously after timer counts down

Fan Speed Switch — Allows you to select HI or LO Fan Speed. Lights Switch — Turns the lights in the oven ON or OFF.

OFF — Turns oven control circuits off.

OVEN COOL — Allows the fan motor to run with the doors ajar to speed ovencooling.

light flashes.

to 0. Oven does not turn off. Turn Timer to OFF to stop buzzer. When oven is not in use, keep Timer at OFF position.

– 9 –

CONTROLS (Models VC4GD and VC6GD With Roast & Hold)

OFF

150

225

250

275

300

325

350

375

200

400

425 450

250

475

500

100

THERMOSTAT

PL-53551

OFF

LIGHTS

NORMAL

R & H

FUNCTION

MASTER SWITCH

OFF

HEAT

IGNITION

OVEN COOL

TIMER

OFF

R & H TIMER

OFF

PL-53550

OFF

LIGHTS

R & H

FUNCTION

NORMAL

OFF

TIMER

150

225

250

275

300

325

350

375

200

400

425 450

250

475

500

100

THERMOSTAT

MASTER SWITCH

OFF

HEAT

IGNITION

OVEN COOL

R & H TIMER

Master Switch ON — Turns oven control circuits on.

OFF — Turns oven control circuits off.

OVEN COOL — Allows the fan motor to run with the doors ajar to speed ovencooling.

On Light (Amber) — Lit when Master Switch is ON. Heat Light (White) — Comes on and goes off when the burner cycles on and off.

Ignition Light (Red) — Comes on if burner fails to ignite. When lighting the oven, the IGNITION

light flashes.

Thermostat — Controls oven temperature when Function switch is on NORMAL or during

the first stage of Roast & Hold.

R & H Timer — Sets the first stage cooking time in Roast & Hold. Timer (1 Hr. or 5 Hr.) — Sets the bake time when Function switch is on NORMAL. Buzzer sounds

continuously after timer counts down to 0. Oven does not turn off at end of cycle. Turn Timer to OFF to stop buzzer. When oven is not in use, keep timer at OFF position.

Function Switch — Allows you to select Normal or Roast & Hold (R & H).

Normal: Uses the regular timer and high fan speed. R & H: Uses the R & H Timer for the first stage of roasting at the

thermostat setting, selects a hold temperature of 160°F (71°C) during

Lights Switch — Turns the lights in the oven ON or OFF.

second stage roasting. Uses low fan speed when burners are on.

– 10 –

CONTROLS (Model VC4GD-SEF)

(With Standing Pilot)

Master Switch

ON — Turns oven control circuits on.

OFF — Turns oven control circuits off.

SHABBOS — Puts oven in Sabbath mode allowing oven to operate when doors are open.

On Light (Amber) — Lit when Master Switch is ON or in Shabbos mode. Heat Light (White) — Lit when thermostat calls for more heat. Thermostat — Controls oven temperature during cooking operation. Timer (1 Hour) — Sets the bake time. Buzzer sounds continuously after timer counts down

to 0. Oven does not turn off. Turn Timer to OFF to stop buzzer. When oven is not in use, keep timer in OFF position.

Fan Speed — Allows you to select HI or LOW Fan Speed. Lights Switch — Turns the oven lights ON or OFF.

– 11 –

BEFORE FIRST USE

Before using the oven for the first time, it must be "burned in" to release any odors that might result from heating the new surfaces in the chamber.

1. Using a clean, damp cloth, wipe the inside of the oven including the racks.

2. Close the oven doors.

3. Push the Master Switch to ON.

4. Turn the Thermostat to 300°F (149°C) and allow the oven to cycle for 2 hours or until no odor is detected before pushing the Master Switch to OFF.

LIGHTING MODEL VC4GD AND VC6GD OVENS

1. Turn the main gas supply ON.

2. Push the Master Switch to ON.

3. If the burner fails to light, push Master Switch OFF. Wait 5 minutes for retrial.

If the oven does not light after three trials, turn off the main gas valve and call a qualified servicer.

SHUTDOWN INSTRUCTIONS

1. Turn Master Switch to OFF.

EXTENDED SHUTDOWN

1. Push Power Switch to OFF.

2. Turn gas and electrical power supplies OFF.

USING MODEL VC4GD AND VC6GD OVENS

Preheating

1. Select the proper rack arrangement for the product to be cooked. Refer to RACK ARRANGEMENTS, page 18.

2. Make sure the doors are closed.

3. Push Master Switch to ON. The amber ON light will come on, indicating that power to the oven is on.

4. Set the two-speed FAN SWITCH to the desired setting (without Roast & Hold models).

5. Set thermostat as desired. The HEAT light will come on and remain on until the oven reaches set temperature (approximately 10 to 15 minutes for settings from 300 to 400°F (149 to 204°C)). Refer to SUGGESTED COOKING GUIDELINES for temperatures and times for various products.

If the burner fails to light, the red IGNITION light will come on and remain on.

6. Prepare product and place in suitable pans. When the white HEAT light goes off, the oven has reached the desired preheat temperature.

– 12 –

LIGHTING OVEN (Model VC4GD-SEF)

(With standing pilot)

The oven fan continues to run when the oven door is opened. The oven

contains hot air and steam. Stay clear while opening the door.

1. Turn on main gas supply.

2. With Master Switch in OFF position, lift access door in lower trim, light pilot while holding red button on control panel.

