Vulcan Hart RSP-10 Installation Manual
INSTALLATION &
OPERATION MANUAL
RS-10
FOOD HOLDING & TRANSPORT
ROOM SERVICE CABINET
MODEL:
RS-10
RSP-10
For additional information on Vulcan-Hart or to locate an authorized parts
and service provider in your area, visit our website at www.vulcanequipment.com
VULCAN-HART 3600 NORTH POINT BLVD.
DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC BALTIMORE, MD 21222
www.vulcanequipment.com Vulcan ©2014 All Rights Reserved F-47119 (06-14)
RS-10 SERIES - HOLDING CABINETS F-47119 (06-14)
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
STAINLESS STEEL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SERVICE & PARTS INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1
RS-10 SERIES - HOLDING CABINETS F-47119 (06-14)
GENERAL
INTRODUCTION
Vulcan Holding Transport Cabinets are produced with quality workmanship and
material. Proper installation, usage, and maintenance of your cabinet will result in many
years of satisfactory performance.
It is suggested that you thoroughly read this entire manual and carefully follow all of the
instructions provided.
INSTALLATION
UNPACKING:
The Cabinet was inspected before
leaving the factory. The transportation
company assumes full responsibility for
safe delivery upon acceptance of the
shipment. Immediately after unpacking,
check for possible shipping damage to
the cabinet.
If the cabinet is found to be damaged,
save the packaging material and
contact the carrier within 15 days of
delivery.
CLEANING:
The cabinet should be thoroughly cleaned prior to putting into service.
Use a mild soap and water solution to clean the interior of the unit. Never use harsh
chemicals or abrasive pads to clean the unit.
Carefully unpack and place in a work
accessible area as near the installation
position as possible.
1. Open the door and carefully
remove any packaging materials
and the retaining straps that hold
the tray slides and tray slide
upright side supports.
2. Peel off vinyl protection film.
2
RS-10 SERIES - HOLDING CABINETS F-47119 (06-14)
CLEANING
DAILY:
1. Clean the interior of the cabinet
with a mild soap and water.
Never use harsh chemicals or
abrasive pads to clean the cabinet.
2. Rinse and dry with a soft dry
cloth.
3. Clean the exterior of the cabinet
with a clean damp cloth.
HEAVY-DUTY CLEANING:
For heavy-duty cleaning, use warm
water and a degreaser. Never rub in a
circular motion -- rub gently in the
direction of the steel grain.
Always rinse thoroughly.
STAINLESS STEEL CARE
CLEANING:
Stainless Steel contains 70 – 80% iron,
which will rust if not properly maintained.
Stainless Steel also contains 12 – 30%
chromium, which forms an invisible
passive, protective film that shields
against corrosion.
If the protective film remains intact, the
stainless steel will remain intact.
However, if the film is damaged, the
stainless steel can break down and rust.
PREVENTIVE CARE:
To prevent stainless steel breakdown, follow these steps:
1. Never use any metal tools,
scrapers, files, wire brushes,
or scouring pads.
2. Never use steel wool – which
will leave behind particles that will
rust.
3. Never use acid-based or
chloride containing cleaning
solutions – which will break
down the protective film.
4. Never rub in a circular motion.
Always rub gently in the direction
of the steel grain.
5. Never leave any food products
or salt on the surface. Many
foods are acidic. Salt contains
chloride.
PRESERVING & RESTORING:
Special stainless steel polishing
cleaners can preserve and restore the
protective film.
Preserve the life of stainless steel with a
regular application of a high-quality
stainless steel polishing cleaner, as a
final step to daily cleaning.
If signs of breakdown appear, restore
the stainless steel surface. First,
thoroughly clean, rinse, and dry the
surface. Then, on a daily basis, apply a
high-quality stainless steel polish
according to manufacturer’s instructions.
3
Loading...