Vulcan-Hart 52480, ICM24, ML-52470 User Manual

INSTALLATION &

OPERATION MANUAL

GAS INFRARED CHEESE MELTERS

MODEL

ICM24 ML-52470, 52476
ICM36 ML-52471, 52477
ICM48 ML-52472, 52478
ICM60 ML-52473, 52479
ICM72 ML-52474, 52480

MODEL ICM48

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. [phone]

FORM 30908 (11-94)

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS
EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND
ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE
EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED
FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN
UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE
LOCAL GAS COMPANY OR GAS SUPPLIER FOR
SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION OR MODIFICATION, SERVICE OR
MAINTENANCE CAN CAUSE PROPERTY DAMAGE,
INJURY OR DEATH. READ THE INSTALLATION,
OPERATING AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING
THIS EQUIPMENT.

IN THE EVENT OF A POWER FAILURE, DO NOT
ATTEMPT TO OPERATE THIS DEVICE.

– 2 –

Installation, Operation, and Care of

MODELS ICM24, ICM36, ICM48, ICM60 & ICM72

GAS INFRARED CHEESE MELTERS

KEEP THIS MANUAL FOR FUTURE USE

GENERAL

The Vulcan Gas Infrared Cheese Melters use efficient gas heat and are available in 24, 36, 48, 60, or
72 inch widths. Each model has one or two burners; each burner has its own pilot light and control knob.

GAS RATINGS

Model ICM24 ICM36 ICM48 ICM60 ICM72

BTU Rating 20,000 BTU/hr 30,000 BTU/hr 40,000 BTU/hr 50,000 BTU/hr 60,000 BTU/hr

INSTALLATION

UNPACKING

Immediately after unpacking, check for possible shipping damage. If the Cheese Melter is found to be
damaged, save the packaging material and contact the carrier within 15 days of delivery.

Before installing, verify that the gas (natural or propane) agrees with the specifications on the rating
plate located on the front.

LOCATION

The area around the appliance must be kept free and clear from combustibles. The area in front of and
above the Cheese Melter must be clear to avoid any obstruction to the flow of combustion and
ventilation air. Means must be provided for adequate air supply and adequate clearance for air
openings into the combustion chamber.

Adequate clearance must be provided in front and at the sides of the appliance for servicing and proper
operation.

The Cheese Melter can be installed in combustible or noncombustible locations. Clearance from
combustible construction must be a minimum of 6 inches from the sides and 0 inches from the back.
There are no minimum clearances from noncombustible construction.

The Cheese Melter can be installed on a noncombustible counter, with or without 4" legs, or mounted
on a combustible or noncombustible wall: Leg kits and wall mounting brackets are available from your
Vulcan-Authorized Service Office for your model Cheese Melter. If installing the Cheese Melter on a
combustible counter, the 4" legs are required.

– 3 –