3. Keep holding button for 30 seconds after pilot ignites.

4. Once steady pilot flame in achieved, close access door.

5. Set to desired temperature and fan speed.

6. Turn Master Switch to ON for weekly operation or SHABBOS for Sabbath Mode operation.

SHUTDOWN INSTRUCTIONS

1. Turn Master Switch to OFF position.

EXTENDED SHUTDOWN

1. Turn Master Switch to OFF position.

2. Turn main gas and electrical power supplies off.

– 13 –

Cooking

1. Open doors and load the product into the oven. Place pans in the center of the racks. Close doors.

2. Set the Timer. After the preset time lapses, turn Timer to OFF position to stop alarm.

3. When product is done, open doors and carefully remove cooked product from the oven. Care should be taken when wiping up spills, as oven is still hot.

Roast & Hold (When Equipped)

1. Turn the oven ON.

2. Set the Thermostat to the desired setting.

3. Position the Function switch to R & H.

4. Set the R & H TIMER to the desired roasting time.

• The oven will roast the product for the chosen set time and temperature. The oven controller will automatically switch from the roasting thermostat to the holding thermostat at the end of the preset roasting time. In holding mode the oven will maintain a temperature of 160°F (71°C) until the oven is turned off. The blower fan will run while the burner is on and the unit is operating in R & H.

5. To turn Cook & Hold off, flip the Function switch to the NORMAL position. The oven temperature will return to the thermostat setting.

End of Day

1. Turn Thermostat to OFF setting.

2. Push Master Switch to OVEN COOL. Leave door ajar while the fan is on to cool the oven.

3. When oven has cooled sufficiently, flip Master Switch to OFF.

4. Turn gas valve to OFF and clean oven.

Extended Shutdown

Repeat Steps 1 through 3 of End of Day. Unplug oven and shut off manual gas valve.

CONSERVING ENERGY— ALL MODELS

• Turn off unused equipment.

• Adjust menu patterns and cooking/baking schedules for optimum equipment use.

• Reduce thermostat settings in slack periods since gas equipment heats up and recovers quickly.

• Preheat only to required cooking temperature for specific food — not higher.

• Do not open the oven door unless absolutely necessary.

• Keep area around the oven door clean and free of food particles.

• Any obstruction that prevents the door from closing completely will adversely affect oven efficiency.

– 14 –

ROAST & HOLD OPERATION — (When Equipped)

400ºF

300ºF

200ºF

100ºF

ROAST AND HOLD DIAGRAM - Time vs. Temperature

SHORT BEEP. TIMER DISPLAYS "HOLD." ROAST THERMOSTAT OFF. HEATERS OFF UNTIL HOLD TEMPERATURE IS REACHED.

HEATERS MAINTAIN HOLD TEMPERATURE. TIMER DISPLAY FLASHES "HOLD."

OVEN TEMPERATURE TIMER DISPLAY COUNTS DOWN.

COOKING FROM STORED HEAT

LOAD PRODUCT INTO OVEN

PRODUCT TEMPERATURE

TEMP.

TIME

PREHEAT FIRST-STAGE COOKING SECOND-STAGE

COOKING (DO NOT OPEN

DOORS)

HOLDING

PL-56291

Roast & Hold cooks the product in two stages. During first-stage cooking, the oven temperature is regulated by the temperature setpoint and the R & H Timer setting. After the time counts down to 00:00, second-stage cooking begins. During second-stage cooking, the heat is off as the temperature in the oven declines to the hold temperature. The doors should remain closed during second-stage cooking.

When the hold temperature is reached, the oven temperature will be maintained at the hold temperature until the oven is turned off.

204°C

149°C

93°C

38°C

PROPER UTENSILS

The use of proper utensils can enhance oven operation. Medium and light weight pans allow the product to warm faster. Roast meats in shallow pans deep enough to hold all juices yet allow free air circulation.

OPERATING HINTS

When using the convection oven for the first time with a particular food, check the degree of doneness periodically before the suggested time has elapsed. This will ensure the desired doneness is achieved.

Record your temperature and time settings for various products. The convection oven can provide consistent and repeatable results.

The convection oven is faster than conventional deck-type ovens; temperature settings are lower and cook times are shorter. Since recipes and foods are subject to many variations and tastes, the guidelines regarding times and temperatures in this manual are SUGGESTIONS ONLY. Experiment with your food products to determine the cooking temperatures and times that give you the best results.

– 15 –

PROGRAMMABLE CONTROLS (Models VC4GC AND VC6GC)

R & H

MODE

OVEN

READY

OVEN

HEATING

PRIMARY

SECONDARY

SET

ROAST

HOLD

START

STOP

1/2

3/4

5/6

Always displays [HR:Min] when setting the time. Displays [HR:Min] if the countdown time is more than 1 hour.

Displays [Min:Sec] if the countdown time is less than 1 hour. Displays temperature in °F.

Indicates the oven is in the Roast & Hold Mode.

Indicates the oven is preheated and ready for cooking.

Indicates the oven is preheating or burners have cycled on to maintain temperature setting.

Primary indicates menu items 1, 3 or 5.

2 3 4

Secondary indicates menu items 2, 4 or 6.

Up arrow increases and Down arrow decreases a displayed time or temperature value (if arrow keys are lit).

TEMPERATURE: Use with SET to set the oven temperature.

SET: Use with time or temperature.

TIME: Use with SET to manually set the cooking time.

Selects Roast & Hold mode; also selects low fan speed.

Press once to start; press a second time to stop.

Select Menu Cook Times. Press once for primary (1, 3 or 5). Press a second time for secondary (2, 4 or 6). See next page.

Rack Buttons select individual Menu/Rack Number Cook

Times — once programmed.

– 16 –

+ 36 hidden pages